ADT A-CE6TW2812UW User manual

1/3'' DOUBLE SCAN CCD
HIGH RESOLUTION
WDR Super High Resolution
Day & Night Color Camera

- ii -
WARNINGS:
CAUTION:
CAUTIONCAUTION
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER(OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
EXPLANATION OF GRAPHICAL SYMBOLS
The lightning flash with arrowhead symbol, within an equilateral triangle, is
intended to alert the user to the presence of uninsulated "dangerous voltage"
within the product's enclosure that may be of sufficient magnitude to constitute a
risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to
the presence of important operating and maintenance (servicing) instructions in the
literature accompanying the product.
Should any liquid or solid object fall into the cabinet,
unplug the unit and have it checked by the qualified
personnel before operating it any further.
Unplug the unit from the wall oulet if it is not going to
be used for several days or more. To disconnect the
cord, pull it out by the plug. Never pull the cord itself.
Allow adequate air circulation to prevent internal heat
build-up. Do not place the unit on surfaces (rugs,
blankets, etc.) or near materials(curtains, draperies)
that may block the ventilation holes.
Height and vertical linearity controls located at the
rear panel are for special adjustments by qualified
personnel only.
Do not install the unit in an extremely hot or
humid place or in a place subject to excessive
dust, mechanical vibration.
The unit is not designed to be waterproof.
Exposure to rain or water may damage the unit.
Clean the unit with a slightly damp soft cloth.
Use a mild household detergent. Never use
strong solvents such as thinner or benzine as
they might damage the finish of the unit.
Retain the original carton and packing
materials for safe transport of this unit in the
future.
Safety ----------------------------------------- Installation -----------------------------------
Cleaning --------------------------------------
PRECAUTIONS
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR
MOISTURE. DO NOT INSERT ANY METALLIC OBJECTS THROUGH THE VENTILATION GRILLS OR
OTHER OPENINGS ON THE EQUIPMENT.

- iii -
FCC INFORMATION : THIS EQUIPMENT HAS BEEN TESTED
AND FOUND TO COMPLY WITH THE LIMITS FOR A CLASS A DIGITAL
DEVICE, PURSUANT TO PART 15 OF THE FCC RULES. THESE
LIMITS ARE DESIGNED TO PROVIDE REASONABLE PROTECTION
AGAINST HARMFUL INTERFERENCE WHEN THE EQUIPMENT IS
OPERATED IN A COMMERCIAL ENVIRONMENT. THIS EQUIPMENT
GENERATES, USES, AND CAN RADIATE RADIO FREQUENCY
ENERGY AND IF NOT INSTALLED AND USED IN ACCORDANCE WITH
THE INSTRUCTION MANUAL, MAY CAUSE HARMFUL INTERFERENCE
TO RADIO COMMUNICATIONS. OPERATION OF THIS EQUIPMENT IN
A RESIDENTIAL AREA IS LIKELY TO CAUSE HARMFUL
INTERFERENCE IN WHICH CASE THE USER WILL BE REQUIRED TO
CORRECT THE INTERFERENCE AT HIS OWN EXPENSE.
CAUTION : CHANGES OR MODIFICATIONS NOT EXPRESSLY
APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE
COULD VOID THE USER'S AUTHORITY TO OPERATE THE EQUIPMENT.
THIS CLASS A DIGITAL APPARATUS COMPLIES WITH CANADIAN
ICES-003.
NORME NMB-003 DU CANADA.
WARNING
THIS IS A CLASS A PRODUCT. IN A DOMESTIC ENVIRONMENT THIS
PRODUCT MAY CAUSE RADIO INTERFERENCE IN WHICH CASE
THE USER MAY BE REQUIRED TO TAKE ADEQUATE MEASURES.
CE COMPLIANCE STATEMENT
FCC COMPLIANCE STATEMENT

- iv -
IMPORTANT SAFEGUARDS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the
manufacturer's instructions.
8. Do not install near any heat sources such as radiators, heat
registers, stoves, or other apparatus (including amplifiers) that
product heat..
9. Do not defeat the safety purpose of the polarized or grounding-type
Plug. A polarized plug has two blades with one wider than the other.
A grounding type plug has two blades and a third grounding prong.
The wide blade or the third prong are provided for your safety. If the
provided plug does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the point where
exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Unplug this apparatus during lightning storms or when unused for
long periods of time.
13. Refer all servicing to qualified service personnel. Servicing is
required when the apparatus has been damaged in any way, such
as power-supply cord or plug is damaged, liquid has been spilled or
objects have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally, or has been
dropped.
14. CAUTION - THESE SERVICING INSTRUCTIONS ARE FOR USE
BY QUALIFIED SERVICE PERSONNEL ONLY. TO REDUCE THE
RISK OF ELECTRIC SHOCK DO NOT PERFORM ANY SERVICING
OTHER THAN THAT CONTAINED IN THE OPERATING
INSTRUCTIONS UNLESS YOU ARE QUALIFIED TO DO SO.
15. Use Certified/Listed Class 2 power source only.
thy

INTRODUCTION 1
CONTENTS OF PACKAGE 1
CAMERA CONNECTIONS 2
WALL BRACKET MOUNTING 2
CAMERA OVERVIEW 3
STRUCTURE OF THE SETUP MENU 4
CONTROL AND CONNECTIONS/DAY&NIGHT I/O/
ALARM OUT TERMINALS 8
WIRING DIAGRAM 9
HOUSING KIT SPECIFICATIONS 10
CAMERA SPECIFICATIONS 11
CAMERA ADJUSTMENT 3
- v -
TABLE OF CONTENTS

- 1 -
The camera provides high-quality images using SONY Wide Dynamic 1/3" CCD and digital
signal processing LSIs.
Features:
1/3" Super HAD Double Scan CCD for an image of high sensitivity
Wide Dynamic Range(WDR)
Excellent picture quality
600 lines(Color), 700 lines(B/W) of resolution
0.5 Lux(Color), 0.04 Lux(B/W), 0.001Lux(Low-shutter)@ F1.2 Sensitivity
Auto electronic shutter [1/60(1/50) ~ 1/100,000] and manual electronic shutter modes
OSD (On Screen Display)
Auto and manual white balance modes
Selectable BLC Zone
Day&Night (Auto/Manual, FILTER DLY)
Privacy Zone 16point, Motion Detection 4 Point
SHARPNESS, D-ZOOM, NEGA/POSI, MIRROR, V FLIP, ROTATION, FREEZE
AGC (Auto Gain Control)
RS485 CONTROL
Internal/AC line lock
Built-in 5-60mm or 2.8-12mm Vari-focal DC iris Lens.
Operates in 12VDC or 24VAC
Use Certified / Listed Class 2 power source only.
INTRODUCTION
IMPORTANT : The user of this camera is responsible for
checking and complying with local, state, and federal laws
and statutes concerning the recording and monitoring of
audio signals.
Installation of the camera must be performed by qualified service personnel in accordance
with all local and national electrical and mechanical codes.
Carefully remove the color camera and its accessories from the carton
and verify that they were not damaged in shipment.
The contents of the package includes:
1. CAMERA HOUSING KIT
2. This manual
3. L-wrench (5mm) --------------- 1ea
(2.5mm) ------------- 1ea
4. ANCHOR (5mm) --------------- 4ea
CONTENTS OF PACKAGE

- 2 -
CAMERA CONNECTIONS
2
1
REMINDER:
Never aim the
camera directly
into the sun.
1. Color Lead Wire & Color Display Label
2. Video : BNC connector used to connect the camera to a monitor, switcher, etc.
COLOR
BLACK
RED
BLUE
BROWN
DESCRIPTION
AC24V
AC24V
RS485(-)
RS485(+)
COLOR
BLACK
WHITE
ORANGE
BROWN
DESCRIPTION
DC12V
DC12V
RS485(-)
RS485(+)
1. Use fasteners of appropriate size and type to attach the bracket to the wall surface.
Position the housing so that it allow for viewing of the selected area.
2. Adjust the movable arm of the wall bracket to attain the desired position. One it is in place,
tighten the bolt located at the pivot point of the movable arm.
3. If you want to pull out the relevant cable, remove the knockout on the wall bracket mounting.
1
2
3
WALL BRACKET MOUNTING

- 3 -
CAMERA
CAM 001
Camera title.
Status of the dc level.
Camera ID.
CAMERA ADJUSTMENT
OSD MAIN SCREEN
DC LEVEL
CAMERA OVERVIEW
REAR VIEW
1
2
3
4
5
6
7
Left Button
Up Button
Enter Button
Right Button
Down Button
Day / Night External I/O
ALARM OUT
RS - 485
Power Indicator
Video Out Connector (BNC)
8
9
UTP or BNC Transformation Switch
(option)
Terminal
Block
1
23 4
5
6
7
10 8
9
10 AC/DC Compatible Input Terminal

STRUCTURE OF THE SETUP MENU
<MAIN MENU>
WB
AE
BLC / WDR
MOTION DET
PRIVACY
SPECIAL
EFFECT
CAM SET
END EXIT
<WB MENU>
MODE
R GAIN
B GAIN
END
<AE MENU>
LENS
MODE
SHUTTER
AGC
DC LEVEL, VIDEO LEVEL
(BRIGHTNESS)
FLICKERLESS
LOW SHUTTER
MAX LOW-SHUT
END
< WDR MENU>BLC/
END
BLC MODE
WDR MODE
L- LEVEL
S-LEVEL
<MOTION DET MENU>
AREA SEL
FUNCTION
DEFAULT
ADJ TOP / LEFT
ADJ BOT / RIGHT
SENSITIVITY
END
<PRIVACY MENU>
MASK SEL
MASKING
DEFAULT
ADJ TOP / LEFT
ADJ BOT / RIGHT
M COLOR
END
<SPECIAL MENU>
SYNC
PHASE
DN MODE
DN DELAY
END
<EFFECT MENU>
SHARPNESS
D-ZOOM
NEGA / POSI
D EFFECT
FREEZE
END
<CAM SET MENU>
CAM ID
BPS
PROTOCOL
DISP MODE
DISP ITEM
TITLE
SAVE
END
- 4 -

- 5 -
<WB>
Press the MENU button to access the "WB" mode.
1) MODE
Gain manually.
2) R GAIN A R-GAIN value.(0~255)
Can be adjusted while in manual mode.
O O
- AWB Set the color temperature 2500 K to 9500 K
- WAWB Wide range auto white balance mode.
O
- INDOOR Set the color temperature to 3200 K
O
- OUTDOOR Set the color temperature to 6300 K
- MANUAL Manual mode. User can change R and B
djust
3) B GAIN Adjust B-GAIN value.(0~255)
Can be adjusted while in manual mode.
<AE>
1) LENS
2) MODE
- AUTO Auto Exposure mode.
- SHUTTER Manual Shutter mode.
DC, Video, Manual Lens selected.
3) SHUTTER Select the shutter mode.(1/60(50) ~ 1/100,000 sec)
Can be changed while in shutter mode.
4) AGC Auto gain control ON/OFF
5) DC LEVEL / BRIGHTNESS
- DC LEVEL Adjust DC level (0 ~ 255)
Can be adjusted while in dc lens mode.
- VIDEO LEVEL Adjust VIDEO level (0 ~ 255)
Can be adjusted while in video lens mode.
- BRIGHTNESS Adjust BRIGHTNESS level (0 ~ 255)
Can be adjusted while in manual lens mode.
6) FLICKERLESS Removes screen flickering caused by discordance of
freguency and lighting.
7) LOW SHUTTER Use under very low light condition for full color surveillance.
8) MAX LOW-SHUT Select maximum Low-Shutter value. (x2 ~ x256)
Press the MENU button to access the "AE” mode.
< WDR>BLC/
Press the MENU button to access the " WDR" mode.BLC/
1) BLC MODE Sharpens subjects with backlight.
(OFF / CENTER / LEFT )TOP / BOTTOM / RIGHT /
2) WDR MODE Wide dynamic range ON/OFF
L- LEVEL Can be adjust long-time WDR level (0~200)
S- LEVEL Can be adjust short-time WDR level (0~200)

- 6 -
<PRIVACY>
Press the MENU button to access the "PRIVACY" mode.
1) MASK SEL Select MASK area number.
2) MASKING Select MASK ON/OFF
default.
boundary
with boundary
6) M COLOR Select MASK color. (WHITE/GRAY/BLACK)
3) DEFAULT Set MASK area as
4) ADJ TOP/LEFT Adjust the location of the MASK area with TOP
and LEFT.(MASK 1~16)
5) ADJ BOT/RIGHT Adjust the location of the MASK area
BOTTOM and RIGHT. (MASK 1~16)
<SPECIAL>
Press the MENU button to access the "SPECIAL" mode.
1) SYNC Select Internal or Line Lock mode.
-INT This mode is necessary for using the internal synchronization.
-L/L This mode is necessary for the operation of multi camera because
it synchronizes the camera phase by using the external signal
(AC Signal).
-AUTO Filter operates automatically according to brightness.
-COLOR The camera outputs the video image only in color.
-BW The camera outputs the video image only in black and white.
-EXT This menu automatically converts the COLOR Mode into the BW
Mode or vice versa depending on illumination with an external
sensor.
4) DN DELAY Adjust the working time of the filter when D&N operated.
(05sec / 10sec / 20sec)
2) PHASE Sync phase is adjustable in line lock mode.
3) DN MODE
<EFFECT>
Press the MENU button to access the "EFFECT" mode.
1) SHARPNESS Can be adjusted SHARPNESS of outlines.(0~15)
5) FREEZE Select the real or still mode.
2) D-ZOOM Digital Zoom ON / OFF
3) NEGA / POSI Select the negative or positive mode.
4) D EFFECT Reverse the screen in 3 modes selection.
(OFF / MIRROR / V FLIP / ROTATION)
<MOTION DET>
Press the MENU button to access the "MOTION DET" mode.
1) AREA SEL Select MD area number.
2) FUNCTION Select MD ON/OFF
with boundary
6) SENSITIVITY Adjust sensitivity of MD area.(1~255)
3) DEFAULT Set MD area as default.
4) ADJ TOP/LEFT Adjust the location of the MD area with boundary TOP and
LEFT.(MD 1~4)
5) ADJ BOT/RIGHT Adjust the location of the MD area BOTTOM
and RIGHT.(MD 1~4)

- 7 -
1) CAM ID Select the camera ID. (001 ~ 255)
2) BPS Select serial communication speed.(2400 / 4800 / 9600 / 19200)
3) PROTOCOL Select operating protocol.
COMMAND : Camera controlled by RS-232C command.
FASTRAX : Fastrax protocol.
PELCO-D : Pelco-D protocol.
PELCO-P : Pelco-P protocol.
4) DISP MODE On screen display is ON/OFF
5) DISP ITEM
-DISP0 Display title and camera ID.
-DISP1 Display title, camera ID and DC Level
6) TITLE
7) SAVE Save preset parameters of CAM SET MENU.
< >CAM SET
CMD
TITLE
<TITLE MENU>
B
C
A
A. TITLE
B. Character Table
C. Command Line
: Move to left
: Move to right
< : Erase a left character
> : Erase a right character
S : Save title
E : End
Press the MENU button to access the "CAM SET” mode.
<END>
1) DEFAULT & EXIT Set parameters as factory setting and terminate the MAIN MENU.
2) SAVE & EXIT Save the changed preset parameter and terminate the MAIN MENU.
3) EXIT Terminate the MAIN MENU without saving parameters.
Press the MENU button to access the "END” mode.

CONTROL AND CONNECTIONS/DAY&NIGHT
I/O / ALARM OUT TERMINALS
1) CAMERA CONTROL
Remote Control through keyboard controller or DVR.
7 PIN : RS 485+
8 PIN : RS 485-
2) DAY&NIGHT I/O Terminals
To select Day/Night mode using external equipment, connect control lines
to the appropriate terminals.
DAY&NIGHT OUTPUT (4pin)
It is the function that can turn on external IR LED Lamp by detecting the sensitivity on
the AGC level when the D&N mode is set "AUTO" on the OSD menu of the camera.
DAY&NIGHT EXTERNAL INPUT (3pin)
It is the function that can be switched to DAY Mode or NIGHT Mode by receiving the
D&N on/off signal from external light sensor or IR LED LAMP. When D&N Mode is set
"External" on the OSD menu of the camera.
3) ALARM OUT (6pin)
Motion detection signals are output through this port. (On High (5V))
1 2 3 4 5
TP VIDEO OUTPUT D&N I/O
OUT
COM
IN
- 8 -
4
5
DAY&NIGHT OUTPUT
COM
5V/10mA : IR LED ON(NIGHT)
0V : IR LED OFF(DAY)
5
3
COM
DAY&NIGHT INPUT
Open contact : DAY
Close contact : NIGHT
GND
6
ALARM
OUT
7 8
RS 485+(RX)
RS-485
RS 485-(TX)
CLASS 2
+ DC 12V -
~ AC 24V ~
This terminal accepts a DC12V or AC24V power
source from a DC12V or AC24V ac +/-10% 60/50Hz +/- 1Hz.
Use Certified/Listed Class 2 power supply only.
4) POWER INPUT TERMINAL
5) VIDEO OUT CONNECTOR
BNC : This BNC connector provides a 1.0Vp-p/75 ohms composite video Signal.
UTP : Unshielded Twisted Pair video Transmission for effective installation.(option)
1PIN : TP VIDEO OUTPUT
2PIN : TP VIDEO OUTPUT

- 9 -
WIRING DIAGRAM
24Vac Out
to Heater
24Vac Power
Supply Output
24Vdc Out
to Blower
24Vac Power
Supply Input
Ground Ground
(B+)
(Ground)
J3
J6 J4 J5
J1
24 Vac
* HEATER AND BLOWER

- 10 -
HOUSING KIT SPECIFICATIONS
5.5(14)
2.5(6.4)
2.3(5.9)
20.5(52.02)
9.68(24.6)
Unit: inch(cm)
Camera Housing Window Size 2.5" W x 2.3" H (6.4cm x 5.9cm)
Camera Housing Construction Die-cast, extruded, and sheet aluminum
Camera Housing Finish Light-gray ployester powder coat
Wall Bracket Pan Adjustment 360
Wall Bracket Tilt Adjustment 70
Wall Bracket Locking Method 4 holes for fasteners of a suitable size & type.
Mount to a secure solid surface.
Total Dimension(WxHxL) 5.5" W x 9.68" H x 20.5" D
(14cm x 24.6cm x 52.02cm)
Total Weight 9.15Ib( 4.15kg)

CAMERA SPECIFICATIONS
Power source
Power consumption
Image sensor
Total number of pixels
Scanning system
Scanning frequency
Sync. system
Electronic shutter
Resolution
Min. illumination
2:1 interlace
15.734KHz(H) x 59.94Hz(V)
Internal / Line lock
1/60 ~ 1/100,000 sec.
600 TV Lines (COLOR), 700TV Lines (B/W)
0.5 Lux (COLOR), 0.04 Lux (B/W), 0.001 lux (Low-shutter)
50dB (AGC OFF)
Auto / Manual Shutter / Flicker less
AWB / Indoor / Outdoor / Manual / WAWB
1/60 ~ 1/100,000
Top / Bottom / Center / Right / Left / Off
On / Off (DISP0 / DISP1)
V-Flip, Rotation, Mirror, D&N, D-Zoom,
Nega/Posi, B/W, Freeze, Privacy Zone, MD
x128
795(H) x 596(V)
NTSC
811(H) x 508(V)
MODEL
S/N Ratio
Auto Exposure
White Balance
Shutter Speed
BLC
Display
Effect
WDR
F
U
N
C
T
I
O
N
POWER
15.625KHz(H) x 50Hz(V)
1/50 ~ 1/100,000 sec.
PAL
Power input
Lens mount
1/4''-20 UNC (top or bottom)
2-Pin Terminal block
4-Pin mini din jack (standard connection)
C/CS mount (Selected through back focus)
Mounting hole
Video output
Auto iris output
Operating temperature
Operating humidity
BNC , UTP(option)
7.0 Watts
Video output 1.0 Vp-p (75 ohm, composite)
Camera Control RS485(FastraxII, Pelco D, Pelco P), Tact switch
1/50 ~ 1/100,000
0 ~ 96% (non-condencing)
AGC Control AUTO
Title A ~ Z / 0 ~ 9
CAM ID 001 ~ 255
BPS 2400 / 4800 / 9600 / 19200
Brightness 0 ~255 steps
Sharpness 0 ~15 steps
Low Shutter x2 ~ x256 (13steps)
G
E
N
E
R
A
L
C
O
N
N
E
C
T
O
R
&
ETC. -10 C ~ +50 C
DC 12V / AC 24V 10%
1/3" SONY DS CCD
- 11 -
Blower Heater
Power Supply
Power Consumption
Blower ON
Blower OFF
Power Supply
Power Consumption
Heater ON
Heater OFF
24 Vac
3.4W
t C > 35C +/-3C
T F > 95F +/-5F
t C < 20C +/-3C
24 Vac
20W
t C < 5C +/- 3C
T F < 41F +/- 5F
t C > 15C +/- 3C
Lens 5-60mm F1.6 DC iris or 2.8-12mm F1.3 DC iris

50302656A
WDR Super High Resolution
Day and Night Color Camera
PRINTED IN KOREA