Advantech RMD-1150F-8 User manual

1
IMPORTANT SAFETY INSTRUCTIONS for LCD monitor
1. Read these instructions. Save these instructions for later use. IMPORTANT SAFETY
INSTRUCTIONS
2. Follow all warnings and instructions marked on the product.
3. Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or
aerosols cleaners. Use a damp cloth for cleaning.
4. Do not use this product near water.
5. Do not place this product on an unstable cart, stand, or table. The product may fall,
causing serious damage to the product.
6. Slots and openings in the cabinet and the back or bottom are provided for ventilation; to
ensure reliable operation of the product and to protect it from overheating, these openings
must not be blocked or covered. The openings should never be placed near or over a
radiator or heatregister, or in a built-in installation unless proper ventilation is provided.
7. This product should be operated from the type of power indicated on the marking label. If
you are not sure of the type of power available, consult your dealer or local power
company.
8. This product is equipped with a 3-wire grounding type plug, a plug having a third
(grounding) pin. This plug will only fit into a grounding-type power outlet. This is a safety
feature. If you are unable to insert the plug into the outlet,contact your electrician to
replace your obsolete outlet.Do not destroy the grounding-type plug.
9. Do not allow anything to rest on the power cord.Do not locate this product where persons
will walk on the cord.
10.If an extension cord is used with this product, make sure that the total of the ampere
ratings on the products plugged into the extension cord does not exceed the extension
cord ampere rating. Also make sure that the total of all products plugged into the wall
outlet does not exceed 15 amperes.
11.Never push objects of any kind into this product through cabinet slots as they may touch
dangerous voltage points or short out parts that could result in a risk of fire or electric
shock. Never spill liquid of any kind on the product.
12.Do not attempt to service this product by yourself, as opening or removing covers may
expose you to dangerous voltage points or other risks. Refer all servicing to service
personnel.
13.Unplug this product from the wall outlet and refer servicing to qualified service personnel
under the following conditions:
a. When the power cord or plug is damaged or frayed.
b. If liquid has been spilled into the product.

2
c. If the product has been exposed to rain or water.
d. If the product does not operate normally when the operating instructions are followed.
Adjust only those controls that are covered by the operating instructions since
improper adjustment of other controls may result in damage and will often require
extensive work by a qualified technician to restore the product to normal operation.
e. If the product has been dropped or the cabinet has been damaged.
f. If the product exhibits a distinct change in performance, indicating a need for service.

3
------------------------
Introduction
RMD1150 family specifications:
Specifications RMD-1150F-8RMD-1150KM
User port number 21
Computerportnumber 81
Cascade control PC number Upto64* N/A
On-screen display (OSD) Yes Yes
Front panel button control 8N/A
Hotplug-and-play Yes Yes
Hot-key control Yes N/A
Rack-mount kit RMK08 N/A
Automatic scan interval 3, 8, 15, 30 seconds N/A
Programmable scan pattern yes
N/A
Cable length (Max) 30M (100ft) at CONSOLE
30M (100ft) at PC ports
VGA 1600 x 1200, DDC2B
keyboard
Computer mouse connector
monitor
PS/2
PS/2, serial(with adapter)
HD-DB-15 male
keyboard
Console mouse connector
monitor
PS/2
PS/2
HD-DB-15 female
VGA Cable 4* 1M
4* 1.8M 1* 1.8M
H x W x D (mm)
(in.)
size
44x436x180
1.7x17.2x7.0
1U
N/A
Power supply (min) 9V DC, 500mA

4
Overview
Two-Console 15.0” TFT LCD display Switch
The advanced multi-access RMD-1150 Switch enable you to control multiple computers
from two different locations, remote and local with two keyboards, mice and monitors. There
is no interface card or software to configure. Installation is as easy as connecting cables
between the RMD-1150 and your computers. Operation is as simple as entering hot-key
command and navigating through the user-friendly on-screen menu. RMD-1150F-8switches
8 IBM-compatible computers and up to 64 IBM-compatible computers by cascaded. The
RMD-1150 is independent of the computer operating system.
On-Screen Display (OSD) Menu
For RMD-1150 with built-in OSD control, you can name your computers, switch to a
computer from a list, configure settings with easy-to-use menus, view the name of the
selected computer on-screen with programmable time interval. The OSD displays the
system status throughout operation.
Automatic Mouse Conversion
The RMD-1150 allow you to connect computers with PS/2 or serial mouse ports (using
adapters supplied with each RMD-1150 ) and control the computers from internal mouse pad
or one PS/2 mouse. The RMD-1150 automatically identifies the mouse and switches to
proper mouse protocol.
High Video Quality
RMD-1150 offers two console to display and control the computer that you connected.
External console supports VGA resolution up to 1600x1200 @85Hz without any degradation
and build-in console supply 15.0” LCD display by 1024x768 @75Hz. Advanced VGA circuit
design guarantees smooth and flicker-free switching from one computer to the other with
distance up to 100ft (30M)* at both Console and PC sides.
* Tested with high-quality UL2919-rated, low-loss and shielded cables.

5
Features
nSupports both PS/2 and serial mouse
nCascade configuration expands system capability
nAuto-scan automatically selects computerssequentially
nSupports Microsoft IntelliMouse (Pro)
nHot-key functions allow easy computer access
nKeyboard states automatically saved and restored when switching computers
nOperating system independent, transparent to all applications
nPlug and play system configuration
nKeyboard and mouse can be hot plugged at any time
nHigh VGA resolution 1600x1200 for external console
nDDC2B compatible
nStandard 19 inch rack mountingdesign
nSupports optional multimedia module for microphonesand stereospeakers
Extra features for On-Screen Display for KVM Switch
nAssign computers with unique and meaningful names
nIdentify and select computers by the names
nProgrammable scan filters unused computers
nStore system settings and name entries to non-volatilememory
nPassword security locks computer from unauthorized access
nGain complete control with easy-to-use OSD interface
More features for multi-access
nManage multiple computers from two locations
nDifferent Console to access, one by internal touch-pad, and external may have different
type of mouse i.e. generic PS/2 mouse and scroll mouse.
nSelectable User Timeout

6
Configurations
RMD-1150F-8 supports 8 computers. For applications with a large number of computers,
RMD-1150F-8 can be cascaded to another model’s of RMD-1150F-8’s family in a
Master/slave configuration to supportup to 64 computers.
Single RMD-1150 Configuration
In case you need to use multi-access to manage your computer systems, connect a PS/2
keyboard, a PS/2 mouse and a VGA multi-sync monitor directly to the RMD-1150F-8’s
external CONSOLE port. Then,connect multiple sets of keyboard, mouse and monitor
cables to the “PC x” ports of the RMD-1150F-8, as shown in figure1.
Figure 1: A single RMD-1150F-8 configuration
Throughout this manual, RMD-1150F-8is the Master that has a physical keyboard, mouse
and monitor connected to its CONSOLE port. Slave is a RMD-1150F-8 KVM switch family
that has its CONSOLE port connected to a RMD-1150F-8's “PC x” port. Slave only
exists in cascade configuration.

7
------------------------ Installation
External Device Connection
The monitor connected to the HD-DB-15 VGA port of aRMD-1150 CONSOLE must be
capable of synchronizing with the computer's video signal. If you are uncertain about the
monitor type, please consult the monitor user's manual. Connect a PS/2 mouse and a
keyboard to theCONSOLE port marked with a mouse and a keyboard respectively as shown
in figure 2. [NOTE: Only a PS/2 mouse can be connected to the CONSOLE mouse port.
The RMD-1150 's automatic mouse conversion system allows you to connect computers
using serial mouse and control the computers fromone PS/2 mouse.]
Figure 2: RMD-1150F-8 console connection
Determine the channel address of each computer. For computers using PS/2 mouse, connect
the computer's mouse and keyboard cables to the RMD-1150 ’s connectors marked with a
mouseand keyboardrespectively, as shown in figure 3.
Figure 3: RMD-1150F-8 computerconnection

8
For computers using serial mouse, connect the DB-9 to mini-DIN-6adapter (supplied with the
RMD-1150 ) to the computer mouse port, then use PS/2 cables to connect the mouse to
RMD-1150 , see figure 4. Connect the computer's monitor cable to the HD-DB-15 VGA
connector. Repeat above steps for all remaining computers to be connected to the
RMD-1150 .
Figure 4: Adapter and serial mouse connection

9
Initial Power-Up
Make sure all computers and RMD-1150 are powered down during installation. You
must power up the RMD-1150 before turning on any other devices.
4For single RMD-1150 :
1) Apply a power adapter to the RMD-1150 .
2) Turn on computers.
4For cascade:
1) Apply a power adapter to the RMD-1150 .
2) Apply power adapters to all Slaves.
3) Turn on computers.
Note: You may hot plug additional powered-down computerand Slave without turning existing
RMD-1150 or computer off after initial power up.
Replace RMD-1150 External Console Devices
You can replace a faulty external keyboard or mouse of the RMD-1150 CONSOLE port at
any time without powering down the RMD-1150 , as long as your computers are booted with
proper device driver for the new device.

10
------------------------
Operation
OSD (On-Screen-Display) Operation For RMD-1150 Switch
Figure 5: RMD-1150 portionOSD screen illustration
By hitting the left <CTRL> key twice within two seconds, you may see the 'Hotkey Menu' if it
is enabled (an OSD option). Or, by hitting the left <CTRL> key three times within two
seconds, you will see a 'KVM MENU' screen showing a list of the computers with
corresponding channel addresses, names and status, see figure5.
The channel address of the currently selected computer is displayed in red to the right of the
OSD title 'KVM MENU'. The color of a device name is green if it has power and is ready for
selection, or the color is white as it has no power. OSD menu updates the color when it is
activated. Use the <UP> and <DOWN> arrow keys to highlight a computer and the
<ENTER> key to select it. Or, you may press <ESCAPE> to exit OSD and remove the OSD
menu from the display; the status window returns to the display and indicates the currently
selected computer or operating status.
A triangle mark (4)to the right of a name indicates the port is cascaded to a Slave; the
number at the left of the triangle mark shows the number of ports the Slave has, i.e. 84for
KNV108. <ENTER> key brings you one level down and another screen pops up listing the
names of the computers on that Slave. The name of the Slave will be shown at the upper
right corner of the OSD menu. It is useful to group computers and still be able to see the
group name.
An eye mark(N)to the right of a name indicating the computer is selected to be monitored in

11
Scan mode. In OSD, this mark can be switched on or off by function key <F2>.
Press <ESCAPE>key to exit OSD and to return to the selected computer; the computer
name is also shown on the screen.
=Function key <F1>:To edit name entry of a computer or aSlave. First, use the <UP> and
<DOWN> arrow keys to highlight a channel then press <F1> followed by name entry.
Valid characters are ‘A’~’Z’, ‘0’~’9’and the dash character. Lowercase letters are
converted to uppercase ones. Press <BACKSPACE> to delete a letter one at a time.
Non-volatile memory stores all name entries until you change, even if the unit is powered
down.
=Function key <F2>: To switch the eye mark (N)of a computer on or off. First, use the
<UP> and <DOWN> arrow keys to highlight it, then press <F2> to switch its eye mark on or
off. If Scan Type is 'Ready PC +N', only the power-on and eye mark selected
computers will be displayed sequentially in Scan mode.
=Function key <F3>: To lock a device (a computer or a Slave)from unauthorized access,
use Security. Security is effective foronly one device (a computer or aSlave). To lock a
device, use the <UP> and <DOWN> arrow keys to highlight it, then press <F3>. Now,
enter up to 4 characters (‘A’~’Z’, ‘0’~’9, ‘-‘) followed by <ENTER> as new password. A
Security-enabled device is marked with a lock (Ï)following its channel number. To
permanently disable the security function from a locked device, highlight it, press <F3>
then enter the password.
If you want to access the locked device temporarily, simply highlight it and press <ENTER>,
the OSD will ask you for the password. After entering correct password, you are allowed to
use the device. This device is automatically re-locked once you switch to another one.
During Scan mode, OSD skips the security-enabled device. NOTE: Only one device (a
computer or aSlave) can be locked by this function at a time.
If you forget the password, the only way to permanently disable the
security function is to remove all possible power sources from the
RMD-1150 . You need to turn off all computers and unplug RMD-1150 ’s
power adapters, then restart everything.
=Function key <F4>: More functions are available by hitting <F4>. A new screen pops up
displaying more functions as described below. Most of them are marked with a triangle
(4)indicating there are options to choose from. Using the <UP> and <DOWN> arrow
keys, select the functions and press <ENTER>. Available options will be shown in the
middle of the screen. Again, using the <UP> and <DOWN> arrow keys to view options
then press <ENTER> to select it. You can press <ESCAPE> to exit at any time.
<Auto Scan
In this mode, the RMD-1150F-8automatically switches from one power-on computer
to the next sequentially in a fixed interval. During Auto Scan mode, the OSD
displays the name of the selected computer. When Auto Scan detects any
keyboard or mouse activity, it suspends the scanning till activity stops; it then
resumes with the next computer in sequence. To abort theAuto Scan mode, press
the left <CTRL> twice. Scan Type and Scan Rate set the scan pattern. Scan Type
(<F4>:More\Scan Type) determines if scanned computers must also be eye mark
selected. Scan Rate (<F4>:More\Scan Rate) sets the display interval when a
computer is selected beforeselecting the next one.

12
<Manual Scan
Scan through power-on computers one by one by keyboard control. Scan Type
(<F4>:More\Scan Type) determines if scanned computers must also be eye mark
selected. Press the up arrow key ( ↑ ) to select the previous computer and the down
arrow key ( ↓ ) to select the next computer. Press any other key to abort the
Manual Scan mode.
<Audio Stick
An optional multimedia module can be LINKed to the back of each RMD-1150 for
selecting microphone and stereo speaker signals. There are two options for Audio
Stick:ON and Off. When set to 'On', audio selection follows computer selection.
When set to 'Off', audio selection stops following computer selection. It is useful if
you want to listen to aparticular computer's audio signal while operating other
computers. The non-volatile memory stores the Audio Sticksetting.
<Scan Type
Ready PC +N: In Scan mode, scan through power-on and eye mark selected
computers.
Ready PC: In Scan mode, scan through power-oncomputers.
The non-volatile memory stores the Scan Typesetting.
<Scan Rate
Sets the duration of a computer displayed in Auto Scan mode. The options are 3
seconds, 8 seconds, 15 seconds and 30 seconds. The non-volatile memory
stores the Scan Rate setting.
<Keyboard Speed
RMD-1150 offers keyboard typematic setting that overrides the similar settings in
BIOS and in Windows. Available speed options are Low, Middle,Fast andFaster
as 10, 15, 20 and 30 characters/sec respectively.
The non-volatile memory stores the Keyboard Speed setting.
<Hotkey Menu
When you hit the left <CTRL> key twice within two seconds, the "Hotkey Menu"
appears displaying a list of hot-key commands if the option is On. The 'Hotkey
Menu' can be turned Off if you prefer not to see it when the left <CTRL> key is hit
twice.
The non-volatile memory stores the Hotkey Menu setting.
<CH Display
Auto Off: After you select a computer, the channel address and name of the
computer will appear on the screen for 3 seconds then disappear automatically.
Always On: The channel address andname of a selected computer and/or OSD
status displayed on the screen all the time.
The non-volatile memory stores the CH Display setting.
<Position
The positionof the selected computer name and/or OSD status displayed on screen
during operation. The actual display position shifts due to different VGA resolution,
the higher the resolution the higher the display position. The non-volatile memory
stores the Position setting.
UL as Upper Left, UR as Upper Right,

13
LL as Lower Left, LR as Lower Right.
MI as MIddle,
=ESC: To exit the OSD, press the <ESCAPE> key.

14
Hot-key commands
Hot-key command is a short keyboard sequence to select a computer, to activate
computer scan, etc. RMD-1150 interprets keystrokes for hot-keys all the time. A
hot-key sequence starts with two left <CTRL> keystrokes followed by one or two more
keystrokes. A built-in buzzer generates ahigh-pitch beep for correct hot-key command;
otherwise, one low-pitchbeep for error and the bad key sequence will not be forwarded to
the selected computer.
The short form hot-key menu can be turned on as an OSD function (<F4>:more\Hotkey
Menu) every time the left <CTRL> key is pressed twice.
L-CTRL: is the <CTRL> key located at the left side of the keyboard.
1~8: are the number keys '1' ~ '8' at the upper row of the keyboard. Do not use the
keypad at the right of the keyboard.
gTo select a computer by hot-key command, you must know its channel address, which
is determined by the RMD-1150F-8 connection. For a computer connected to a
RMD-1150F-8, its address is represented by the PC port label (1~8). For a computer
connected to a Slave, two characters represent its address. The first character is the
channel address of the RMD-1150F-8unit (1~8) and the second one is the channel
address of theSlave (1~8).
Left Ctrl + left Ctrl + 7
Selects a computer connected to port 7 of theRMD-1150F-8.
Left Ctrl + left Ctrl + 6 +C
Selects a computer connected to port C of a Slave connected to port 6 of the
RMD-1150F-8.
gTo start Auto Scan, automatically scan power-on computers one by one at a fixed
interval:
left Ctrl + left Ctrl + F 1
When Auto Scan detects any keyboard or mouse activity, it suspends the scanning till
activity stops; it then resumes with the next computer in sequence. The length of the
Auto Scan interval (Scan Rate) is adjustable, see below. To abort the Auto Scan mode,
press the left Ctrl key twice.
Note: Scan Type determines whether eye mark is necessary during Auto Scan.
gManual Scan enables you to manually switch back and forth between power-on
computers.
left Ctrl + left Ctrl + F2
Press ↑ or ↓ to select the previous or the next computer in sequence. And, press any
other key to abort theManual Scan.
Note: Scan Type determines whether eye mark is necessary duringManual Scan.
gTo adjust Scan Rate which sets the duration before switching to the next computer in
Auto Scan:
left Ctrl + left Ctrl + F3
The RMD-1150F-8 sends one to four beeps indicating scan interval of 3, 8, 15 and 30
seconds respectively.
gTo adjust keyboard typematic rate (characters/sec), this setting over-rides that of BIOS
and any operating system:
left Ctrl + left Ctrl + F4
The RMD-1150F-8 generates 1 to 4 beeps corresponding to 10, 15, 20 and 30
characters/sec respectively.
gAudio Stick
An optional multimedia module can be LINKed to the back of each RMD-1150F-8 for
selecting microphone and stereo speaker signals. There are two options for Audio Stick:
ON and Off. When set to 'On', audio selection follows computer selection. When set
to 'Off', audio selection stops following computer selection. It is useful if you want to

15
listen to aparticular computer's audio signal whileoperating other computers.
left Ctrl + left Ctrl + F5
The RMD-1150F-8 generates 1 or 2 beeps corresponding toOn and Off respectively.
OSD (On-Screen-Display) Operation For LCD Monitor
Control Functions
The monitor control functions are located on the bottom side of the panel. They are
shown in the figure below and described in the following paragraphs.
Key Definition
1. MENU :
Use the key to select the desired adjustment item .
2. ADJUST :
Use the key to change the value for optimalviewing
3. POWER SWITCH :
Use the power switch to turn ON or OFF power. We recommend turning your
system power on first, then the LCD monitor.
4. POWER STAND-BY MODE LED
Show LCD system in the power stand-by model.
5. Power on LED
Show LCD system in the power on model.
The control key description
1. MENU :Press any key to MENU
2. :Move to the next item
3. :Move to the previous item
4. : Increment control
5. :Decrement control
6. :Power Switch
7. SIMULTANEOUSLY: Hot key to change input channel
8. SIMULTANEOUSLY: Hot Key for Auto Adjusting

16
OSD Screen
Figure 6: LCD monitor portionOSD screen illustration
BRIGHTNESS :
Adjust the backlight bulb intensity showing onthe screen by pressing "+"or"-"
CONTRAST :
The operation is the same as the brightness by way of adjusting "+" or "-" to
change the brightness value
HORIZONTAL POSITION:
Push to move the screen to the left or right
VERTICAL POSITION :
Push to move the screen up or down
H-SCALING:
Push to increase or decrease the Horizontal screen size (not available)
AUTO ADJUSTMENT :
Press "+" or "-" to move the AUTO adjustment,find the optimal.
COLOR TEMPERATURE:
Adjust "+" or "-"to get the best color optimization
l9300K:Push to set monitor for the CIE coordinate 9300 color temperature
l6500K:Push to set monitor for the CIE coordinate 6500 color temperature
lUSER: Self defined color temperature(default)
RED GAIN:
Push to adjust"+" or "-" the screen red gain

17
GREEN GAIN:
Push to adjust"+" or "-" the screen green gain
BLUE GAIN:
Push to adjust "+" or "-" the screen blue gain
OSD HPOSITION:
Press "+" or "-" to move the OSD location to left or right hand side.
OSD VPOSITION:
Press "+" or "-" to move the OSD location to up or down.
OSD TIMER:
Press "+" or "-" to adjust the OSD Showing time.
XII GAMMAON/OFF:
Press "+" or "-"to ON/OFF
RECALL:
Push adjust "+" or "-" to RECALL the default
SPEAKER:
Audio Volume(optional)
CHANNEL SELECTION:
Press to "+" or "-" select the VGA, S-Video and Video mode
EXIT OSD EXIT:
Press "+" or "-" to execute
Table 1: LCD monitor’s OSD icon description

18
--------------- Cascade Configuration
Connection
Before connecting a device (a computer or a Slave) to the RMD-1150F-8 under power,
you must turn off the device. The RMD-1150F-8 must have equal or more 'PC x' ports
than that of the Slave.
The ports labeled "PC 1"~”PC 8”can be connected to either a computer or a Slave's
CONSOLE port, as shown in figure 7. A power adapter with DC 12V/3.5A output rating
must be connected to theRMD-1150F-8,it supply either LCD display and switch to work.
The maximum number of computers controlled by a Master/slave configuration with
RMD-1150F-8, the number is 64 with 8 Slaves and each Slave connects to 8 computers,
see also figure 7.
Figure 7: Cascaded 8-port RMD-1150F-8s
For system check by OSD :
After connection completes, you should re-activate the KVM portion OSD menu to check if the
RMD-1150F-8recognizes the Slaves. Atriangle mark (4)is placed to the right of the channel name
indicating the port is connected to a Slave not a computer. A number to the left of the triangle mark
indicates theSlave model, i.e. 84for KNV108 or KNV108D.
Change Configuration while Running
Devices at any 'PC x' port can be changed at any time after initial power-up. If you
change any one of the “PC 1” to “PC 8” portsconnection from a computer to a Slave or
vice versa, or replace the devices of a port; the OSD will update this change the next time
it is activated. [NOTE: Any new device, a computer or aSlave, must be turned off before
it is connected tothe RMD-1150 .]

19
Operation
On power up, the RMD-1150 is in Idle mode broadcasting VGA signal from the selected
computer and detecting for keyboard and mouse activity.
No matter internal or external keyboard or mouse activity is detected, the RMD-1150
immediately disables the other CONSOLE from accessing the computer. In the mean time,
keyboard LEDs (Num/Caps/Scroll Lock) of the other CONSOLE start to flash as its
access is denied and the monitor is blocked from VGA signal for security reason. After
the user has finished his operation for a period of time (i.e., User Timeout), the
multi-access RMD-1150 Switch returns to Idle mode. User Timeout has four options, 5
sec, 30 sec, 60 sec and HOLD. Select HOLD when you plan to access the RMD-1150
for a long time. Pressing the <Scroll Lock> twice forces the RMD-1150 return to Idle
mode immediately regardless of theUser Timeoutsetting.
The User Timeoutis available in the OSD menu by pressing the Function key <F4>, under
the sub-menu More. Note: Keyboard Speed option is not available for multi-access
models.

20
------------------------ Appendices
Specifications of 15" TFT LCD Monitor
Item Specification
Dimensions (mm) 300.0mm(L) x 285.0mm(W) x 47.0mm(D)
Weight (g) 2756±5(g)
Display Area 304.1(H) X 228.1(V) (15.0-inch diagonal)
Number of Pixels 1024(H) X 768(V)
Pixel Pitch (mm) 0.297(H) X 0.297(V)
Number of Colors 16.7M(color)
Backlight Unit 2 replaceable CCFLs edge-light (top/bottom)
Brightness (cd/m²) 200(cd/m²)(Typ.)
Viewing Angle -60º~60º(H), -55º~45º(V)(Typ.)
Environmental
consideration Operating temperature:0ºC~ 50ºC(32 F~ 122 F) humidity 10-85% maximum
Storage temperature:-20ºC~ 60ºC(-4 F~ 140 F)
humidity 10-90% maximum
Power source AC 90-264V Universal
I/O Connectors DC power in, VGA 15-pin D-sub, AV-connector,
S-video connector
Safety /Regulations FCC, CE, UL
The LCD Products listed on this document are not suitable for use of aerospace
equipment, submarine cables, nuclear reactor control system and life support
systems. If customers intend to use these LCD products for above application or not
listed in "Standard" as follows, please contact our sales people in advance.
Standard: Computer, Office equipment, Communication equipment, Test and
Measurement equipment, Machine tool, Industrial robot, Audio and Visual equipment,
Other consumer products.
Cleaning the Monitor
1. Make sure the monitor is turned off.
2. Never spray or pour any liquid directly onto the screen or case.
3. Wipe the screen with a clean, soft, lint-free cloth. This removes dust and other
particles.
4. The display area is highly prone to scratching. Do not use ketene type material
(ex. Acetone), Ethyl alcohol, toluene, ethyl acid or Methyl chloride to clear the
panel. It might permanently damage the panel.
5. If still not clean, apply a small amount of non-ammonia, non-alcohol based glass
cleaner onto a clean, soft, lint-free cloth, and wipe the screen
6. Don't let water or oil penetrate the monitor. If the droplets are kept for a long time,
Staining and discoloration may occur.