Advance Tabco NS Series User manual

Installation Instructions
for Drawers
TA-90 Drawer Adapter
Contents:
(2) Drawer Angles
(4) Self Tapping Screws
Required Tools:
Drill Motor
1/8” Drill Bit
Open End Wrench or Socket
Step 1:
Turn table upside down.
Step 2:
Position drawer angles 21 5/8” O.D. apart, Drawer angle slotted hole
to be located 5” from front edge of table. (Illustration 1) mark holes.
21 5/8”
O.D.
Illustration 1
Step 3:
Drill 1/8” holes at four locations and use self tapping screws
provided to mount angle. (Illustration 2)
5”
Step 4:
Refer to mounting procedure for the appropriate drawer.
(see inner page)
CHECK FOR CONCEALED DAMAGE
FILE CLAIM WITH DELIVERING FREIGHT CARRIER
Drawers manufactured by ADVANCE TABCO are designed and
constructed for storage. Applications may include storage of
flatware, small utensils, etc. ADVANCE TABCO does not
recommend product use for activities employing harsh and active
chemicals. Please consult factory regarding unusual applications.
DRW-3/00
Edgewood, New York 11717
Illustration 2

FS & FG Series Drawers
Illustration 1
Illustration 2
NS Series Drawers
Contents: Tools Required:
(1) Outer Drawer Body (2) 7/16 open end wrenches
(1) Inner Drawer Liner
(1) Drawer Pan Insert
(2) NSF Drawer Slide
(4) 1/4 - 20 x 1/2” Bolts with Nuts
Step 1:
Remove drawer Pan insert. Remove inner Liner. Remove NSF
drawer slide. (Illustration 1)
Illustration 1
Step 2:
Mount outer drawer body
to underside of table using
1/4 - 20 x 1/2” bolts and
nuts provided. NOTE:
Outer drawer body mounts
between drawer angles
(Illustration 2) NOTE: For
30” & wider worktables,
align front mounting hole of
outer drawer body with slotted hole located 5” off roll edge.
Illustration 3
Step 3:
Pivot retainer clip up while pushing drawer body into slide.
Reposition clip as shown and tighten bolt. (Illustration 3)
Step 2:
Attach drawer retainer clip loosley to front hole of left drawer slide.
(Illustration 2)
Contents: Tools Required:
(1) Drawer Body (2) 7/16 open end wrenches
(2) Friction Drawer Slides
(4) 1/4 - 20 1/2” Bolts with Nuts
(1) Drawer Retainer Clip
Step 1:
Install friction slides underneath table top using 1/4 - 20 x 1/2”
bolts and nuts provided. NOTE: Drawer slide must be positioned
to inside of drawer angles. (Illustration 1)
Illustration 2
Step 3:
Install NSF drawer slides as shown in Illustration 3.
Step 4:
Extend drawer slide out towards front of table and install inner
drawer body by aligning bearing with notch in drawer slide.
(Illustration 4)
Illustration 3
Step 5:
Extend inner drawer body towards front
of table and install drawer insert.
(Illustration 5)
SS & GZ Series Drawers
Contents: Tools Required:
(1) Drawer Body (2) 7/16 open end wrenches
(2) Drawer Slides
(4) 1/4 - 20 x 1/2” Bolts with Nuts
Step 1:
Install roller bearing slides to underside of table using
1/4 - 20 x 1/2” bolt and nuts provided. NOTE: Drawer slide
must be positioned to inside of drawer angle. Alignment pin
must be positioned towards front of table (Illustration 1)
Illustration 4
Illustration 5
Illustration 1
Illustration 2
Step 3:
Position drawer body between drawer slides. Locate holes in
drawer body onto alignment pin. Install rubber sleeves onto
alignment pins. (Illustration 3)
Illustration 3
Step 2:
Fully extend drawer slides towards front of table and remove rubber
sleeves from alignment pins. (Illustration 2)