ADTRAN 1200422L1 User manual

Quick Start Guide, 61200422L1-13F, November 2008 Copyright © 2008 ADTRAN, Inc., All Rights Reserved.
For more detailed documentation, visit us online at www.adtran.com.
Quick Start Guide
®
NetVanta 300 Series Router P/N 1200422L1, 1200423L1, 1200426E1/L1
GETTING STARTED
Two configuration methods are available for your NetVanta router:
• Web-based graphical user interface (GUI)
• AOS command line interface (CLI)
The GUI lets you configure the main unit settings and provides online guidance and explanations
for each setting. However, using the AOS CLI may be necessary for more advanced
configurations.
ACCESS THE GUI
You may access the GUI from any Web browser on your network by following these steps:
1. Connect the router to your PC using one of the ETHERNET ports on the back of the unit.
2. During bootup, your PC will obtain an IP address from the NetVanta 300 Series unit’s DHCP
server. By default, both the DHCP and HTTP servers are enabled.
3. Enter the unit’s IP address in your browser address line. The default IP address is 10.10.10.1.
4. You will then be prompted for the user name and password (the default settings are admin
and password).
5. The initial GUI screen appears.
6. Select Getting Started in the System menu on the left side of your screen and follow the
online instructions.
For security purposes, you should set up an admin password
immediately. Use the Passwords page of the GUI to change this
password.
By default, the NetVanta unit comes with an ADSL and an asynchronous
transfer mode (ATM) port already configured and enabled. The service
provider should provide a PVC (VPI/VCI) number that will be used to
configure the ATM PVC.
CONFIGURE THE ATM PVC
1. Select the Getting Started link under the System menu. This brings up a side bar page.
2. Select Step 1 - Configure the Public Interface at the top of the side bar page to open the
ATM PVC page.
3. Enter the PVC number and select an Interface Mode. Usually this is PPP or PPPoE;
however, if IP routing is chosen, you will need to enter an IP address.
4. Select Apply. If PPP or PPPoE is selected as the Interface Mode, you will be taken to the
PPP page after selecting Apply. Here you will need to select the type of authentication
needed, authentication passwords, and the Address Type. In most cases, you will want the
Address Type to be Negotiated. Select Apply when all the information is complete.
ACCESS THE CLI
If needed, you can access the AOS CLI via a Telnet session.
1. Telnet to the unit’s IP address. The default IP address is 10.10.10.1.
2. You will then be prompted for the user name and password (the default settings are admin
and password).
3. Enter enable at the >prompt.
4. Enter the enable password when prompted. The default password is password.
FACTORY DEFAULT SWITCH
• If the factory default switch (shown in the back panel illustrations on the next page) is pressed
during bootup, the unit will stay in bootstrap mode. Since the unit has no serial port, Telnet
has been built into the boot code. The default IP address is 10.10.10.1.
• If the factory default switch is pressed and held for 5 seconds after boot, the ETHERNET
interface on the NetVanta 340 (or the VLAN 1 interface on the NetVanta 344) will default to
10.10.10.1 and all access policies will be removed from that interface.
• If the factory default switch is pressed and held for 30 seconds, a default configuration will
overwrite your existing configuration and reboot the unit.
The default switch must be pressed WHILE the power light is flashing
green. Do not press the default switch BEFORE the power light is
flashing green, as this will cause boot to be missed.

Quick Start Guide, 61200422L1-13F, November 2008 Copyright © 2008 ADTRAN, Inc., All Rights Reserved.
For more detailed documentation, visit us online at www.adtran.com.
Quick Start Guide
®
NetVanta 300 Series Router P/N 1200422L1, 1200423L1, 1200426E1/L1
ADSL CONNECTOR PINOUTS
Pin Name Description
1, 2 — Unused
3 T ADSL Tip
4 R ADSL Ring
5, 6 — Unused
CONFIGURE YOUR APPLICATION
More detailed documentation for configuring your ADTRAN unit is provided online at
www.adtran.com. For more detail on hardware setup, refer to the appropriate hardware installation
guide. For more detail on configuring your system, refer to the AOS Command Reference Guide,
configuration guides, and technical support notes.
ETHERNET PINOUTS
Pin Name Description
1 TX1 Transmit Positive
2 TX2 Transmit Negative
3 RX1 Receive Positive
4, 5 — Unused
6 RX2 Receive Negative
7, 8 — Unused
Important: For additional details on product features, specifications,
installation, and safety, refer to the appropriate hardware installation
guide available online at www.adtran.com.
NetVanta 340 Rear Panel Layout
NetVanta 344 Rear Panel Layout