Adobelite Orno User manual

18”-24”-30” Kiva Fireplace
GAS BURNING INSTALLATION MANUAL
RV-103012
Keep these instructions for future use.
This fireplace is to be installed ONLY by a con-
struction industry licensed contractor. Any
permits and construction industry inspections
required for installation should be obtained
by this contractor.
A) KIVA FIREBOX - A pre-cast firebox consist-
ing of real hand laid firebrick and light-
weight concrete.
B) EXTERIOR FIREPLACE FRAME - A tubular
steel and diamond-mesh frame. The frame
is finished with stucco after installation.
C) B-VENT CHIMNEY - Lightweight 6” type B-
Vent chimney is used for venting the fire-
place.
D) GAS LOG SYSTEM - Electronic Ignition Gas
Log Burning System is operated by a wall
switch or remote.
E) FIREBOX PEDESTAL - Concrete blocks are
used to elevate the firebox.
A
B
C
E
NOTE: All warnings are outlined in this manual and must be adhered to by the installer
and the buyer. Failure to do so will nullify the manufacturer’s warranty, and may cause
serious fire hazard.
The Adobelite Fireplace System consists of:
Frame Models: Orno
Santa Fe
Navajo
Zuni
D

2
WARNINGS AND GENERAL SAFETY PRECAUTIONS
Fully READ and UNDERSTAND all instructions
carefully before beginning installation.
ALL WARNINGS OUTLINED IN THIS MANUAL MUST BE STRICTLY
ADHERED TO BY THE INSTALLER AND HOMEOWNER.
FAILURE TO FOLLOW these installation instructions will
VOID THE WARRANTY and may cause a serious FIRE HAZARD.
DO NOT modify your fireplace in any way.
Any modification will void the warranty and
create a potential fire hazard.
Before burning your first fire, fully read the
“Homeowners Operation Manual”.
Combustion Air Intake of fireplace must be
kept clear of debris at all times.
This fireplace is to be installed ONLY by a construction industry licensed contractor. Any permits and
construction industry inspections required for installation should be obtained by this contractor.
Do not store or use flammable liquids or
aerosols near this fireplace.
Never leave the fireplace burning while unat-
tended.
Children should never be left unattended
while the fireplace is in use.
WARNING: Only use approved chimney and
termination systems outlined in this manual.
WARNING: This fireplace is NOT designed for
wall termination. Fireplace must be vented
vertically.
IMPORTANT: THESE INSTRUCTIONS MUST BE LEFT
WITH HOMEOWNER

3
TABLE OF CONTENTS
Warning and Safety Precautions ………………………………………………...……..2
Listing Data Plate / Location…………………………………………………………….….4
1. Pre-Installation Requirements ……………………………………………………..5
Firebox Dimensions………………………………………………………………….5,6
Chimney Requirements……………………………………………………………….6
Gas Requirements…….……………………………………………………………...…7
Electrical Requirements……………………………………………………………...8
Fireplace Layout……………………………………………………………………….8,9
Fireplace Pedestal…………..…………………………………………………………..8
2. Firebox Installation………………………………………………………………..……10
Firebox Assembly ………………………………………………………………...... 10
Door Frame …..………………………………………….…………………………….. 11
Anchor Plate……………... ……………………………………………………….……11
3. Chimney Installation……………………………………………………………………12
Installing the Chimney Pipe………………………………………………… 12-15
Outside Air Kit Installation……………………………………………………….. 15
4. Kiva Frame Installation………………………………………………………………..16
5. Finishing the Fireplace……………………………………………………………..….17
Lava Rock / Gas Log Setup……………………………………………………….…18
6. Operation and Trouble Shooting ………………………………………………..19
7. Adobelite Kiva Fireplace Options………………………………………….…….20

4
MODEL TYPE / SIZE SERIAL NUMBER
FIG. 1 - LISTING DATA PLATE LOCATION
LISTING DATA PLATE / LOCATION
The Adobelite Kiva Fireplace is a factory built fireplace
tested to U.L. 127. Locate the Listing Data Plate on the
upper left backside of the Kiva Firebox Front Arch. Record
the model, size, and serial number listed on the data plate
below.
PLEASE FILL IN THE FOLLOWING INFORMATION FOR FUTURE REFERENCE
Model Type / Size: ________________
Frame Style: __________________________________ Dealership Purchased at: ______________________________________
Dealership Phone #: __________________________________________
Date Purchased: ________________ Date Installed: ___________________
Serial Number: ________________________________
Chimney Pipe Brand: ____________________________ Chimney Pipe Size (Inner/Outer): _______________________________
Notes: _______________________________________________________________________________________________________
_____________________________________________________________________________________________________________
_____________________________________________________________________________________________________________

5
1
PRE-INSTALLATION REQUIREMENTS
KIVA18 FIREBOX DIMENSIONS:
TOP VIEW
A B C D E F G H
KIVA 18 20 1/4”27” 18 1/4”35” 38” 22 1/2”6” MIN. 10 1/2”
CLEARANCES TO COMBUSTIBLES
SIDES/BACK 1”
FACE All framing along firebox face
must be non-combustible
CHIMNEY 1”
KIVA24 FIREBOX DIMENSIONS:
TOP VIEW
A B C D E F G H
KIVA 24 25 1/4”34” 25” 44” 47 1/2”25 1/2”6” MIN. 10 1/2”
CLEARANCES TO COMBUSTIBLES
SIDES/BACK 1”
FACE All framing along firebox face
must be non-combustible
CHIMNEY 1”

6
CHIMNEY REQUIREMENTS
GAS BURNING
For minimum chimney sizes and types see table below. Certified equivalents tested and listed to UL Test Procedure
103, and ULC S604 may also be used if minimum chimney diameter is adhered to.
Chimney Type and Sizes Minimum
Clearance I.D. Chase Size
KIVA 18 6” I.D. / 63/4” O.D. B-Vent 1” 9” x 9” minimum
KIVA 24 6” I.D. / 63/4” O.D. B-Vent 1” 9” x 9” minimum
KIVA 30 6” I.D. / 63/4” O.D. B-Vent 1” 9” x 9” minimum
WARNING! B-Vent Chimney should never be used when solid fuels are to be burned!
TABLE 1. chimney requirements
KIVA30 FIREBOX DIMENSIONS:
TOP VIEW
A B C D E F G H
KIVA 30 30” 40” 27 1/4”48 1/2”51 1/2”28” 6” MIN. 12 1/2”
CLEARANCES TO COMBUSTIBLES
SIDES/BACK 1”
FACE All framing along firebox face
must be non-combustible
CHIMNEY 1”
Fireplace installation must be in compliance with local building codes. Before installing the fireplace, consult
the local construction industry to ensure that you are in compliance with all applicable codes, including permits
and inspections.
WARNING: THE FIREBOX MUST BE FINISHED WITH THE ADOBELITE KIVA METAL FRAME OR OTHER NON-
COMBUSTIBLE MATERIALS. CLEARANCES TO COMBSTIBLE MATERIALS AND FRAMING MUST BE MAINTAINED.

7
GAS REQUIREMENTS:
18” FIREBOX MODELS
MODEL A (min.) B
Key Valve / Switch Stub Out
Ornito 3’4” 2’6”
Santa Fe 3’10” 3’0”
24” FIREBOX MODELS
MODEL A (min.) B
Key Valve / Switch Stub Out
Orno 3’8” 2’8”
Santa Fe 4’2” 3’2”
Navajo 4’8” 3’2”
Zuni 4’8” 3’2”
30” FIREBOX MODELS
MODEL A (min.) B
Key Valve / Switch Stub Out
Orno 4’2” 3’2”
Santa Fe 4’4” 3’4”
Navajo 4’10” 3’4”
Zuni 4’10” 3’4”
The 1/2” gas stub out should be located at a
height of 6” from the floor and a distance
from the corner specified by B in the charts
below. It should extend no more than 2” to
3” from the wall and be capped off until it is
hooked up to the fireplace.
The Adobelite Gas Log system requires 1/2” gas supply line capable of supplying an input BTU of 48,000 for
Natural Gas, and 39,700 for Liquid Propane.
STUB OUT
Before the Adobelite firebox is installed, gas lines should be run into the area where the fireplace will be in-
stalled. A Keyed Gas Shutoff Valve is required in an accessible location within 3’ of the fireplace. Use figure A, in
the charts below to locate the minimum distance from the corner where the Keyed Gas Shutoff Valve can be
placed to insure it will not be behind the Adobelite Frame when installed. It should also be at a minimum height
of 1’8”.
KEY VALVE
BTU REQUIREMENTS
IMPORTANT: All gas connections and gas piping must be installed by a construction industry
licensed contractor. Any permits and construction industry inspections required for installation
should be obtained by this contractor.
FIG. 1 - GAS SHUTOFF AND STUB OUT
KEYED GAS
SHUTOFF VALVE
1’8”
6”
MILLI-VOLT
WIRES
ELECTRICAL BOX
AND SWITCH
A
B
1/2” GAS
STUB-OUT
1/2” GAS SUPPLY
LINE
A

8
ELECTRICAL REQUIREMENTS:
LAYOUT (FIG. 4, FIG. 5)
CARPET
Carpet and padding will need to be removed up to the hearth line. See FIG. 4 and FIG. 5 below.
Begin the layout by drawing a center line at 45 degrees for a corner installation, or perpendicular to the wall for
a flat-wall installation. Next, draw the baseline (dimension D - refer to FIG. 4 below and FIG. 5 on page 8) perpen-
dicular to the center line. The base line will be aligned with the front edge of the Firebox Base and the Firebox
Pedestal.
CORNER LAYOUT
18” FIREBOX MODELS
MODEL A B C D
Frame at
Ceiling
Frame at
Hearth Hearth Baseline
Ornito 2’2” 2’10” 4’3” 2’4”
Santa Fe 2’4” 3’4” 4’9” 2’4”
24” FIREBOX MODELS
MODEL A B C D
Frame at
Ceiling
Frame at
Hearth Hearth Baseline
Orno 2’2” 3’2” 4’5” 2’5”
Santa Fe 2’6” 3’6” 4’11” 2’5”
Navajo 3’0” 4’0” 4’11” 2’5”
Zuni 3’0” 4’0” 5’5” 2’5”
30” FIREBOX MODELS
MODEL A B C D
Frame at
Ceiling
Frame at
Hearth Hearth Baseline
Orno 2’6” 3’6” 4’11” 2’9”
Santa Fe 2’8” 3’8” 5’1” 2’9”
Navajo 3’2” 4’2” 5’1” 2’9”
Zuni 3’2” 4’2” 5’7” 2’9”
CENTER LINE
BASE LINE
FIG. 4 - CORNER LAYOUT
ELECTRICAL BOX AND SWITCH
Install an Electrical Box and Wall Switch at the desired location. Refer to FIG. 1 on page 7 to locate the minimum
distance from the corner that the Switch should be located. 8 Feet of 20 AWG Milli-volt wire is included pre-
wired to the gas system controls, which is to be connected to the switch terminals.
WARNING: LOW VOLTAGE AND 110 VAC VOLTAGE CANNOT SHARE THE SAME ELECTRICAL BOX
This fireplace comes equipped with a 3 volt electronic ignition gas control system. This system includes a two
D-cell battery pack prewired to the gas system controls, which will provide reliable operation of the system even
in the event of a power outage. Battery polarity must be correct or module damage will occur. An optional 3 volt
AC transformer is available from Adobelite or your dealer for operation using 110V AC. The optional transformer
and the included battery pack CANNOT both be hooked up to the control module at the same time or damage
will occur. Remove batteries from the battery pack before connecting the optional transformer, and unplug the
transformer before installing the batteries.

9
CENTER LINE
BASE LINE
24” FIREBOX MODELS
MODEL A B C D E F G
Width at
Ceiling
Width at
Firebox
Width of
Hearth Baseline Depth at Ceiling
Depth at
Firebox
Depth of
Hearth
Orno 2’0” 4’0” 6’7” 1’11” 1’8” 2’8” 4’0”
Santa Fe 1’6” 4’0” 6’7” 1’11” 1’5” 2’8” 4’0”
Navajo 1’6” 5’0” 6’7” 1’11” 1’5” 2’8” 4’0”
Zuni 1’6” 5’0” 7’7” 1’11” 1’5” 3’3” 4’6”
30” FIREBOX MODELS
MODEL A B C D E F G
Width at
Ceiling
Width at
Firebox
Width of
Hearth Baseline Depth at Ceiling
Depth at
Firebox
Depth of
Hearth
Orno 2’8” 5’0” 7’5” 2’1” 2’0” 3’0” 4’4”
Santa Fe 2’2” 5’0” 7’5” 2’1” 1’9” 3’0” 4’4”
Navajo 2’2” 6’0” 7’5” 2’1” 1’9” 3’0” 4’4”
Zuni 2’2” 6’0” 8’5” 2’1” 1’9” 3’6” 4’10”
FIG. 5 - FLAT-WALL LAYOUT
FIG. 6 - FIREBOX PEDESTAL
4” x 8” x 16”
Concrete Block
8” x 8” x 16”
Concrete Block
H
18” Firebox 24” Firebox 30” Firebox
H - Block Spacing 5” 6” 9”
12”
Total Height
FIREBOX PEDESTAL:
Standard Hearth Height of 18”
(Note: Concrete Blocks are not included
with the Adobelite Fireplace Kit and must
be purchased separately)
Concrete Masonry Units (C.M.U) are
used to construct the Firebox Pedes-
tal. The overall height of the pedes-
tal should be 12”. A combination of
two 8”x8”x16” and two 4”x8”x16”
CMU can be stacked (as shown in
FIG 6), or any other combination of
concrete blocks can also be used as
long as the overall height is 12”.
1) Two columns of CMU’s should be
positioned with the front edge of
the blocks against the Firebox
Base Line. Refer to Block Spacing
dimension (H) in positioning the
width of the block pedestal. The
blocks should be equally spaced
from the center line.
2) Adhere the concrete blocks to
each other and to the concrete
slab as they are assembled using
mortar or a construction adhe-
sive such as Liquid Nails or F26.
WARNING: ONLY NON-COMBUSTIBLE MATERIAL
MAY BE USED FOR THE FIREBOX PEDESTAL!
For Hearth Height below 18”
Concrete Floor
When working on a concrete
floor, the base section (shown in
step 1, page 9) can be set directly
on the floor if desired, for a 5”
hearth height.
Wood Floor
The hearth height can also be lowered to 11” for
a wood floor. If you plan to lower the firebox
pedestal lower than 8”, you must use a heat bar-
rier consisting of: 1) a layer of 1 ¼” thick split
firebrick, 2) a 16 gauge steel barrier (the same
size as the base, and 3) another layer of 1 ¼”
firebrick. The steel barrier should be sandwiched
in-between the firebrick. Only adjust the base
pedestal height if: 1) you ordered a custom
frame at that height, or 2) you feel comfortable
performing the necessary modifications to the
frame.
BASE LINE

10
1) BASE –Spread a thin layer of concrete mortar or construction adhesive
on the top of the firebox pedestal. Place the firebox base on the pedes-
tal. Using the layout sketch, align the front of the base with the firebox
base line and center the firebox along the center line. Make sure the
Base is level.
FIREBOX ASSEMBLY 2
2) LOWER BACK –Apply a 5” wide thin layer of the included refractory
mortar to the outside top edge of the base where the Lower Back will
rest. Place the Lower Back in place and rotate the piece slightly back
and forth to squish the mortar into place. Align the back and sides of
the Lower Back and Base.
3) UPPER BACK (MODELS KIVA24 AND KIVA30 ONLY) –Following the
above procedure, spread a layer of refractory mortar and place the Up-
per Back section on top of the Lower Back. Again, align the back and
sides of the pieces.
6) TOP –Now install the top section of
the fireplace. Again, spread a thin
layer of refractory mortar where
the pieces will meet, and align the
5) FRONT ARCH –Apply refractory
mortar to the front edges of the
Lower and Upper Back pieces and
to the top of the Front Arch sec-
tion. Place the Front Arch into place
and attach using four 1/4” x 6” Lag
Bolts. Avoid placing any weight
onto the Manifold before the bolts
are attached.
6
6 –Top
2
2 –Lower Back 3 –Upper Back
3
1
1 –Base
6” Bolts
5
5 –Front Arch
4) MANIFOLD AND GAS SYSTEM –Apply a 1” wide layer of refractory mor-
tar to the upper face of the fireplace base. Position the Manifold so
that the face of the Manifold is against the face of the base, and the L-
Bracket (that supplies combustion air) is resting on the firebrick surface
of the Base. The Burn Pan and Kiva Grate will rest on the Base towards
the back. Using the supplied ¼” x 3” lag bolts, bolt the manifold to the
Base. The heads of the bolts will pass through the face of the manifold
and tighten against the back of the manifold. Do Not Over-tighten the
Bolts! Using your finger, apply refractory mortar to all the seams where
the manifold touches the Base.
4
4 –Manifold and Gas System
¼” dia. x 3” lag bolts
L–Bracket
Burn Pan and
Kiva Grate

11
7) DOOR FRAME –The Door Frame
allows an Adobelite Screen Door or
Glass Door to be used with the fire-
place. Begin by attaching the Door
Frame to the Manifold. Position the
Door Frame on top of the Manifold
and allow a 1/2” space between the
1/2” Angle Iron on the top of the
Access Door and the Door Frame.
Use two 11/4” x #8 self drilling (black
head) screws to secure the Door
Frame to the Manifold.
FIREBOX ASSEMBLY (CONTINUED):
7
Front Arch
7
1/2” Angle Iron
1/2” Space
7A –Door Frame
5” Black
Head Phillips
Screws
8) B-VENT ANCHOR PLATE–Apply a thin layer of refractory mortar to the top of firebox where the Anchor Plate
will sit. Align the back edge of the Anchor Plate opening with opening in the firebox top section. Secure the
Anchor Plate using four ¼” dia. x 3” long lag bolts.
Plumb the Door Frame vertically,
then secure the Door Frame to the
Front Arch using two 5” (black
head) wood screws.
Finally, the Ball Catch (FIG. 7B)
needs to be installed to the door
frame. Begin by drilling a 1” deep x
3/4” dia. hole through the mounting
tab and into the Front Arch. Slide
the Ball Catch up into the hole and
secure it to the mounting tab on the
Door Frame with the two provided
brass screws.
7B –Ball Catch
8 –Anchor Plate / Damper
8
¼” dia. x 3”
lag bolts
3/4” x 1” Hole
7
Front Arch
Ball Catch
Screws
Mounting Tab
Access
Door

12
Each section of B-Vent chimney consists of an inner and outer flue
pipe. As the flue sections are assembled, the upper flue section will
slip to the inside of the section below.
To join two sections of chimney pipe together, line up the male end
slot (lower piece of pipe) with the female end of the locking lug
(upper piece of pipe). Push the two sections together, and then ro-
tate the upper piece clockwise to securely lock the two pieces to-
gether. If the chimney is pulled upward it will not separate from the
pipe below if it is properly locked.
Except where the first section of pipe joins to the Anchor Plate (see
FIG 10), screws are not necessary to join the chimney pipe. If desired,
1/4” sheet metal screws may be used to secure the outer sections of
chimney. Do not penetrate the inner liner!
10) STARTER ELBOW –Begin the chimney installation by inserting
the inside liner of the starter elbow to the inside of the Anchor
Plate collar. The outside section of pipe will fit to the outside of
the Anchor Plate collar.
Align the inner Starter Elbow so that it points directly back away
from the Firebox face. Then, secure the elbow to the Anchor Plate
collar using the supplied #6 x 1/2” self drilling hex head screws. Do
not penetrate the inner chimney liner.
11) SPACER SECTIONS –Attach one or more straight sections of
chimney pipe together to offset the chimney into the desired
area. Refer to the Layout Charts on pages 8 and 9 to make sure
the chimney is offset enough to clear the top of the Kiva Frame. A
18” section of chimney is typical for most installations.
WARNING: A MINIMUM OF 1” AIR CLEARANCE MUST BE MAINTAINED BETWEEN ALL CHIMNEY COMPONENTS
AND COMBSTIBLE MATERIALS. ALL INSTRUCTIONS PROVIDED BY CHIMNEY MANUFACTURERS MUST BE
STRICTLY ADHERED TO. FAILURE TO PROPERLY FOLLOW ALL CLEARANCES AND INSTRUCTIONS MAY RESULT IN
A SERIOUS FIRE CAUSING INJURY OR DEATH!
CHIMNEY INSTALLATION 3
CHIMNEY INSTALLATION
ANCHOR PLATE
COLLAR
FIG. 10 - STARTER ELBOW
10
LATERAL CHIMNEY SLOPE
If the chimney system contains
lateral (horizontal) sections, they
must maintain a minimum up-
wards slope of 1/4” rise for every
horizontal foot.
Minimum slope of
1/4” rise per foot of
run required
FIG. 11 - STRAIGHT SECTIONS
11

13
12) STRAIGHT CHIMNEY SECTIONS –Before running the
straight chimney through the roof, slide the Firestop Spacer
(shown in FIG. 13) over the Return Elbow. Then, twist lock
the remaining Straight Chimney sections into place.
Locate and mark the center of where the chimney will pass
through the ceiling or wall. Cut and frame a 9” x 9” hole for
the chimney to pass through. A 1” min airspace must be
maintained between the chimney pipe and all combustible
materials.
CHIMNEY INSTALLATION (CONTINUED):
WARNING: CHIMNEY
PIPE MUST TERMINATE
VERTICALLY! IF CHIMNEY
PIPE IS RUN THROUGH
AN EXTERIOR WALL, A
RETURN ELBOW MUST
BE USED TO RETURN THE
CHIMNEY TO VERTICAL,
AND THE TERMINATION
CAP MUST EXTEND 2’
ABOVE ANY WALLS
WITHIN 8 FEET!
YES
NO!
9”
FIG. 12 - STRAIGHT CHIMNEY
12
1” MIN. AIR
SPACE TO
COMBUSTIBLES!
9”
Chimney Enclosures: A framed enclosure is required any where
the chimney passes through an occupied area. Refer to Chimney
Chase Requirements on page 14 for more information.
joist space. Attach Firestop Spacer to joist using wood screws. If the chimney pipe passes through a framed
opening into an attic space, the Firestop must be placed in the attic floor. When the pipe passes through a
framed opening into living space above, the Firestop must be placed onto the ceiling from below. Firestops
are required when passing through a wall. Firestops may be fabricated from sheet metal, provided that the
required 1” clearance is maintained and acceptable to Local Building Authorities. Refer to local building
codes and restrictions for variations in Firestop spacer requirements.
Pipe strapping should be
used to secure the re-
turn elbow to two studs.
This will stabilize the
chimney pipe and carry
the weight of the
straight vertical pipe.
13) FIRESTOP SPACERS –
Firestop Spacers are re-
quired at each point
where the chimney
penetrates a floor ceiling
FIG. 13 - FIRESTOP SPACERS
13

14
PARAPIT WALL
OR OBSTRUCTION 1” MIN.
2’ MIN.
FIG. 14.2 - CHIMNEY CHASE
CHIMNEY CHASE REQUIREMENTS
If the chimney pipe passes through any living space , an en-
closure/chase must be constructed. An optional enclosed
chimney chase may be constructed to conceal exposed
chimney above the roof line, and is recommended if the
chimney is run on the exterior of a wall (particularly in cold
climates). The chase should be constructed with a minimum
open clear space of 9”x9” and a minimum of 1” air space
from the pipe to all combustibles. Framing should be con-
structed of 2 x 4 lumber or heavier. Fire-blocking is required
between the joists in which the flue will be installed.
When an exterior roof chase is constructed (see FIG. 15), a
½” plywood or wafer board should cap the chase in which a
minimum diameter circle of 2” larger than the pipe diameter
should be removed. The chimney must terminate at least
2’0” above the parapet, adjacent wall, or any other obstruc-
tion within 8’.
CHIMNEY INSTALLATION (CONTINUED):
15) CHIMNEY ROOF FLASHING –Slide the Chimney Roof Flash-
ing down over the last section of straight chimney. Make
sure that the 1” clearances are maintained and then nail the
flashing down to the roof or chase. The roofing material
(asphalt paper, shingles, etc.) should overlap the top or up-
hill side of the flashing. Use a non-hardening sealant to seal
the edges of where the flashing meets the roof.
15
FIG. 15 - CHIMNEY ROOF FLASHING
IMPORTANT: If an exposed portion of chimney is greater than 5’
above the roof line, use support wires to keep chimney secure.
The support wires may be attached to the outer pipe of the
chimney with screws but must not penetrate the inner flue pipe.
WARNING: DO NOT SEAL VENTILATION OPENINGS ON THE
ROOF FLASHING WITH INSULATION OR OTHER MATERIALS!
14) TERMINATION HEIGHT REQUIREMENTS
The termination height of the chimney is determined by the roof pitch, and also the distance from adjacent
walls or obstructions. The chimney must extend a minimum of 1 foot above the roof (refer to FIG. 14.1 and
FIG. 14.2 below). If the chimney is within 8’ of any walls or obstructions, the chimney must extend a mini-
mum of 2’ above the obstruction.
HEIGHT REQUIREMENTS
ROOF PITCH H (Min.)
Flat to 6/12 1’0”
6/12 to 7/12 1’3”
7/12 to 8/12 1’6”
8/12 to 9/12 2’0”
9/12 to 10/12 2’6”
10/12 to 11/12 3’3”
11/12 to 12/12 4’0”
14/12 to 16/12 6’0”
16/12 to 18/12 7’0”
18/12 to 20/12 7’6”
20/12 to 21/12 8’0”
12 X
Pitch of
Roof
Is X/12
2’ MIN
H
8’ or less
FIG. 14.1- TERMINATION HEIGHT

15
CHIMNEY INSTALLATION (CONTINUED):
16) STORM COLLAR –Slide the Storm Collar down
around the outside chimney pipe. Using non-
hardening weather proof sealant/caulk to make
a waterproof seal, seal the Storm Collar against
the chimney pipe and the flashing.
17) TERMINATION CAP –Finally, connect the Ter-
mination Cap to the last straight chimney section
by twist locking the Termination Cap clockwise.
18) INSPECTION –Perform a final inspection to in-
sure all joints are secure, chimney is properly
supported, and that the 1” clearance to combus-
16
17
CAULK
FIG. 16 - STORM COLLAR AND TERMINATION CAP
OUTSIDE AIR KIT INSTALLATION:
20) OUTSIDE AIR VENT –If the
fireplace is located against
an exterior wall (FIG 20.1),
use a hole saw to cut a hole
completely through the exte-
rior wall. Use the layout
charts (Pages 5-6) to make
sure that the Adobelite Kiva
Frame will cover the hole
and Outside Air Vent. The
center of the hole should be
WARNING: FOR PROPER OPERATION THIS FIREPLACE REQUIRES THE OUTSIDE AIR KIT TO BE INSTALLED.
The Outside Air Kit is used to
provide outside combustion air
to the firebox, therefore not
20
4” HOLE
FIG. 20.2 - OUTSIDE AIR VENT (CHIMNEY CHASE)
20
4” HOLE
FIG. 20.1 - OUTSIDE AIR VENT (EXTERIOR WALL)
located about 8” from the bottom of the wall. If
the fireplace is not located on an exterior wall, the
outside air can be brought down from the chim-
ney chase (FIG 20.2). Cut a 4” hole located on a
vertical face of the chimney chase and attach the
Outside Air Vent.
21) ALUMINUM FLEX DUCT –Using Metal Tape, se-
cure the Aluminum Flex Duct to the Outside Air
Vent and to the open end of the Manifold.
Connect the ½”gas inlet on manifold (FIG. 21) to the keyed gas shutoff valve and test for any gas leaks. Connect
the brown 20 AWG wires from the left end of the manifold to the wall switch (see Page 8 for specifications).
Open the keyed gas shutoff valve and ignite the fireplace by flipping the wall switch. It is normal for the fireplace
to take longer to light at this stage as the air trapped in the line will need to bleed out. Refer to Operating In-
structions for more information.
FIG. 21 - ALUMINUM FLEX DUCT
21
½” Gas Inlet
GAS SYSTEM CONNECTIONS:
IMPORTANT: All gas connections and gas piping must be installed by a construction industry
licensed plumber or gas fitter. Check all gas connections for leaks. It is possible that connection may
have loosened during shipping!

16
KIVA FRAME INSTALLATION:
ATTACH LATH TO MANIFOLD (FIG. 22)
Before placing the Kiva frame around the firebox,
Lath needs to be attached to the front of the manifold.
Cut a strip of lath 24” x 27”. Fold the 24” side in half and
place a sharp crease at the bend. Open the piece up and
place the bent edge 1” down from the top of the manifold.
Using the #6 x 1/2” self drilling phillips washer head screws,
attach the lath every 3”. Finally bend the bottom section of
the lath up to meet the top section so they can both pass
through the opening of the Kiva frame.
WARNING: Use care and wear gloves when handling the frame and diamond lath pieces. Cut edges of the diamond lath
mesh are very sharp!
ATTACH LATH FROM FIREBOX TO FRAME (FIG. 23)
Begin by placing the Kiva Frame into position in front of the
Firebox. Measure from the frame to the corner or flatwall
to make sure the frame equal distance on both sides. Bring
the folded lath that was attached to the Manifold (FIG. 22)
through the opening in the Kiva Frame. Attach the folded
section of lath to the Kiva Frame using #6 x 1/2” Hex Head
Self-Drilling Screws. Any loose sections of lath can also be
attached by fishing bailing wire through the pieces and
tightening.
Next, cut several strips of diamond lath mesh 16” wide.
Place the lath strips against the inside Front Arch even with
the Door Frame (FIG. 23). Using 15/8” washer head screws,
attach the lath to the Front Arch every 4”. Cut strips in the
opening lath from the outside edge up to the opening bar.
Fold the strips back onto the frame. Attach the lath strips to
the frame using #6 x 1/2” self drilling hex head screws, or
with bailing wire.
15/8” Washer
Head Screws
Cut Lath
FIG. 23 –ATTACH LATH STRIPS
#6 x 1/2” Hex Head
Self-Drilling Screws
ATTACH KIVA FRAME TO WALLS AND CEILING
Using #8x 15/8” Phillips washer head pointed screws, attach
the lath from the frame to the walls and the ceiling. Screws
should attach the lath about every 4”. Some of the screws
will only go into the sheetrock and not the studs. Fold the
lath back onto the Kiva Frame and attach to the metal tub-
ing using self drilling screws, or tie the lath down with bail-
ing wire so that it is secure. Any gaps in the lath can be
filled in with by cutting strips of lath and attaching to the
Kiva Frame and walls / ceiling.
4
15/8” Washer
Head Screws
FIG. 24 –ATTACH KIVA FRAME TO WALLS
WARNING: THE FIREBOX MUST BE FINISHED WITH THE
ADOBELITE KIVA METAL FRAME OR OTHER NON-
COMBUSTIBLE MATERIALS. CLEARANCES TO COMBSTIBLE
MATERIALS AND FRAMING MUST BE MAINTAINED.
#6 x 1/2”
Phillips
Washer Head
Self-Drilling
Screws
Diamond Lath Mesh
FIG. 22 –MANIFOLD LATH

17
The fireplace can be finished with any indoor plaster system. Typically a 3-coat system is used. The first coat
should be a cement based product with fiberglass and sand. This will provide a solid base for the other coats. The
first coat can be mixed slightly on the dry side to help it bond to the Kiva Frame wire mesh. Allow the first coat to
dry completely before applying the 2nd coat.
The 2nd coat should contain fiberglass, and may or may not contain sand and cement. Many indoor plasters are
gypsum based. Apply the 2nd coat using a trowel, and then smooth out the plaster using water and a float (or
sponge). When complete the 2nd coat will be fairly smooth but will have a “grainy” of stucco finish.
Allow one full week or more for the first two coats to completely dry before applying the final coat of plaster.
The final coat does not contain fiberglass and is generally applied with a hard trowel to give a smooth appear-
ance, but can be also be finished any way desired.
5
FINISHING THE FIREPLACE
3-COAT PLASTER FINISH
PAINTING THE PLASTER
Once the plaster is completely dry, the fireplace can be painted if desired. Adobelite recommends using a latex
based primer and paint. If the fireplace has been burned in, clean any soot buildup along the opening of the fire-
place using a mild dish detergent and water before painting.
SEALING THE PLASTER
The plaster can be sealed which will help keep the plaster from discoloring, and also make the fireplace easier to
clean. Many types of sealers are available, such as: wax sealers, which will give the plaster a shiny (almost wet
look), and masonry and grout sealers, which are available in matte and gloss finishes. Check with your plaster
supplier for options.

18
CERAMIC LOG INSTALLATION
LAVA ROCK
Spread the supplied lava rock onto the bottom of the firebox. The lava
rock should form an even layer across the base covering all the wires and
tubing to the burn pan, but not the burn pan itself.
GLOWING EMBERS
Tear the supplied Glowing Embers into dime sized pieces. Place the
pieces all around the burner holes on top of the burner pan making sure
not to cover the burn holes where the gas will come out of. See FIG 25.
LOG PLACEMENT
Refer to figures below for proper placement of Ceramic Logs. The logs
should sit in-between the large burn holes of the Burn Pan. See FIG 26.
FIG. 25 - GLOWING EMBERS
FIG. 26 - CERAMIC LOG PLACEMENT
1 2 3
4 5 6
Burn Pan
Burn Holes

19
6
OPERATING AND TROUBLESHOOTING
OPERATING THE FIREPLACE
The Adobelite Gas Fireplace uses an electronic/intermittent pilot system. When the wall switch is flipped to the
on position, the control system sends a spark and ignites the pilot light. Once the heat sensing rod at the pilot
heats up, the main burner turns on and ignites. When the wall switch is turned off both the main burner and pi-
lot light will turn off.
1. Fully open the Keyed Gas Shutoff Valve located on the wall (shown on Page 7).
2. Flip the Wall Switch to the “on” position.
 You may hear a “clicking” sound as the igniter lights the pilot flame. If this is the first time operating
the fireplace it may take several seconds for the air in the gas line to bleed out before the pilot
ignites.
3. When done using the fireplace, flip the wall switch to the “off” position. It is not necessary to close the Keyed
Gas Shutoff Valve when you are not using the fireplace.
IMPORTANT: WHAT TO DO IF YOU SMELL GAS. 1) Shut off gas to fireplace. 2) Extinguish and flame. 3) Go to a phone
outside your home and call your gas supplier. If you can’t reach your gas supplier, call the Fire Department.
TROUBLE SHOOTING
SYMPTOMS POSSIBLE CAUSE SOLUTION
Pilot does not make a “clicking”
sound, and will not ignite
Batteries need replacing Replace 2—D cell Batteries located
in access door (See FIG 7A, pg. 11)
Wall switch faulty Check wall switch
Air trapped in gas line Bleed Gas Lines
Pilot makes a “clicking sound, but
won’t ignite Keyed Gas Valve Closed Open Keyed Gas Valve
Fireplace will ignite and burn for a
few seconds, cycle off, and re-ignite
Pilot Sensor Rod not getting enough
flame
Gently bend Sensor Rod towards
Pilot Hood so it is in direct contact
with flame (See FIG 27 )
Soot on Logs
Burner holes covered by glowing
embers or logs
Adjust glowing embers and logs so
they do not block burner holes
Air Mixer Closed Open Air Mixer by turning Air Mixer
Nut counter clockwise (See FIG 28)
Igniter Rod
Pilot Hood
Sensor Rod
Back of Burn Pan
FIG. 27 - PILOT SENSOR ROD
Burner Holes
Air Mixer Nut
Air Intake Holes
FIG. 28 - AIR MIXER

20
ADOBELITE KIVA FIREPLACE OPTIONS: 7
Nicho (Set of 2)
Nichos can be added to any of the Adobelite Kiva
Frames. Inside measurements before plaster are: 12”
wide x 12” tall x 5” deep.
Sidewall Banco
Sidewall Bancos are 15 3/4” tall x 15 3/4” deep (before
plaster) to match the height of the Adobelite Kiva
Frame hearth extension and are available in lengths
of 2’ to 10’. Specify left or rights side when ordering.
Wood Storage Bin
The Wood Storage Bin has
an interior size of 24” wide
x 12” high x 16” deep. It fits
in the center of the hearth
extension or the Sidewall
Banco
Glass Door and Screen Door
GLASS DOOR SCREEN DOOR
Tempered Glass, Ceramic Glass, and Screen Doors are available from
your dealer.
All doors our hand made, and snap into place using the provided door
frame for a clean, elegant look.