Advantech FWA-3240 Installation and operation manual

FWA-3240 Startup Manual 1
If you have any technical questions about the FWA-
3240 or any other Advantech products, please visit our
support website at:
http://www.advantech.com.tw/support
http://www.advantech.com.
For technical support and service, please visit our
support website at:
http://www.advantech.com/support
This manual is for the FWA-3240 series Rev. A
Part No. 2002324000
Print in China
1st Edition,
Nov 2008
Before installation, ensure that the following materials have
been received:
One FWA-3240 Internet Security Platform
One box of accessories
One warranty certificate
If any of these items are missing or damaged, please con-
tact your distributor or sales representative immediately.
Note: Acrobat Reader is required to view any PDF file.
Acrobat Reader can be downloaded at: www.
adobe.com/Products/acrobat/readstep2. html
(Acrobat is a trademark of Adobe)
Do not leave this equipment in an environment un-
conditioned where the storage temperature under 0°
C (32° F) or above 40° C (104° F), it may damage the
equipment.
The openings on the enclosure are for air convection
hence protect the equipment from overheating. DO NOT
COVER THE OPENINGS.
Make sure the voltage of the power source is correct
before connecting the equipment to the power outlet.
Place the power cord in a way that people can not
step on it. Do not place anything over the power cord.
The voltage and current rating of the cord should be
greater than the voltage and current rating marked on
the product.
•
•
•
1.
2.
3.
4.
FWA-3240 1U Rackmount Intel® Tolapai-based Plat-
form with 4 Front LAN Ports & LCD Display
Startup Manual
Standard SBC functions
CPU & Chipset: Intel EP80579 Integrated Processor
(Tolapai) supports 600/1066/1200 MHz processor
BIOS: Award™ 4Mbit Flash
FSB: 400/533 MHz
System memory: Up to 2GB memory capacity. One
DIMM socket supporting DDR2 SODIMM technology
memory. 200-pin DDR2-533, DDR2-667 and DDR2-800
can be used.
Note: Due to the inherent limitations of PC architecture,
the system may not fully detect 4 GB RAM when
4 GB RAM is installed.
CF Interface: JMicron (SATA to IDE bridge)
1 x CF socket on IDE 0 (Primary)
SATA Interface: 1 x 2.5” or 3.5” HDD bay Max. data
transfer rate at 150 MB/sec.
Keyboard/mouse Pin header: Supports standard PS/2
keyboard and mouse for debug and installation use.
USB 2.0: 2 x USB 2.0
Serial: 1 x RS-232 with RJ-45 connector
Ethernet interface
Interface: 4 x 10/100/1000 Base-T
Controller: Three GbE from Intel EP80579 Integrated
Processor + Marvell 88E1111 PHY, One GbE from Intel
82574, with bypass function
Mechanical and Enviromental
Dimensions(W x H x D): 426 x 44 x 236 mm (16.8” x
1.7” x 9.3”)
Power supply voltage: 180 W, 90 ~ 240V AC, auto range
Operating temperature: 0 ~ 40°C (32 ~ 104°F)
Weight: 4.2kg (9.3lb)
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Specications
Packing List
Safety Instructions

Keep CMOS data* Clear CMOS data
PH_6x2V_S2.00mm
RJ45 for LAN Connectors
2 FWA-3240 Startup Manual
Jumpers and Connectors
The board has a number of jumpers that allow you to con-
figure your system to suit your application. The table below
lists the function of each of the jumpers and connectors.
Connector/Jumper List
Label Function
CN2 Power Supply Connector 1x7Pin
CN9 CMOS Header 3Pin
CN1,CN2,CN12 FAN Header 4Pin
CN18 CF Header 50Pin
CN28 KB/MS Connector 1x8Pin
GF1 PCI Express Slot 64Pin
CN27 LPT Header 2x13Pin
CN23 RJ45 Connector, the default baud
rate is 19200.
CN20 External Serial Pin Header
CN24 USB Connector
CN25 (Tolapai) RJ45 for LAN Connectors
CN26 (Tolapai)
CN21 (Tolapai)
CN22 (82574L)
RJ45 for LAN Connectors
CN7 System Reset Header
CN13 Debug Port
CN29 External GPIO Header
CN17 LED Header
J1: CMOS clear function
Pins Result
1-2 Keep CMOS data*
2-3 Clear CMOS data
*: Default
CN29 : External GPIO Header
Pins Result
1
VCC
2
GND
3
9554 GPIO0
4
9554 GPIO1
5
9554 GPIO2
6
9554 GPIO3
7
9554 GPIO4
8
9554 GPIO5
9
9554 GPIO6
10
9554 GPIO7
11
GND
12
VCC
CN21,CN25,CN26,CN22 : LAN Port
LED status:
GbE Link Green (Left)
FE Link Amber (Left)
Action Link Green/Blink (Right)
Software Installation
Software tested list:
1. Linux Debian 2.6.18 kernel
2. Linux Redhat 5.0
Recommend customer to use Linux kernel 2.6.18 to develop
their own S/W.
FCC
This device complies with the requirements in Part 15 of
the FCC rules. Operation is subject to the following two
conditions.
This device may not cause harmful interference.
This device must accept any interference received,
including interference that may cause undesired opera-
tion.
1.
2.
123
123

FWA-3240 Startup Manual 3
Board Layout: Jumper and Connector Locations
Figure 1: Board Layout: Jumper and Connector Locations