ADTRAN 834-5 User manual

Q
uick Star
t
Overview
The ADTRAN® 834-5 is a carrier-class Dual-Band Wi-Fi 5 Gigabit Ethernet router, built to deliver top-end Wi-Fi 5 performance, true gigabit routing
throughput, and advanced service delivery capabilities. This quick start describes how to install ADTRAN’s 834-5 Home Gateway Unit.
The 834-5 WiFi 5 Gigabit Router is an indoor gateway for delivering premium Gigabit services.
■“Installing the 834-5 Gateway” on page 2
■“Understanding the Status LEDs” on page 4
■“Safety and Regulatory” on page 5
Figure 1 illustrates the front and back of the 834-5 gateway.
Figure 1. Front and Back of the 834-5 Gateway (placeholder)
WARNING!
f
Read all warning, cautions, notes and installation instructions before installing or servicing this equipment.
f ATTENTION!
Lisez tous les avertissements et mises en garde avant l’installation de cet équipement ou la réalisation de toute opération de maintenance
f WARNING! f CAUTION! g NOTE
WARNING indicates a hazard which, if
not avoided, could result in death, injury
or serious property damage.
CAUTION indicates a hazard which, if not
avoided, could result in service interruption,
damage to the equipment, or minor property
damage.
NOTES inform the user of additional, but
important, information or features.
ADTRAN
834-5 Service Delivery Gateway
Wi-Fi 5 Gigabit Router
May 2021
617600021-13A
P/N: 17600021F1

2 617600139F1-13A
Features
The features of the 834-5 gateway include the following:
■1x Gigabit Ethernet (RJ-45) WAN interface
■ Subscriber interfaces
♦4x4 802.11ac @ 2.4GHz
♦ 4x4 802.11ac @ 5GHz
♦4x Gigabit Ethernet (RJ-45) LAN interfaces
♦1x USB 3.0 (Type A) Host port
Installing the 834-5 Gateway
The following are guidelines for basic installation of the 834-5.
Package Contents
■ ADTRAN’s 834-5 WiFi 5 Gigabit Router
■ 12V DC power adapter
Prior to Installation
Before installing the equipment, inspect the gateway. If damage has occurred during shipping, file a claim with the carrier, and then contact ADTRAN
Customer Support. For more information, refer to the product warranty available online at https://adtran/wp_support_warranty.
Required Tools
Standard technician tools and, if installing the gateway on a wall, a #2 Phillips-head screwdriver, are required for installing the 834-5.
Mounting Options
There are two options to install the 834-5: desktop and wall mount. Be sure to route and secure the fiber and cables in a manner that will prevent damage.
These options are described below.
Desktop Installation
The 834-5 can be placed on a desk or table. The following table shows the recommended minimum distance (in feet and meters) between the gateway
and household appliances to reduce interference.
NOTE
g
Refer to the national, state and local electrical codes for the requirements for power, grounding, wiring, and installation methods.
CAUTION!
f
The product is intended for indoor use only. Ethernet cables, and attached equipment are intended for use within the same building with
equipotential bonding, and not intended to be placed in separate buildings or structures. Failure to deploy as described could result in permanent
damage from lightning or other electrical events and voids the warranty. Furthermore, all connections from outside of the building, such as old
POTS wiring, must be disconnected prior to use.
Household Appliance Recommended Minimum Distance (in feet and meters)
Microwave ovens 30 feet / 9 meters
Baby monitor – analog 20 feet / 6 meters
Baby monitor – digital 40 feet / 12 meters
Cordless phone – analog 20 feet / 6 meters

617600139F1-13A 3
Wall Mount Installation
The 834-5 can be mounted on a wall. Wall Mount Kit (17600192F1) can be ordered for mounting the 834-5. Instructions are provided in the related
Quick Start Guide (617600192F1-13A).
Connecting the 834-5 Gateway
Figure 2 illustrates the installation (connection) options for the 834-5 gateway.
Figure 2. 834-5 Gateway Installation Options (placeholder)
The following subscriber connections are available on the rear of the 834-5:
■ 4x Gigabit Ethernet (RJ-45 Connectors) – LAN 1- 4 ports
■ 1x Gigabit Ethernet port (RJ-45 Connector) -WAN port
■ 4x4 802.11ax @ 2.4GHz
■ 4x4 802.11ax @ 5GHz
■ 1x USB 3.0 (Type A Connector) - port
To connect the subscriber Ethernet interfaces, refer to Figure 2 and insert a Category 5E (or better) RJ-45 cable into one of the LAN ports (labeled
LAN 1- 4) or the Gigabit Ethernet port (WAN) until there is an audible “click”.
Connecting the Power Supply
1. Connect the end of the power adapter to the Power port on the rear panel of the gateway
2. Plug other end of the power adapter into the wall outlet.
Cordless phone – digital 30 feet / 9 meters
Bluetooth devices 20 feet / 6 meters
ZigBee 20 feet / 6 meters
WARNING!
f
Ensure that the 834-5 does not come in contact with water or other liquids.
CAUTION!
f
Ensure that the 834-5 is not located in direct sunlight or next to any thermal obstructions.
Household Appliance Recommended Minimum Distance (in feet and meters)

4 617600139F1-13A
3. Confirm that the power is connected properly. The Power LED should be lit on the front of the gateway.
Resetting the Gateway
A reset button is available if the 834-5 needs to be rebooted. To reboot the 834-5, press the Reset button on the rear panel of the gateway for 5 seconds
or less. To reset the device to custom defaults, press the Reset button for 5 seconds or more.
Understanding the Status LEDs
The LEDs on the back panel of the 834-5 gateway enable you to monitor the device status. This section describes the three types of LEDs available on
the 834-5 gateway. See Figure 3 for details.
Figure 3. Status LEDs (placeholder)
2.4 GHz / 5 GHz Status LEDs
The 2.4 GHz and 5 GHz status LEDs indicate the state of the wireless connections on the gateway.
WPS Status LED
The WPS status LED indicates the status of WPS (Wi-Fi protected setup).
Product Specifications
Electrical
■ Power is provided by a 12V DC Power Adapter that is included with the 834-5. The power adapter operates from a power source of 100 to 240V AC,
50 - 60 Hz. The nominal output is 12V DC +\–5% with a maximum current rating of 4.0 Amps. For US and Canadian applications, a UL Listed limited
power source (LPS) is required. For deployment outside of North America, an LPS specifically approved for that country, such as a CE Mark, is
required.
NOTE
g
Alternately, the device may be powered by a supported third-party UPS which may be connected via 7-pin molex connector, labeled UPS.
LED Color State Description
2.4 GHz
5 GHz
Green On Wi-Fi radio is UP.
Flashing Wi-Fi radio is transferring data.
None Off Wi-Fi connection is DOWN.
LED Color State Description
WPS Green On WPS is enabled.
Flashing WPS is passing traffic.
None Off WPS is not active.
NOTE
g
It is strongly suggested that the power supply (a 5-foot (1.5 m) power cord) included with the 834-5 be connected to a surge suppressor device
which can have its own extension cable. The surge protection device should provide L-N, L-G, and N-G protection. It is also recommended that
the device contains a visual 'GOOD' indicator.

Environment
■ Operating Temperature: 32°F to 104°F (0°C to 40°C)
■ Storage Temperature: -40°F to 158°F (-40°C to 70°C)
■ Relative Humidity: 10 to 95 percent, non-condensing
Safety and Regulatory
This product meets the following compliance requirements:
■ UL /cUL Listed
■ FCC Part 15, Class B
■ ICES-003 (Class B)
■ IEC 62368-1
■ EN 62368-1, AS/NZS 60950.1
■ RoHS Compliant
This equipment contains no parts that can be serviced by the user.
Refer to the Safety and Regulator Notice for this product (P/N: 617600021F1-17) for detailed safety and regulatory information.
Consultez l'avis sur la sécurité et la conformité à la réglementation pour ce produit (P/N: 617600021F1-17) pour obtenir des renseignements détaillés sur
la sécurité et la réglementation.
Ausführliche Sicherheits- und regulatorische Informationen sind in der Konformitätserklärung zur Sicherheit und Einhaltung von Normen zu diesem
Produkt (P/N: 617600021F1-17) aufgeführt.
NOTE
g
Changes or modifications not expressly approved by ADTRAN will void the warranty.
Documentation for ADTRAN Network Solutions products is
available for viewing and download directly from the ADTRAN
Support Community website.
Go to: https://supportcommunity.adtran.com
ADTRAN offers training courses on our products, including
customized training and courses taught at our facilities or at
customer sites.
For inquiries, go to: http://adtran.com/training
Access additional safety information and product documentation using the QR
code or website.
https://supportcommunity.adtran.com
Warranty: ADTRAN will replace or repair this product within the warranty period if it does not
meet its published specifications or fails while in service. Warranty information can be
found online at www.adtran.com/warranty.
Trademarks: Brand names and product names included in this document are trademarks,
registered trademarks, or trade names of their respective holders.
Copyright © 2021 ADTRAN, Inc. All Rights Reserved.
ADTRAN CUSTOMER CARE:
From within the U.S. 1.888.423.8726
From outside the U.S. +1 256.963.8716
PRICING AND AVAILABILITY 1.800.827.0807
617600021F1-13A

Copyright © 2021ADTRAN, Inc.
CX Documentation
Approval Stamp Sheet
Document Number: 617600137F1-17A
Document Name: 865-v6 Gateway Compliance Note
Date of Review: May 3, 2021
Reviewer Statement: I have read and reviewed this document and give it my
approval for release.
Approval Signatures: Use the Approved stamp from the Dynamic stamps list.
Product Management:
Kurt Diekemper
David LaCagnina
Engineering Management:
Jay Cohen
Mirko Lindner
Writer: Kathleen D'Adamo
Technical Support:
Evan Hudson
TSSE:
Gaurav Negi
Compliance:
Larry Bell
Applications Engineering:(Optional)
Training:
(Optional)
DVT/QA:
Editor/Peer Review: Victoria Hannum

Safety and Regulatory Notice
Sécuritéet Avis de réglementation
Sicherheitsvorschriften und -hinweise
f CAUTION!
■Connect the DC power inputs to an approved Limited Power Source (LPS) power supply ONLY.
■This equipment contains no parts that can be serviced by the user.
■This product is intended to operate in ambient temperatures up to 40°C.
■It is recommended that an external AC Surge Protection Device be installed at the AC input connection to the local AC-Powered product. The Surge
Protection device should provide L-N, L-G, and N-G protection. It is also recommended that the device contains a visual 'GOOD' indicator.
■ The product is intended for indoor use only. Ethernet, Voice, and attached equipment are intended for use within the same building with equipotential
bonding, and not intended to be placed in separate buildings or structures. Failure to deploy as described could result in permanent damage from
lightning or other electrical events and voids the warranty.
g NOTES
This product meets the following compliance requirements:
■ This equipment contains no parts that can be serviced by the user.
■ This product meets EU RoHS Directive. Refer to www.adtran.com/environmental for further information on RoHS/WEEE.
■ This product is UL Listed to the applicable UL/CSA Standards.
■ This product has also been evaluated to applicable international standards including CE and RCM marking.
■ The AC branch circuit socket-outlet must be installed near the equipment and must be easily accessible.
■ The RJ-45 jacks are not used for telephone line connection.
This radio transmitter (IC: 2250A-W338E0) has been approved by Industry Canada to operate with the antenna types listed below. Antenna types not
included in this list are strictly prohibited for use with this device.
■ Dynamic Frequency Selection (DFS) for devices operating in the bands 5250 - 5350 MHz, 5470 - 5600 MHz and 5650 - 5725 MHz.
f WARNING! fAVERTISSEMENT! fWARNUNG!
■Read all warnings, cautions, notes,
and installation instructions before
installing or servicing this equipment.
■Lisez toutes les mentions de danger et
de prudence et les remarques, ainsi
que la notice d'installation, avant
d'effectuer l'installation ou l'entretien
de cet équipement.
■Lesen Sie alle Warnungen,
Gefahrenhinweise, Anmerkungen und
Installationsanweisungen bevor Sie dieses
Gerät installieren oder warten.
■Refer to the national, state, and local
electrical codes for the requirements
for power, grounding, wiring, and
installation methods.
■Consultez les Codes de l'électricité -
national, régional et local - pour
connaitre les exigences concernant
l'alimentation, la mise à terre, le
câblage, et les méthodes d'installation.
■Beziehen Sie sich auf die in den nationalen,
bundesstaatlichen und lokalen elektrischen
Vorschriften festgelegten Anforderungen an
Stromversorgung, Erdung, Verkabelung und
Installationsmethoden.
■This product may be powered by
multiple sources. Disconnect all
sources of power prior to servicing.
■Ce produit peut être alimenté par des
sources multiples. Débranchez toutes
les sources d'énergie avant l'entretien.
■Dieses Produkt kann durch mehrere Quellen
versorgt werden. Trennen Sie alle
Stromquellen vor der Wartung.
WiFi 5 Gigabit Router
July 2021
617600021F1-17a
P/N: 17600021F1
834-5 Service Delivery Gateway

2 617600021F1-17a
Rev A
■ The device for the band 5150-5250 MHz is only for indoor usage to reduce potential for harmful interference to co-channel mobile satellite systems.
■ Users should also be advised that high-power radars are allocated as primary users (i.e. priority users) of the bands 5250-5350 MHz and 5650- 5850
MHz and that these radars could cause interference and/or damage to LE-LAN devices.
■ The maximum antenna gain permitted for devices in the bands 5250-5350 MHz and 5470-5725 MHz shall be such that the equipment still complies
with the equivalent isotropically radiated power (EIRP). limit.
■ The maximum antenna gain permitted for devices in the band 5725-5850 MHz shall be such that the equipment still complies with the EIRP limits
specified for point-to-point and non-point-to-point operation as appropriate.
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-
exempt RSS(s). Operation is subject to the following two conditions:
1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement économique
Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes :
1. L’appareil ne doit pas produire de brouillage;
2. L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
Regulatory Compliance Information
This section includes user requirements for operating this product in accordance with National laws for usage of radio spectrum and operation of radio
devices. Failure of the end-user to comply with the applicable requirements may result in unlawful operation and adverse action against the end-user by
the applicable National regulatory authority.
This product's firmware limits operation to only the channels allowed in a particular Region or Country. Therefore, all options described in this user's guide
may not be available in your version of the product.
Europe – EU Declaration of Conformity
Products bearing the marking comply with the following EU directives:
■ EMC Directive 2014/30/EU
■ Low Voltage Directive 2014/35/EU
■ WEEE Directive reference: 2012/19/EU
If this product has telecommunications functionality, it also complies with the requirements of the following EU Directive:
■ RED 2014/53/EU
Compliance with these directives implies conformity to harmonized European standards that are noted in the EU Declaration of Conformity.
For indoor use only. Valid in all EU member states, EFTA states, and Switzerland.
This device may not be used for setting up outdoor radio links in France and in some areas the RF output power may be limited to 10 mW EIRP in the
frequency range of 2454 - 2483.5 MHz. For detailed information the end-user should contact the national spectrum authority in France.
FCC Requirements for Operation in the United States
FCC Information to User
This product does not contain any user serviceable components and is to be used with approved antennas only. Any product changes or modifications will
invalidate all applicable regulatory certifications and approvals.
FCC Guidelines for Human Exposure
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated
with minimum distance of 20 cm between the radiator and your body.
This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance with FCC
multi-transmitter product procedures.
FCC Declaration of Conformity
We, ADTRAN, Inc., 901 Explorer Blvd, Huntsville, AL 35806, declare under our sole responsibility that the 865-v6 complies with Part 15 Subpart B of FCC
CFR47 Rules. Operation is subject to the following two conditions:
■ This device may not cause harmful interference, and
■ This device must accept any interference received, including interference that may cause undesired operation.
FCC Radio Frequency Interference Warnings & Instructions
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:

Copyright © 2021 ADTRAN, Inc. All Rights Reserved.
ADTRAN CUSTOMER CARE:
From within the U.S. 1.800.726.8663
From outside the U.S. +1 256.963.8716
PRICING AND AVAILABILITY 1.800.827.0807
*617600021F1-17a*
■ Reorient or relocate the receiving antenna.
■ Increase the separation between the equipment and receiver.
■ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
■ Consult the dealer or an experienced radio/TV technician for help.
CAN ICES-3(B)/NMB-3(B)
Canadian Department of Communications Radio Interference Regulations
This digital apparatus (Wi-Fi 6 GPON HGU Model 814-v6) does not exceed the Class B limits for radio-noise emissions from digital apparatus as set out
in the Radio Interference Regulations of the Canadian Department of Communications.
Industry Canada
This device complies with RSS-247 of the Industry Canada Rules.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.
IMPORTANT NOTE: Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body.
NOTE IMPORTANTE: Déclaration d'exposition aux radiations:
Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet équipement doit être
installé et utilisé avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps.
CAUTION!
f
(i) the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile
satellite systems;
(ii) the maximum antenna gain permitted for devices in the bands 5250-5350 MHz and 5470-5725 MHz shall be such that the equipment still complies
with the e.i.r.p. limit;
(iii) the maximum antenna gain permitted for devices in the band 5725-5850 MHz shall be such that the equipment still complies with the e.i.r.p. limits
specified for point-to-point and non-point-to-point operation as appropriate; and
(iv) the worst-case tilt angle(s) necessary to remain compliant with the e.i.r.p. elevation mask requirement set forth in Section 6.2.2(3) shall be clearly
indicated.
(v) Users should also be advised that high-power radars are allocated as primary users (i.e. priority users) of the bands 5250-5350 MHz and 5650-
5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices.
f ATTENTION!
i) les dispositifs fonctionnant dans la bande 5150-5250MHz sont réservés uniquement pour une utilisation à l’intérieur afin de réduire les risques de
brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux;
(ii) le gain maximal d'antenne permis pour les dispositifs utilisant les bandes de 5250 à 5350MHz et de 5470 à 5725MHz doit être conforme à la limite
de la p.i.r.e;
(iii) le gain maximal d'antenne permis (pour les dispositifs utilisant la bande de 5725 à 5850MHz) doit être conforme à la limite de la p.i.r.e. spécifiée
pour l'exploitation point à point et l’exploitation non point à point, selon le cas;
(iv) les pires angles d’inclinaison nécessaires pour rester conforme à l’exigence de la p.i.r.e. applicable au masque d’élévation, et énoncée à la section
6.2.2 3), doivent être clairement indiqués.
Installation Instructions:
Refer to the Quick Start or Job Aid for this
product (P/N: 61181501G8-13) for detailed
installation instructions.
Notice d'installation :
Rapportez-vous au Guide de prise en main,
ou à L'Aide-mémoire pour ce produit (Code
article 61181501G8-13) pour des consignes
d'installation détaillées.
Installationsanweisungen:
Genaue Installationsanweisungen finden Sie
in der Schnellstart- oder Auftragshilfe für
dieses Produkt (P/N:61181501G8-13).