ADT Pulse OC810-ADT User manual

ADT Pulse®Interactive Solutions
OC810-ADT Wireless
Outdoor Day/Night Camera
Installation Guide

ADT Pulse®Interactive Solutions OC810-ADT Wireless Outdoor Day/Night Camera
Installation Guide
i
CHAPTER 1 INTRODUCTION ............................................................................................1
Overview .......................................................................................................................1
Features .................................................................................................................1
Physical Details –OC810-ADT Wireless Outdoor Day/Night Camera ...........2
Front Panel - Wireless Camera..........................................................................2
Rear Panel –Wireless Camera ..........................................................................3
Package Contents .......................................................................................................4
CHAPTER 2 BASIC SETUP .................................................................................................5
Adding the OC810-ADT Wireless Outdoor Day/Night Camera to the ADT
Security System...........................................................................................................5
PIR Video Motion Detection......................................................................................9
Enabling the Motion Detection via the ADT Security System................. 11
APPENDIX A SPECIFICATIONS ..................................................................................... 13
OC810-ADT Wireless Outdoor Day/Night Camera ......................................... 13
Regulatory Approvals .............................................................................................. 13
FCC Statement ..................................................................................................13
CE Approvals...................................................................................................... 14
License information available at www.ADT.com or by calling 800.ADT.ASAP.
CA ACO7155, 974443; PPO17232; FL EF0001121; LA F1639, F1407,
F1640; MA 172C; NY 12000305615; PA 090797;
MS 15019511
©2013 ADT LLC dba ADT Security Services. All rights reserved. ADT, the ADT
logo, 800 ADT.ASAP and the product/service names listed in this document are
marks and/or registered marks. Unauthorized use is strictly prohibited.
Document Version: 2.2

ADT Pulse®Interactive Solutions OC810-ADT Wireless Outdoor Day/Night Camera
Installation Guide
1
Chapter 1
Introduction
This Chapter provides details of the OC810-ADT Wireless Outdoor
Day/Night Camera features, components and capabilities.
Overview
The OC810-ADT Wireless Outdoor Day/Night Camera (hereinafter referred to as
the wireless camera) has an Integrated Microcomputer and a high quality digital
Image Sensor, enabling it to display high quality, live streaming video to your
web or mobile client over an 802.11n Wireless LAN.
Features
Standalone Design: The wireless camera is a standalone device which
requires a power source and a wireless connection to the ADT Pulse®
gateway.
Triple Video Support: The wireless camera can support H.264, MEPG4
and MJEPG video for different image compression.
Day/Night Switch: With the automatic day/night switching feature, the
wireless camera is able to view and record crisper images in the dark within
a 25 foot area.
Standard Compliance: The wireless camera complies with the
IEEE802.11n (DSSS) specifications for Wireless LANs.
Supports 802.11n Wireless Stations: The 802.11n Draft standard
provides for backward compatibility with the 802.11g wireless network.
Speeds up to 108Mbps: All speeds up to the 802.11n maximum of
108Mbps are supported.
Security Support:Full WEP (64/128 Bit), WPA and WPA2 Personal
standards are supported on the Wireless interface allowing advanced
encryption of wireless data.

ADT Pulse®Interactive Solutions OC810-ADT Wireless Outdoor Day/Night Camera
Installation Guide
2
Physical Details –OC810-ADT Wireless Outdoor
Day/Night Camera
Front Panel - Wireless Camera
Figure 1: Front Panel
1. Lens
No physical adjustment is required or possible for the lens,
but you should ensure that the lens cover remains clean.
Image quality is degraded if the lens cover is dirty or
smudged.
2. Power LED
On - Powered on.
Off - No power.
Blinking - The Power LED blinks during power up. (This can
take up to 20 seconds.)
3. Light Sensor
The Light Sensor detects luminance.
4. IR LEDs
The LEDs allow the camera to see images at night or in a
dark environment.

ADT Pulse®Interactive Solutions OC810-ADT Wireless Outdoor Day/Night Camera
Installation Guide
3
Rear Panel –Wireless Camera
Figure 2: Rear Panel
1. Antenna
The antenna is adjustable with best results typically obtained
with the antenna positioned vertically.
2. Power port
The supplied 12V power adapter plugs power to the wireless
camera’s power port.
IMPORTANT
DO NOT USE ANY POWER ADAPTER OTHER THAN
THE ONE SPECIFIED FOR THIS CAMERA. DOING SO
MAY DAMAGE THE WIRELESS CAMERA.
3. Ethernet port
The Ethernet port allows connectivity of the wireless camera
to your ADT Pulse gateway.
IMPORTANT
PLUGGING IN THE ETHERNET CABLE WILL DISABLE
THE WIRELESS INTERFACE. (ONLY ONE INTERFACE
CAN BE ACTIVE AT ANY TIME.)
THE ETHERNET CABLE SHOULD ONLY BE
CONNECTED OR DISCONNECTED WHEN THE
OUTDOOR DIGITAL CAMERA IS POWERED OFF.
ATTACHING OR DETACHING THE ETHERNET CABLE
WHILE THE CAMERA IS POWERED ON DOES NOT
SWITCH THE INTERFACE BETWEEN WIRED AND
WIRELESS.
DETACHING THE ETHERNET CABLE WHEN THE
OUTDOOR DIGITAL CAMERA IS POWERED ON WILL
DISCONNECT THE OUTDOOR DIGITAL CAMERA
FROM THE NETWORK.
4. Reset Button
When pressed and held for ten (10) seconds, the
communication configuration of the wireless camera will be
reset to the default manufacturer settings.

ADT Pulse®Interactive Solutions OC810-ADT Wireless Outdoor Day/Night Camera
Installation Guide
4
IMPORTANT
THE RESET BUTTON WILL RESET THE CAMERA
COMMUNICATION CONFIGURATION SETTINGS AND
SHOULD ONLY BE USED UNDER THE DIRECTION OF
ADT SUPPORT.
Package Contents
The following items are included:
1. OC810-ADT Wireless Outdoor Day/Night Camera
2. Antenna
3. Power Adapter
4. Ethernet Cable
5. Power Extension Cable (With water sealing cap)
6. Stand
7. Mounting Screws
8. Quick Installation Guide

ADT Pulse®Interactive Solutions OC810-ADT Wireless Outdoor Day/Night Camera
Installation Guide
5
Chapter 2
Basic Setup
This Chapter provides details of installing and configuring the OC810-ADT
Wireless Outdoor Day/Night Camera.
Adding the OC810-ADT Wireless Outdoor Day/Night
Camera to the ADT Security System
NOTE
The OC810-ADT wireless camera can only be added to a Pulse
system that supports video.
1. Open your web browser. In the address bar, type:
https://Portal.ADTPulse.com
2. Type your Username and Password, and then click the Sign In button.
3. Click the System tab, and then click the Manage Devices button.

ADT Pulse®Interactive Solutions OC810-ADT Wireless Outdoor Day/Night Camera
Installation Guide
6
4. Click Cameras.
5. Click the picture of the OC810 camera or select it from the drop-down list,
and then click the Continue button.

ADT Pulse®Interactive Solutions OC810-ADT Wireless Outdoor Day/Night Camera
Installation Guide
7
6. Assign the wireless camera a unique name (this is usually based on the
location of the wireless camera) in the space provided, and then type the
wireless camera’s MAC ID or Server Name.
7. Click the Continue button.
8. Attach the antenna to the wireless camera. To adjust the antenna, screw to
the rear mounting point and set the antenna to the upright position to
improve wireless reception.
9. Connect the wireless camera to the Device Port of the gateway using a
standard LAN cable.
10. Connect the supplied 12V power adapter to power up the wireless camera,
and then click the Continue button.
NOTE
The Power LED turns on briefly, and then starts blinking during
startup, which takes approximately 5 to 20 seconds. After
startup is completed, the Power LED should remain ON.

ADT Pulse®Interactive Solutions OC810-ADT Wireless Outdoor Day/Night Camera
Installation Guide
8
11. Once connected, click the Continue button.
12. Click the Finish button. The installation is complete.
13. Disconnect the wireless camera from the gateway and remove from
power. Assemble mounting bracket, and install camera in the final
location. Re-apply power. If the camera does not connect, use of the
ADT Wi-Fi extender, part # WN2RPADT-1ADNAS is recommended
and may improve connectivity.
For more information, refer to Physical Details –on Pages 2 and 3.