Advantech USB-582 Installation and operation manual

USB-5820 Startup Manual 1
Before installation, please ensure that the following items
are included with the product:
1. 1 x USB-5820 module
2. 3 x Terminal blocks
3. 1 x USB-5820 startup manual
4. 1 x USB 3.0 lockable cable (1 m)
If any of the above items are missing or damaged, contact
your distributor or sales representative immediately.
For more detailed information regarding this product, please
download the USB-5820 user manual from the Advantech
website.
Advantech’s USB-5820 is an industrial-grade isolated ana-
log output USB 3.0 I/O module. To ensure easy installation
in cabinet computers, USB-5820 modules are compact and
equipped with a DIN-rail mount kit. The built-in USB hub can
support a daisy-chain topology, while Euro-type pluggable
terminal blocks and LED indicators can facilitate congura-
tion and maintenance.
USB-5820
4-Channel, 16-Bit, 200 kS/s Isolated Analog
Output USB 3.0 I/O Module
Startup Manual
General
• Connectors:
1 x 10-pin terminal block (3.81 mm, A/O)
2 x 3-pin screw terminal blocks (3.81 mm, power)
1 x USB 3.0 type A (downstream port)
1 x USB 3.0 type B (upstream port)
• Dimensions:
120 x 120 x 40 mm3(4.72 x 4.72 x 1.57 in3)
• OperatingTemperature: 0 ~ 60 °C (32 ~ 140 °F)
• StorageTemperature:-40 ~ 70 °C (-40 ~ 158 °F)
• StorageHumidity:5 ~ 95% RH (non-condensing)
• PowerSupply:10 ~ 30 VDC
• Interface: USB 3.0
• DataTransferRates: 5 Gbps
• PowerConsumption:
100 mA typ./130 mA max. @24 V external power
450 mA typ./770 mA max. @5 V bus power
• ESDProtection:
Air: ±8 kV
Contact: ±6 kV
• DCSurgeProtection: 2 kV
AnalogOutput
• Channels:4
• Resolution:16 bits
• OutputVoltageRange:0 ~ 5 V, 0 ~ 10 V, ±5 V, ±10 V
• OutputCurrentRange:
0 ~ 20 mA, 4 ~ 20 mA (source type)
• Load:
> 1 kΩ (voltage output) 
< 625 Ω (current output)
• OutputError:< ±0.1% of full-scale range
• IsolationProtection:2,500 VDC
• UpdatingRate:
200/n kS/s, where n is the number of enabled channels
(n = 1 ~ 4)
• SlewRate:1 V/µs
1. Install the SDK and drivers downloaded from the
Advantech website.
2. Touch the metal case of the computer to discharge any
static electricity that may be in your body.
3. Insert the USB module into the designated USB port.
Use caution when inserting the module to avoid damag-
ing the components due to excessive force.
PackingList
For more information about this or other Advantech
products, visit our website at
http://www.advantech.com
For driver/SDK downloads and technical support
services, visit our support website at
http://support.advantech.com
This manual is for USB-5820.
Part No. 2041582000
Printed in China
Edition 1
April 2019
Specications
Overview
UserManual
InstallationInstructions

2 USB-5820 Startup Manual
Power
State Description
Off Module is not powered on
Green Module is powered on using either USB
bus power or external power
Up/Error
State Description
Green Upstream port is connected. Module is
functioning normally
Red Upstream port is not connected/discon-
nected. Module function is halted
Down
State Description
Off Downstream port is not connected
Blue Downstream port is connected
Analog Output
Signal Name Description
A/O < 0 ~ 3 > Analog output channels 0 through 3
GND Ground
FCCClassA
This equipment has been tested and found to comply with
the limits for a Class A digital device, pursuant to part 15
of the FCC rules. These limits are designed to provide rea-
sonable protection against harmful interference when the
equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency
energy and, if not installed and operated in accordance with
the instruction manual, may cause harmful interference to
radio communications. Operation of this equipment in a resi-
dential area is likely to cause interference. In such cases,
users are required to correct the interference at their own
expense.
CE
This product has passed the CE test for environmental speci-
cations when shielded cables are used for external wiring.
We recommend the use of shielded cables. Such cables are
available from Advantech. Please contact your local supplier
for ordering information.
USB-5820 modules feature two power input terminals with
an input power range of 10 ~ 30 VDC and power redundancy
support. For modules connected to two power input sourc-
es, if one source is inactive or interrupted, the other power
source can immediately assume supply operations. Accord-
ingly, USB-5820 modules can operate with a single power
source. (The modules can also be powered via USB if no
device is connected to the downstream port.)
DeclarationofConformity
Power
LEDIndicators

Layout/Dimensions

PinAssignment

USB-5820 Startup Manual 3
USB-5820 modules feature a built-in DIP switch that is used to dene the board ID for each module. When multiple modules
are installed on the same system, the board ID switch can be used to identify each module’s device number. Every module in
the system should be assigned different device numbers. The default board ID value is 0. When conguring the board ID to any
other value, refer to the settings in the following table:
Switch Description
SW1
Board ID switch. Refer to the table below for board ID configuration.
Board ID 1 2 3 4
0
↑ ↑ ↑ ↑
1
↑ ↑ ↑ ↓
2
↑ ↑ ↓ ↑
3
↑ ↑ ↓ ↓
4
↑ ↓ ↑ ↑
5
↑ ↓ ↑ ↓
6
↑ ↓ ↓ ↑
7
↑ ↓ ↓ ↓
8
↓ ↑ ↑ ↑
9
↓ ↑ ↑ ↓
10
↓ ↑ ↓ ↑
11
↓ ↑ ↓ ↓
12
↓ ↓ ↑ ↑
13
↓ ↓ ↑ ↓
14
↓ ↓ ↓ ↑
15
↓ ↓ ↓ ↓
Default setting is 0
BoardIDSwitch