AEG Favorit 87000 User manual

Favorit 87000
User manual Dishwasher

Thank you for choosing one of our high-quality products.
To ensure optimal and regular performance of your appliance please read this
instruction manual carefully. It will enable you to navigate all processes perfectly
and most efficiently. To refer to this manual any time you need to, we recommend
you to keep it in a safe place. And please pass it to any future owner of the appliance.
We wish you much joy with your new appliance.
Contents
Operating instructions 3
Safety information 3
Children and vulnerable persons safety
3
General safety 3
Use 3
Care and cleaning 4
Installation 4
Frost precautions 4
Water connection 4
Electrical connection 5
Service centre 5
Disposal of the appliance 5
Product description 6
Control panel 7
Cancel button 8
Programme selection buttons 8
Extra silent programme button 8
Multitab button 8
Delay start button 8
Display 8
Function buttons 8
Setting mode 9
Use of the appliance 9
Setting the water softener 9
Manual adjustment 10
Electronic adjustment 10
Use of dishwasher salt 11
Use of detergent and rinse aid 11
Use of detergent 11
Use of rinse aid 12
Adjust the rinse aid dosage 12
Multitab function 12
Loading cutlery and dishes 13
Hints and tips 13
Washing programmes 13
Select and start a washing programme 14
Select and start a washing programme
without delay start 14
Select and start a washing programme with
delay start 15
Interruption of a washing programme
15
How to cancel a washing programme or a
delay start 15
At the end of the washing programme
15
Auto Off 16
Remove the load 16
Care and cleaning 16
To remove and clean the filters 16
To clean the spray arms 17
To clean the external surfaces 17
What to do if… 17
The washing results and drying results are
not satisfactory 19
How to activate the rinse aid dispenser
20
Technical data 20
Environment concerns 20
Installation instructions 21
Installation 21
Installation under a counter 21
How to remove the appliance worktop
21
To adjust the level of the appliance 22
Water drain connection 22
Subject to change without notice
2Contents

Operating instructions
Safety information
Before the installation and use, read this manual carefully:
• For your personal safety and the safety of your property.
• For the respect of the environment,
• For the correct operation of the appliance.
Always keep these instructions with the appliance also if you move or sell it.
The manufacturer is not responsible if an incorrect installation and use causes damage.
Children and vulnerable persons safety
• Do not let persons, children included, with reduced physical sensory, reduced mental
functions or lack of experience and knowledge use the appliance. They must have su-
pervision or instruction for the operation of the appliance by a person who is responsible
for their safety.
• Keep all packaging away from children. There is the risk of suffocation or physical injury.
• Keep all detergents in a safe area. Do not let the children touch the detergents.
• Keep children and small animals away from the appliance when the door is open.
General safety
• Do not change the specifications of this appliance. There is the risk of injury and damage
to the appliance.
• Obey the safety instructions from the manufacturer of the dishwasher detergent to
prevent burns to eyes, mouth and throat.
• Do not drink the water from the appliance. Detergent residue can stay in your appliance.
• Always close the door after you load or unload the appliance to prevent injury and to
prevent someone falling on an open door.
• Do not sit or stand on the open door.
Use
• The appliance is only for domestic use. Do not use the appliance for commercial and
industrial use or for other uses.
• Do not use the appliance for uses other than that for which it made. You will prevent
physical injury to persons or prevent damage to property.
• Only use the appliance to clean household utensils that are applicable for dishwashers.
• Do not put flammable products or items that are wet with flammable products in, near
or on the appliance. Risk of explosion or fire.
• Put the knives and all items with sharp points in the cutlery basket with their points
down. If not, put in a horizontal position in the upper basket or in the knife basket. (Not
all models have the knife basket).
• Use only specified products for dishwashers (detergent, salt, rinse aid).
• Types of salt that are not specified for dishwashers can cause damage to the water
softener.
• Fill the appliance with salt before you start a washing programme. The grains of salt and
salty water can cause corrosion or make a hole in the bottom of the appliance.
Safety information 3

• Do not fill the rinse aid dispenser with products other than rinse aid, (e.g. dishwasher
cleaning agent, liquid detergent). This can cause damage to the appliance.
• Make sure that the spray arms can move freely before you start a washing programme.
• If you open the door while the appliance is in operation, hot steam can escape. There is
a risk of skin burns.
• Do not remove the dishes from the appliance before the end of the washing programme.
Care and cleaning
• Before maintenance, switch off the appliance and disconnect the mains plug from the
mains socket.
• Do not use flammable products or products that can cause corrosion.
• Do not use the appliance without the filters. Make sure that the installation of the filters
is correct. An incorrect installation causes unsatisfactory washing results and damage
to the appliance.
• Do not use spray water or steam to clean the appliance. Risk of electrocution and damage
to the appliance.
Installation
• Make sure that the appliance has not suffered any damage while in transport. Do not
connect a damaged appliance. If necessary, contact the supplier.
• Remove all packaging before first use.
• Only a qualified person must do the electrical and the plumbing installation, the set up
and the maintenance of the appliance. This to prevent the risks of structural damage or
physical injury.
• Make sure that the mains plug is disconnected from the mains socket during installation.
• Do not drill into the sides of the appliance to prevent damage to hydraulic components
and electrical components.
Frost precautions
• Do not install the appliance where the temperature is below 0°C.
• The manufacturer is not responsible for frost damage.
Water connection
• Use new hoses to connect the appliance to the water supply. Do not use used hoses.
• Do not connect the appliance to new pipes or pipes not used for a long time. Let the
water flow for some minutes, then connect the inlet hose.
• Make sure not to squash or cause damage to the water hoses when you install the
appliance.
• Make sure that the water couplings are tight to prevent a water leakage.
• The first time you use the appliance, make sure that the hoses do not have water leaks.
• The water inlet hose is double-walled and has an inner mains cable and a safety valve.
The water inlet hose is under pressure only when the water flows. If there is a leak in the
water inlet hose, the safety valve interrupts the running water.
– Be careful when you connect the water inlet hose:
– Do not put the water inlet hose or the safety valve in water.
– If the water inlet hose or the safety valve are damaged, immediately disconnect
the mains plug from the mains socket.
4Safety information

– Contact the service centre to replace the water inlet hose with safety valve.
WARNING!
Dangerous voltage.
Electrical connection
• The appliance must be earthed.
• Make sure that the electrical data on the rating plate agree with your domestic power
supply.
• Always use a correctly installed shockproof socket.
• Do not use multi-way plugs, connectors and extension cables. There is a risk of fire.
• Do not replace or change the mains cable. Contact the service centre.
• Make sure not to squash or cause damage to the mains plug and cable behind the
appliance.
• Make sure that the mains plug is accessible after the installation.
• Do not pull the mains cable to disconnect the appliance. Always pull the mains plug.
Service centre
• Only an approved engineer can repair or work on the appliance. Contact the service
centre.
• Use only original spare parts.
Disposal of the appliance
• To prevent the risk of physical injury or damage:
– Disconnect the mains plug from the mains socket.
– Cut off the mains cable and discard it.
– Discard the door catch. This prevents children or small animals from being closed
inside of the appliance. There is a risk of suffocation.
Safety information 5

WARNING!
The dishwasher detergents are dangerous and can cause corrosion !
• If an accident occurs with these detergents, contact immediately your regional poisons
centre and a doctor.
• If the detergent gets into the mouth, contact immediately your regional poisons centre
and a doctor.
• If the detergent gets into the eyes, contact immediately a doctor and wet the eyes with
water.
• Keep dishwasher detergents in a safe area and out of children touch.
• Do not keep the appliance door open when there is detergent in the detergent dispenser.
• Fill the detergent dispenser only before you start a washing programme.
Product description
2
3
4
5
6
7
1
8
9
10
11
1Upper basket
2Water hardness dial
3Salt container
4Detergent dispenser
5Rinse aid dispenser
6Rating plate
7Filters
8Lower spray arm
9Upper spray arm
10 Top spray arm
11 Worktop
6Product description

Control panel
123456
7
8
9
10
ABC
1On/off button
2Cancel button
3Programme selection buttons
4Extra silent programme button
5Multitab button
6Delay start button
7Display
8Function buttons
9Indicator lights
10 Programme indicator lights
Indicator lights
Salt
1)
It comes on when it is necessary to fill the salt container. Refer to 'Use of dish-
washer salt'.
After you fill the container, the salt indicator light can stay on for some hours.
This does not have an unwanted effect on the operation of the appliance.
Control panel 7

Indicator lights
Rinse aid
1)
It comes on when it is necessary to fill the rinse aid container. Refer to 'Use of
detergent and rinse aid'.
MULTITAB It comes on when you activate the multitab function. Refer to 'Multitab func-
tion'.
1) When the salt and/or rinse aid containers are empty, the related indicator lights do not come on while a washing
programme operates.
Cancel button
With this button you can cancel a washing programme or a delay start. Refer to 'Select and
start a washing programme'.
Programme selection buttons
With these buttons you can select the washing programme. Press one of the buttons again
and again until the indicator light of the necessary programme comes on.
Refer to 'Washing programmes' for more data about the washing programmes.
Extra silent programme button
This is a washing programme that operates with a low level of noise.
During the Extra Silent the pump works at a very low speed. This to decrease the level of
noise of 25% compared to the declaration programme. Because of this the programme has
a very long time duration.
Set this washing programme in times when the power rate is more economical.
Multitab button
Press this button to activate/deactivate the multitab function. Refer to 'Multitab function'.
Delay start button
Use this button to delay the start of the washing programme with an interval between 1
and 24 hours. Refer to 'Select and start a washing programme'.
Display
The display shows:
• The electronic adjustment of the level of the water softener.
• Activation/deactivation of the rinse aid dispenser (only with multitab function on).
• The washing programme duration.
• Remaining time to the end of the washing programme.
• The end of a washing programme. The display shows a zero.
• Remaining time to the end of the delay start.
•Faultcodes.
Function buttons
Use the function buttons for these operations:
• To adjust electronically the level of the water softener. Refer to 'Setting the water soft-
ener'.
• To deactivate/activate the rinse aid dispenser when the multitab function is on. Refer to
'What to do if...'.
8Control panel

Setting mode
The appliance must be in setting mode for these operations:
• To select and start a washing programme and/or a delay start.
• To adjust electronically the level of the water softener.
• To deactivate/activate the rinse aid dispenser.
Press the on/off button. The appliance is in setting mode when:
– All the programme indicator lights come on.
Press the on/off button. The appliance is not in setting mode when:
– Only one programme indicator light comes on.
– The display shows the duration of a washing programme or a delay start.
– It is necessary to cancel the programme or the delay start to go back to the setting
mode. Refer to 'Select and start a washing programme'.
Use of the appliance
Refer to the instructions for each step of procedure:
1. Make a check if the adjustment of the water softener agrees with the water hardness
in your area. If necessary, adjust the water softener.
2. Fill the salt container with dishwasher salt.
3. Fill the rinse aid dispenser with rinse aid.
4. Load cutlery and dishes into the appliance.
5. Set the correct washing programme for the type of load and soil.
6. Fill the detergent dispenser with the correct quantity of detergent.
7. Start the washing programme.
If you use the combi detergent tablets ('3 in 1', '4 in 1', '5 in 1'), refer to 'Multitab function'.
Setting the water softener
The water softener removes minerals and salts from the water supply. Minerals and salts
can have a bad effect on the operation of the appliance.
Equivalent scales measure the water hardness:
• German degrees (dH°).
• French degrees (°TH).
• mmol/l (millimol for each litre - international unit for the hardness of water).
• Clarke degrees.
Adjust the water softener to the water hardness in your area. If necessary, contact your
local water authority.
Water hardness Water hardness adjustment
°dH °TH mmol/l Clarke manually electronically
51 - 70 91 - 125 9,1 - 12,5 64 - 88 2
1)
10
43 - 50 76 - 90 7,6 - 9,0 53 - 63 2
1)
9
Use of the appliance 9

Water hardness Water hardness adjustment
°dH °TH mmol/l Clarke manually electronically
37 - 42 65 - 75 6,5 - 7,5 46 - 52 2
1)
8
29 - 36 51 - 64 5,1 - 6,4 36 - 45 2
1)
7
23 - 28 40 - 50 4,0 - 5,0 28 - 35 2
1)
6
19 - 22 33 - 39 3,3 - 3,9 23 - 27 2
1)
5
1)
15 - 18 26 - 32 2,6 - 3,2 18 - 22 1 4
11 - 14 19 - 25 1,9 - 2,5 13 - 17 1 3
4 - 10 7 - 18 0,7 - 1,8 5 - 12 1 2
< 4 < 7 < 0,7 < 5 1
2)
1
2)
1) Factory position.
2) No use of salt is necessary.
You must adjust the water softener manually and electronically.
Manual adjustment
Turn the water hardness dial to the position 1 or 2
(refer to the chart).
Electronic adjustment
1. Switch on the appliance.
2. Make sure that the appliance is in setting mode.
3. Press and hold function buttons B and C until the programme indicator lights above
function buttons A, B and C start to flash.
4. Release function buttons B and C.
5. Press function button A.
– The programme indicator lights above function buttons B and C go off.
– The programme indicator light above function button A continues to flash.
– The display shows the current adjustment.
Example: the display shows = level 5.
6. Press the function button A again and again until the display shows the necessary
adjustment.
7. Press the on/off button to keep the operation.
If the water softener is set electronically to the level 1, the salt indicator light stays off.
10 Setting the water softener

Use of dishwasher salt
Do these steps to fill the salt container:
1. Turn the cap counterclockwise to open
the salt container.
2. Fill the salt container with 1 litre of water
(only with the first operation).
3. Use the funnel to fill the salt container
with salt.
4. Remove the salt around the opening of
the salt container.
5. Turn the cap clockwise to close the salt
container.
It is correct that water comes out from the salt
container when you fill it with salt.
Use of detergent and rinse aid
20
30
M
A
X
1
2
3
4
+
-
1234
5
6
7
Use of detergent
To help the environment, do not use more than the correct quantity of detergent.
Follow the detergent manufacturer recommendations on the detergent packaging.
Do these steps to fill the detergent dispenser:
1. Press the release button
2
to open the lid
7
of the detergent dispenser.
2. Put the detergent in the dispenser
1
.
3. If the washing programme has a prewash phase, put a small quantity of detergent on
the inner part of the appliance door.
4. If you use the detergent tablets, put the tablet in the detergent dispenser
1
.
5. Close the detergent dispenser. Press the lid until it locks into position.
Use of dishwasher salt 11

Different brands of detergent dissolve in different times. Some detergent tablets do not
have the best cleaning results during short washing programmes. Use long washing pro-
grammes when you use the detergent tablets to fully remove the detergent.
Use of rinse aid
Rinse aid makes it possible to dry the dishes without streaks and stains.
The rinse aid dispenser automatically adds rinse aid during the last rinsing phase.
Do these steps to fill the rinse aid dispenser:
1. Press the release button
6
to open the lid
5
of the rinse aid dispenser.
2. Fill the rinse aid dispenser
3
with rinse aid. The mark 'max' shows the maximum level.
3. Remove the spilled rinse aid with an absorbent cloth to prevent too much foam during
the washing programme.
4. Close the rinse aid dispenser. Press the lid until it locks into position.
Adjust the rinse aid dosage
Factory set: position 3.
You can set the rinse aid dosage between position 1 (lowest dosage) and position 4 (highest
dosage).
Turn the rinse aid selector
4
to increase or decrease the dosage.
Multitab function
The multitab function is for combi detergent tablets.
These tablets contain agents as detergent, rinse aid and dishwasher salt. Some types of
tablets can contain other agents.
Do a check if these tablets are applicable for the local water hardness. Refer to the in-
structions from the manufacturer.
When you set the multitab function, it stays on until you deactivate it.
The multitab function deactivates the flow of rinse aid and salt.
The multitab function deactivates the indicator lights of salt and rinse aid.
The programme duration can increase if you use the multitab function.
Activate the multitab function before the start of a washing programme.
You cannot activate the multitab function when the programme operates.
To activate the multitab function:
• Press the multitab button. The multitab indicator light comes on.
To deactivate the multitab function and use separately detergent, salt and rinse aid:
1. Press the multitab button. The multitab indicator light goes off.
2. Fill the salt container and rinse aid dispenser.
3. Adjust the water hardness setting to the highest level.
4. Do a washing programme without dishes.
5. Adjust the water softener to the water hardness in your area.
6. Adjust the rinse aid dosage.
12 Multitab function

Loading cutlery and dishes
Refer to the leaflet 'Examples of ProClean loads'.
Hints and tips
Do not use the appliance to clean objects that can absorb water (e.g. sponges, household
cloths).
• Before you load cutlery and dishes, follow these steps:
– Remove remaining food.
– Make remaining burnt food in the pans soft.
• While you load cutlery and dishes, follow these steps:
– Load hollow items (e.g. cups, glasses and pans) with the opening down.
– Make sure that water does not collect in the container or in a deep base.
– Make sure that cutlery and dishes do not bond together.
– Make sure that the glasses do not touch other glasses.
– Put small objects in the cutlery basket.
– Mix the spoons with other cutlery to prevent them from bonding together.
– Arrange the items to let water touch all surfaces.
• Plastic items and pans with non-stick coatings can retain the water droplets.
• Put light items in the upper basket. Make sure that the items do not move.
Washing programmes
Programme Degree of soil Type of load Programme description
AUTO 45°-70°
1)
Any Crockery, cutlery,
pots and pans
Prewash
Main wash 45 °C or 70 °C
1 or 2 middle rinses
Last rinse
Dry
INTENSIV PRO 70° Heavy soil Crockery, cutlery,
pots and pans
Prewash
Main wash 70 °C
1 middle rinse
Last rinse
Dry
30 MIN 60°
2)
Normal or light
soil
Crockery and cutlery Main wash 60 °C
Rinse
ECO 50°
3)
Normal soil Crockery and cutlery Prewash
Main wash 50 °C
1 middle rinse
Last rinse
Dry
Loading cutlery and dishes 13

Programme Degree of soil Type of load Programme description
Normal or light
soil
Delicate crockery and
glassware
Main wash 45 °C
1 middle rinse
Last rinse
Dry
This programme gives dishes a quick rinse
to prevent the remaining food to bond on
the dishes and bad odours to come out
from the appliance.
Do not use detergent with this pro-
gramme.
1 cold rinse
EXTRA SILENT Normal soil Crockery and cutlery Prewash
Main wash 50 °C
1 middle rinse
Last rinse
Dry
1) The appliance adjusts automatically the temperature and the quantity of the water. This depends if the appliance
has a full load or not and on the degree of soil. The programme duration and the programme consumptions
can change.
2) When you have a light load, this programme gives a timesaving solution with perfect washing results.
3) Test programme for test institutes. Refer to supplied leaflet for test data.
Consumption values
Programme
1)
Energy (kWh) Water (litre)
AUTO 45°-70° 0,9 - 1,7 8 - 15
INTENSIV PRO 70° 1,5 - 1,7 13 - 15
30 MIN 60° 0,9 9
ECO 50° 0,9 - 1,1 9 - 11
0,8 - 0,9 11 - 12
0,1 4
EXTRA SILENT 1,1 - 1,2 9 - 11
1) The display shows the programme duration.
The pressure and temperature of the water, the variations of power supply and the quantity
of dishes can change these values.
Select and start a washing programme
Select and start a washing programme without delay start
1. Open the door.
2. Switch on the appliance.
3. Make sure that the appliance is in setting mode.
4. Select a washing programme. Refer to 'Washing programmes'.
– The related programme indicator light comes on.
14 Select and start a washing programme

– All other programme indicator lights go off.
– The programme duration flashes in the display.
5. Close the appliance door. The washing programme starts automatically.
You can select the washing programme also with the door closed. When you press a pro-
gramme button, you have only 3 seconds to select a different washing programme. After
these 3 seconds, the washing programme start automatically.
Select and start a washing programme with delay start
1. Open the door.
2. Switch on the appliance and select a washing programme.
3. Press the delay start button again and again until the display shows the necessary
number of hours for the delay start.
4. Close the appliance door.
– The countdown starts automatically.
– When the countdown is completed, the washing programme starts automatically.
The opening of the appliance door interrupts the countdown. When you close the door,
the countdown continues from the point of interruption.
You can select the delay start also with the door closed. When you select a washing pro-
gramme, you have only 3 seconds to select the delay start. After these 3 seconds, the
washing programme starts automatically.
Interruption of a washing programme
• Open the appliance door.
– The washing programme stops.
• Close the appliance door.
– The washing programme continues from the point of interruption.
How to cancel a washing programme or a delay start
If a washing programme or a delay start has not started, you can change the selection.
When a washing programme or a delay start are in progress, it is not possible to change
the selection. It is necessary to cancel the washing programme or the delay start to make
a new selection.
When you cancel the delay start, this automatically cancels the selected washing pro-
gramme. You have to select the washing programme again.
1. Press and hold the cancel button until all the programme indicator lights come on.
2. Make sure that there is detergent in the detergent dispenser before you start a new
washing programme.
At the end of the washing programme
• The appliance stops automatically.
• The display shows 0.
1. Switch off the appliance.
2. Open the appliance door.
Select and start a washing programme 15

3. For better drying results, keep the door ajar for some minutes.
• If you do not switch off the appliance, after three minutes from the end of the washing
programme:
– all indicator lights go off,
– the display shows one horizontal bar,
This helps to decrease energy consumption.
Press one of the buttons (not the on/off button), the display and the indicator lights come
on again.
Auto Off
The Auto Off function automatically switches off the appliance 10 minutes after the end
of the washing programme.
This helps to decrease energy consumption.
Remove the load
• Let the dishes become cold before you remove them from the appliance. Hot dishes are
easily damaged.
• First remove the items from the lower basket, then from the upper basket.
• There can be water on the sides and door of the appliance. Stainless steel becomes cool
more quickly than the dishes.
Care and cleaning
To remove and clean the filters
Dirty filters decrease the washing results. Although the maintenance is very low with these
filters, we recommend that you make a check at intervals and if necessary, clean them.
1. To remove filter (A), turn it counterclock-
wise and remove it out from filter (B).
A
B
16 Care and cleaning

2. Filter (A) has 2 parts. To disassemble the
filter, pull them apart.
3. Fully clean the parts under running water.
4. Put the 2 parts of the filter (A) together
and push. Make sure that they assemble
correctly in each other.
5. Remove the filter (B).
6. Fully clean the filter (B) under running wa-
ter.
7. Put the filter (B) to its initial position. Make
sure that it assembles correctly under the
two guides (C).
8. Put the filter (A) into position in filter (B)
and turn it clockwise until it locks.
To clean the spray arms
Do not remove the spray arms.
If the holes in the spray arms become clogged, remove remaining parts of soil with a cocktail
stick.
To clean the external surfaces
Clean the external surfaces of the appliance and control panel with a damp soft cloth. Only
use neutral detergents. Do not use abrasive products, scouring pads or solvents (e.g. ace-
tone).
What to do if…
The appliance does not start or stops during operation.
First try to find a solution to the problem (refer to the chart). If not, contact the service
centre.
Malfunction Fault code Possible cause Possible solution
The appliance does not
fill with water.
• An audible signal
operates.
• The display shows
.
The water tap is
blocked or is furred
with limescale.
Clean the water tap.
C
What to do if… 17

Malfunction Fault code Possible cause Possible solution
The water pressure is
too low.
Contact your local wa-
ter authority.
The water tap is closed. Open the water tap.
The filter in the water
inlet hose is blocked.
Clean the filter.
The connection of the
water inlet hose is not
correct.
Make sure that the
connection is correct.
The water inlet hose is
damaged.
Make sure that the wa-
ter inlet hose has no
damages.
The appliance does not
drain the water.
• An audible signal
operates.
• The display shows
.
There is a blockage in
the sink spigot.
Clean the sink spigot.
The connection of the
water drain hose is not
correct.
Make sure that the
connection is correct.
The water drain hose is
damaged.
Make sure that the wa-
ter drain hose has no
damages.
The anti-flood device
operates.
• An audible signal
operates.
• The display shows
.
Close the water tap
and contact the serv-
ice centre.
The programme does
not start.
The appliance door is
open.
Close the door correct-
ly.
The mains plug is not
connected in.
Put in the mains plug.
Blow out fuse in the
household fuse box.
Replace the fuse.
The delay start is set. If you want to cancel
the delay start, refer to
'Select and start a
washing programme'.
After the check, switch on the appliance. The programme continues from the point of
interruption.
If the malfunction shows again, contact the service centre.
If the display shows other fault codes, contact the service centre.
The necessary data for the service centre is on the rating plate.
We recommend that you write the data here:
Model (MOD.) ....................
18 What to do if…

Product number (PNC) ....................
Serial number (S.N.) ....................
The washing results and drying results are not satisfactory
Problem Possible cause Possible solution
The dishes are not clean. The selected washing pro-
gramme was not applicable for
the type of load and soil.
Make sure that the washing
programme is applicable for the
type of load and soil.
The baskets were not loaded
correctly, water did not touch
all surfaces.
Load the baskets correctly.
The spray arms could not turn
freely because of incorrect ar-
rangement of the load.
Make sure that an incorrect ar-
rangement of the load does not
cause a blockage of the spray
arms.
The filters are dirty or not as-
sembled and installed correct-
ly.
Make sure that the filters are
clean and correctly assembled
and installed.
The quantity of detergent was
not sufficient or missing.
Make sure that the quantity of
detergent is sufficient.
Limescale particles on the
dishes.
The salt container is empty. Fill the salt container with dish-
washer salt.
Incorrect water softener ad-
justment
Adjust the water softener.
The salt container cap is not
closed correctly.
Make sure that the salt con-
tainer cap is closed correctly.
There are streaks, milky stains,
or a bluish layer on glasses and
dishes.
Rinse aid dosage is too high. Decrease the rinse aid dosage.
Dry water drop stains on
glasses and dishes.
Rinse aid dosage is too low. Increase the rinse aid dosage.
The detergent can be the cause. Use a different brand of deter-
gent.
The dishes are wet. You have set a washing pro-
gramme without drying phase
or with a decreased drying
phase.
Let the door stay ajar for some
minutes before you remove the
dishes.
The dishes are wet and dull. The rinse aid dispenser is emp-
ty.
Fill the rinse aid dispenser with
rinse aid.
The multitab function is on.
(The rinse aid dispenser is au-
tomatically off).
Activate the rinse aid dispenser.
Refer to 'How to activate the
rinse aid dispenser'.
What to do if… 19

How to activate the rinse aid dispenser
1. Switch on the appliance.
2. Make sure that the appliance is in setting mode.
3. Press and hold function buttons B and C.
– The programme indicator lights above function buttons A, B, and C start to flash.
4. Release function buttons B and C.
5. Press function button B.
– The programme indicator lights above function buttons A and C go off.
– The programme indicator light above function button B continues to flash.
– The display shows the current set.
Rinse aid dispenser deactivated
Rinse aid dispenser activated
6. Press function button B again.
– The display shows the new adjustment.
7. Switch off the appliance to keep the operation.
Technical data
Dimensions Width 596 mm
Height 850 mm
Depth 625 mm
Water supply pressure Minimum 0,5 bar (0,05 MPa)
Maximum 8 bar (0,8 MPa)
Water supply
1)
Cold water or hot water maximum 60 °C
Capacity Place settings 12
1) Connect the water inlet hose to a water tap with a 3/4'' thread.
The rating plate on the inner edge of the appliance door shows the electrical connection
data.
If the hot water comes from alternative sources of energy, (e.g. solar panels, photovoltaic
panels and aeolian), use a hot water supply to decrease energy consumption.
Environment concerns
The symbol on the product or on its packaging indicates that this product may not be
treated as household waste. Instead it should be taken to the appropriate collection point
for the recycling of electrical and electronic equipment. By ensuring this product is disposed
of correctly, you will help prevent potential negative consequences for the environment
and human health, which could otherwise be caused by inappropriate waste handling of
this product. For more detailed information about recycling of this product, please contact
20 Technical data