M-system 15BX-4 User manual

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: [phone] Fax: [phone] E-mail: [e-mail]
EM-0691-4 Rev.5 P. 1 / 3
INSTRUCTION MANUAL
STANDARD RACK
(Fujitsu FCN type I/O connector) MODEL 15BX-4
BEFORE USE ....
Thank you for choosing M-System. Before use, please check
contents of the package you received as outlined below.
If you have any problems or questions with the product,
please contact M-System’s Sales Office or representatives.
■PACKAGE INCLUDES:
Standard rack......................................................................(1)
■MODEL NO.
Confirm Model No. marking on the product to be exactly
what you ordered.
■INSTRUCTION MANUAL
This manual describes necessary points of caution when
you use this product, including installation, connection and
basic maintenance procedures.
POINTS OF CAUTION
■POWER INPUT RATING & OPERATIONAL RANGE
• Locate the power input rating marked on the product and
confirm its operational range as indicated below:
24V DC rating: 24V ±10%
■GENERAL PRECAUTIONS
• Before you remove the unit or mount it, turn off the power
supply for safety.
■ENVIRONMENT
• Indoor use.
• When heavy dust or metal particles are present in the
air, install the unit inside proper housing with sufficient
ventilation.
• Do not install the base where it is subjected to continuous
vibration. Do not subject the unit to physical impact.
• Environmental temperature must be within -5 to +55°C
(23 to 131°F) with relative humidity within 30 to 90% RH
in order to ensure adequate life span and operation.
• Be sure that the ventilation slits are not covered with ca-
bles, etc.
■WIRING
• Do not install cables close to noise sources (relay drive
cable, high frequency line, etc.).
• Do not bind these cables together with those in which
noises are present. Do not install them in the same duct.
• Be sure to put the terminal cover on while the power is
supplied.
■AND ....
• The unit is designed to function as soon as power is sup-
plied, however, a warm up for 10 minutes is required for
satisfying complete performance described in the data
sheet.
COMPONENT IDENTIFICATION
Specifications
(side)
Body
MOUNTING REQUIREMENTS unit : mm (inch)
Observe appropriate wiring space over and under the rack.
450 (17.72)
4–M5 SCREW
465 (18.31)
57.2 (2.25)
< EIA >
15 (.59)
50 (1.97)
< JIS >
ANGLE BRACKET

15BX-4
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: [phone] Fax: [phone] E-mail: [e-mail]
EM-0691-4 Rev.5 P. 2 / 3
TERMINAL CONNECTIONS
Connect the unit as in the diagram below.
■EXTERNAL DIMENSIONS unit: mm (inch)
1
168.5 (6.63)
465 (18.31)
99 (3.90)
2 (.08)
15 (.06)
480 (18.90)
435 (17.13)
2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
2
3
4
1
5
8.5 (.33)
CN1
5-M4 POWER INPUT
TERMINALS
33
(1.30)
50 (1.97)
57.2 (2.25)
■CONNECTION DIAGRAM
CN1 +
–
1
2
+
–
FG
POWER
3
4
5
■CONNECTOR PIN ASSIGNMENT
CN1: Fujitsu FCN-365P040-AU
PIN NO. CONVERTER PIN NO. CONVERTER
L O CAT. ASSIGN. LO C AT. ASSIGN.
A 1
B 1
1ch. 1
ch. 2
A11
B11
11 ch. 1
ch. 2
A 2
B 2
2ch. 1
ch. 2
A12
B12
12 ch. 1
ch. 2
A 3
B 3
3ch. 1
ch. 2
A13
B13
13 ch. 1
ch. 2
A 4
B 4
4ch. 1
ch. 2
A14
B14
14 ch. 1
ch. 2
A 5
B 5
5ch. 1
ch. 2
A15
B15
15 ch. 1
ch. 2
A 6
B 6
6ch. 1
ch. 2
A16
B16
16 ch. 1
ch. 2
A 7
B 7
7ch. 1
ch. 2
A17
B17
COM. (–)
A 8
B 8
8ch. 1
ch. 2
A18
B18
Not Used
A 9
B 9
9ch. 1
ch. 2
A19
B19
A10
B10
10 ch. 1
ch. 2
A20
B20

15BX-4
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: [phone] Fax: [phone] E-mail: [e-mail]
EM-0691-4 Rev.5 P. 3 / 3
WIRING INSTRUCTIONS
■SCREW TERMINAL
Torque: 0.8 N·m
CHECKING
1) Terminal wiring: Check that all cables are correctly con-
nected according to the connection diagram.
2) Power input voltage: Check voltage across the power ter-
minals.
3) Installation & environment
LIGHTNING SURGE PROTECTION
M-System offers a series of lightning surge protector for
protection against induced lightning surges. Please contact
M-System to choose appropriate models.