aeolus AEOLIAN TD-901GT User manual

Distributor Contacts
TD-901GT
PET DRYER
Producer : Shanghai TOEX International Trading Co., Ltd.
Address : Floor 5, Building 6, No.675 Zhujin Road,
Songjiang District, Shanghai, 201615, China
Manufacturer : Shanghai Xunyuan Industrial Co., Ltd.
Address : Building 8, No. 65 Huandong First Road,
Jinshan District, Shanghai, China
New Legend
xtraordinary Blow Force
utstanding Durability and Sturdiness
ong Lasting Carbon Brush &Motor
nbeatable Single Motor Dryer
uperb Noise Control Technique
AEOLIAN
TD-901T
TD-907T
TD-900XT TD-900CG
TD-905 TD-906 TD-907L
Owner’s Guide
TD-901GT
PET DRYER

()
Structure Chart
Remarks: The chart is only for repair parts order references, the real structure should be subject to current available product,
since we may make modifications without notice in formal written form.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
23
24
25
26
28
30
31
32
33
34
35
36
37
1
3
3
3
1
3
1
1
5
1
4
2
4
4
4
1
1
1
2
1
1
6
1
1
1
1
1
1
1
1
3
1
2
1
1
1
TD-90001
TD-90002
TD-90003
TD-90004
TD-90005
TD-90006
TD-90007
TD-90008
TD-90009
TD-90010
TD-90011
TD-90012
TD-90013
TD-90014
TD-90015
TD-90051
TD-90052
TD-90018
TD-90019
TD-90020
TD-90021
TD-90023
TD-90024
TD-90025
TD-90026
TD-90028
TD-90053
TD-90054
TD-90030
TD-90031
TD-90032
TD-90033
TD-90034
TD-90035
TD-90036
TD-90055
Part Name Quantity
Rear Cap Fixture Knob
M4×10 Screw
Washer
Rear Cap Rubber Foot
Rear Cap
M4 Lock Nut
Foam Filter
Handle
M4×12 Screw and Nut
Short Housing
Housing Rubber Foot
Handle Set
PA3×8 Self-tapping Screw
Washer
M5×10 Screw
Vibration Absorber Ring (for Motor-B)
Motor (B-220V/110V)
Rubber Washer
Carbon Brush
Single Motor Fixture Bracket
Rubber Seal
Heating Element Assembly (220V/110V)
(Not installed in 100V model.)
Heating Switch
(Not installed in 100V model.)
PA3×16 Self-tapping Screw
Front Cap -A
Power Cable
Wind Speed Knob
PCB-C (220V/110V)
PCB-D (100V)
Power Switch
Front Cap D52 Hose Connector
D52 Nylon Clip
D52 Flexible Hose
D52 Hose Connector
D52 Narrow Nozzle
D52 Round Nozzle
D52
Heat Insulation Sleeve
PG-9 Waterproof Cable Connector
Serial No.
Item No.
For your safety, this screw must be
fixed after flexible hose plugged into
the connector on front cap.
22 TD-90022
27 TD-90027
29
1
1

Maintenance
The wind speed and blow force is dramatically different in single motor and dual motor dryers.
As powerful as our TD-901T Cyclone single motor dryer is, it can’t compare to our Dual Motor Hercules
TD-900XT. Hercules double motor dryer measures 955g of blow force; 605g for Cyclone.
Our aim was to create a single motor dryer that bridged the gap. We worked on this for a few years, and
in 2012 the problem was solved. We created an incredibly powerful single motor dryer which can even
match Hercules in both wind speed and blow force.
Thus the aptly named AEOLIAN was created.
Super Blow Force
895g① of super blow force, is what AEOLIAN produces. No other single motor dryer comes close Most
dual motor dryers in the market perform at the average level of 780 -850g blow force, which to say
Monster has already beaten them and just slightly less forceful than our own double motor dryer, Hercules
(TD-900XT).
90m/s②is a new level of performance in this field.
Better Mobility
It is a AEOLIAN of performance in a compact, lightweight body. 6kg (even more), this 4.7kg portable
single dryer is the ideal choice for all. There are two options for flexibility of use; a stand and wall mount.
They both provide hands free usage and leave the work space free for grooming.
Motor Life Span
The enlarged surface area of the 32mm carbon brush helps to extend the lifespan by 20%. The bigger
motor (with stronger torque and slower rotation speed) generates much more wind volume than average
motors do; (and helps to extend its own life by rotating less).
Maintenance
IIf you compare AEOLIAN with a dual motor dryer, you will find you are saving labor cost, time and money
on the maintenance of AEOLIAN. One pair of carbon brushes need to be changed after about 800 service
hours (rather than 2 pairs as on a dual motor dryer). Much Simpler internal structure and less wiring
translate to less time devoted to maintenance.
Noise Control
As strong and powerful as the AEOLIAN is, it remains remarkably quiet.
It’s only 79dbA when noise dosimeter is positioned above Monster.
Safety Performance
The USA produced temperature switch, cuts the heating element of the TD-901GT in 25ms, and begins
working again after the core temperature of the heating element reduces to 85 degrees Celsius, which
allows the TD-901GT to perform at an output temperature of a maximum of 52 degrees Celsius③.
TD-901GT has high temperature resistant silicone wiring, switch and circuit boards. The emergency cut
off switch responds readily if perchance a motor were to overheat.
Ease of Use
AEOLUS TD-901GT has a proprietary easy use nozzle attachment which allows the operator to remove
the nozzle head with the use of just one finger, with a simple click of the attachment.
Aeolus TD-901GT nozzle allows reattachment of nozzle head with just one click.
Accessories
AEOLUS TD-901GT options include:
Wall mounting bracket
Groomers’ third arm
Dryer Stand
Please check instruction manual for further details
Testing Condition:
All testing results are under condition of 220V-50Hz, using 2800W model.
1)2.5m long flexible hose, Φ16mm round nozzle, fixed above the high precision electronic scale at 220mm, record the blow force indication.
2)2.5m long flexible hose, Φ16mm round nozzle, fixed at the distance of 180mm to the center of wind cup, record the wind speed indication.
3)52℃means the sensor fixed at the position of 3cm away from the end of round nozzle never takes a value higher than 52℃in a 3 hours
continuous testing, when the environmental temperature is at 32℃.
Remarks: all the testing is executed on professional testing platforms.
1. Plug the flexible hose to the front cap connector.
2. Plug in socket with right voltage, switch power on.
3. Adjust wind speed, turn on or off the heating switch and choose suitable nozzle according to your need.
4. Turn the wind speed knob back to Minimum, turn off the heating switch and then turn off the power switch
after usage.
5. Unplug the dryer from the mains, unplug the hose and nozzle, and put the machine and accessories back to
box.
1. Please clean the sponge filter by washing or air blowing, be sure to fix the filter again when it’s dry.
2. Keep the surface clean and dry, and use a dry and soft cloth to clean the painted surface.
3. Wet cloth with neutral detergent and wipe to remove stubborn stains and dirt.
4. Use only mild neutral detergent.
5. When the carbon brushes run out, please renew the brushes following the guide line in this booklet or
consult with the professionals.
Direction for Use
C1
C2
R1
R2
DB3
TH
MOT1
VR1
VR2 SW1
SW2
SWT
TRIAC
L
N G
Safety Instruction
1. Pet dryer needs a single outlet which is at least 10A and has ground wire for itself. Please connect pet dryer
with a correct outlet and do not share with other appliances.
2. Before switch on or turn off the power every time, please adjust the wind and temperature to the lowest, this
can extend the lifetime of the machine.
3. Do not insert pins or any metal things into the clearance of the machine, otherwise that would be easy to get
an electric shock and short circuit.
4. Do not use a cloth or bag to stop the diffuser or foam filter; otherwise it would damage the machine.
5. If the machine has been used for some time and a malfunction occurs, you must ask the professional
person to repair it. Do not disassemble by yourself.
6. If the power cord is damaged, discontinue use and have repaired by a professional.
7. Please keep children away when you operate the machine.
8. Do not hit the housing with fierce shock or drop the machine from high, which will damage the frame and motor.
9. Cardiopath or people with pacemaker are forbidden to use this machine.
10. Please hold the nozzle and hose firmly before turning the machine on, or the hose may wiggle and cause injury.
11. Must plug hose into the front cap connector before turning the machine on.
12. It’s strictly forbidden to touch the components in the front cap connector with hand or any other objects in
any situation.
13. Apliance is not intended for use by persons (including children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction
concerning use of the appliance by a person responsible for their safety.
14. Children should be supervised to ensure that they do not play with the appliance.
15. If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly
qualified person in order to avoid a hazard.
Remarks:
①. We cannot find any anemoscope to measure the real wind speed of this TD-901GT dryer, between
the another single motor dryer CYCLONE in our line and TD-901GT.
1.The parameters are tested with 2.5m long flexible hose and Φ16mm round nozzle.
2.We may not publish formal notice in written form when the parameters changed after new improvements.
3.The manufacturing standards and testing stands subject to TOEX company standard: TXPS-ALPD-0901(T)-2012.
Parameters Circuit Diagram
A dryer we have nothing else to entitle but AEOLIAN
Correct Disposal of this product
This marking indicates that this product should not be disposed with other household wastes
throughout the EU. To prevent possible harm to the environment or human health from uncon-
trolled waste disposal, recycle it responsibly to promote the sustainable reuse of material
resources. To return your used device, please use the return and collection systems or contact
the retailer where the product was purchased. They can take this product for environmental
safe recycling.
Not equipped in
100V model
AEOLIAN
340×160×210mm
450×300×230mm
(Flexible Hose not Included)
(Environmental Temperature at 32℃)
Product Name
Rated Voltage
Rated Current
Maximum Power
Heating Power
Maximum Temperature
Net Weight
Product Dimension
Blow Force
Maximum Wind Speed
①
Minimum Wind Speed
Noise
Gross Weight
Packing Dimension
(on top of the dryer at 0.5m)
(L×W×H)
Noise
(on back of the dryer at 1m)
110V -120V/ 60Hz220V -240V/ 50Hz
12.7A
895g 726g 726g
19.1A
2800W
90m/s
79dbA 78dbA
86dbA 85dbA
27m/s
73m/s 73m/s
2100W
100V/ 60Hz
15A
1500W
Class
0
600W 600W
52℃
4.1kg
4.9kg
78dbA
85dbA
4.1kg
4.9kg5.5kg
4.75kg
TD-901GT

1. 2.
5. 6.
3. 4.
Put all the parts back in reverse order.
Carbon Brush
Remove the retaining screws on
front cap by cross screwdriver in
arrow direction, and open the front
cap.
Wall-mounting Bracket
Fix the retaining screws in broken line
showed in the picture; examine the strength
and stability after works done.
The wall which you want to attach the bracket
to must be a solid wall which could bear
weight loading!
Remove these three screws which
fixing the motor bracket one by
one.
Put the new brushes in, and tighten the
brass clip with nipper pliers.
Press the clip down on the connectors of
the wires to motor, unplug the wires and
remove the front cap.
Lift the little iron panel up with flathead
screwdriver, open the brass clip which
holding the motor wire to remove the old
carbon brushes.
Twist the little iron to a certain angle to
fix the carbon brush brass rear cap.
Groomers Third Arm
1. 2.
Dryer Stand
1. 2.
Fix the nozzle with the metal clamp.
Slide the latch to fix the
dryer in showed direction.
Slide the dryer into position
of the bracket in arrow
direction.
※ The power supply must be cut off before changing carbon brushes.