Aerovent IM-110 Manual

©1997-2016 Aerovent
Typical Panel Fan Installations
MOUNTING BLOCKS
OR PLATES
STD. MOUNT
WWII
GUARD STD. FLG.
SHUTTER
AIRFLOW
ANGLE IRON
FRAME
ALLOW SPACE FOR
DAMPER MOTOR
BIRD
SCREEN
WEATHER HOOD
FAN & SHUTTER
FLUSH-MOUNTED
MOUNTED IN WALL
SHUTTER FLUSH ON OUTSIDE
ANGLE
IRON
FRAME
AIRFLOW
AIRFLOW
FLAT
GUARD
PMS
GUARD
REV. FLG.
SHUTTER
WEATHER HOOD
BIRD
SCREEN
OR
OR
OR
REVERSE FLOW
PANEL
STANDARD FLOW
PANELS
REVERSE MOUNT
PANEL
WWII
GUARD
INSIDE MOUNT OUTSIDE MOUNT
SHUTTER
MTR. OPERATED
CTR. PIVOT ONLY
BIRD
SCREEN
WEATHER HOOD
PMS GUARD
REVERSIBLE PANELS
EXHAUST INSTALLATIONS
INSTALLATION REQUIRES SHUTTER SIZE TO BE SAME AS PANEL SQUARE.
General Installation, Operation and Maintenance Instructions For Aerovent Products
IM-110
June 1997
Panel and Ring Fans
Throughout this manual, there are a number of HAZARD WARNINGS that must be read and adhered to in
order to prevent possible personal injury and/or damage to equipment. The signal word "CAUTION" is used to
indicate the severity of a hazard and is preceded by the safety alert symbol.
CAUTION
Used when minor or moderate injury or product / equipment damage MAY result from misuse or failure to
follow specific instructions.
It is the responsibility of all personnel involved in installation, operation and maintenance to fully understand
the Caution procedures by which hazards are to be avoided.

2 Aerovent Installation and Maintenance Manual IM-110
INSTALLATIONS USING MOUNTING ADAPTORS
AIRFLOW AIRFLOW
AUTOMATIC
SHUTTER
AUTOMATIC
SHUTTER
STANDARD MOUNT ALTERNATE MOUNT
(REVERSIBLE)
AIRFLOW
(REVERSE FLOW)
AIRFLOW AIRFLOW
AIRFLOW
AIRFLOW
AIRFLOW
AIRFLOW
CENTER-PIVOT
MOTOR-OPERATED
SHUTTERS
RECOMMENDED MOUNT RECOMMENDED MOUNT
(REVERSE CONSTRUCTION)
NOTE: ALL INSTALLATIONS SHOWN
USE SAME SIZE SHUTTERS &
HOODS AS FAN SIZE.
CENTER-PIVOTED
MOTOR-OPERATED
SHUTTER
CENTER-PIVOTED
MOTOR-OPERATED
SHUTTER
FLAT
GUARD
AUTOMATIC
SHUTTER
OUTSIDEOUTSIDE
SUPPLY
ARRANGEMENT
EXHAUST
ARRANGEMENT
AUTOMATIC
SHUTTER
EXHAUST W/MTG. ADAPTOR
SUPPLY W/WALL HOUSING
STANDARD CONSTRUCTION
ALTERNATE SOLUTIONS

Aerovent Installation and Maintenance Manual IM-110 3
Typical Ring Fan Installations
STANDARD FLOW
AIR-
FLOW
ALTERNATE
WMF GUARD
REPLACES
SPLIT WIRE
GUARD
MOUNTS
TO WALL
STD. FLOW RING FAN
W/MTG. PLATE, ROUND
PROP SIDE GUARD &
SPLIT WIRE GUARD
WALL
STD.
SHUTTER
AIR-
FLOW
WALL
ALTERNATE
WMF GUARD
REPLACES
SPLIT WIRE
GUARD
MOUNTS
TO WALL
STD. FLOW RING FAN
W/MTG. PLATE, ROUND
PROP SIDE GUARD &
SPLIT WIRE GUARD
STD.
SHUTTER
WEATHERHOOD
W/BIRD SCREEN
REVERSE CONSTRUCTION
REVERSE FLOW OR REVERSIBLE
AIR-
FLOW
ALTERNATE
WMF GUARD
REPLACES
SPLIT WIRE
GUARD
MOUNTS
TO WALL
REV. CONSTRUCTION
RING FAN W/MTG.
PLATE, ROUND
GUARD & SPLIT
WIRE GUARD
REVERSE
FLANGE
MOUNTING
ADAPTORWALL
REV. FLANGE
CENTER-PIVOTED
MOTOR-OPERATED
SHUTTER
AIR-
FLOW
ALTERNATE
WMF GUARD
REPLACES
SPLIT WIRE
GUARD
MOUNTS
TO WALL
REVERSE FLOW
OR REVERSIBLE
RING FAN W/MTG.
PLATE, ROUND
GUARD & SPLIT
WIRE GUARD
WALL
CENTER-
PIVOT
MOTOR-
OPERATED
SHUTTER
WEATHERHOOD
W/ BIRD SCREEN
AIRFLOW
FAN MOUNTED
FLUSH TO WALL
FAN MOUNTED
TO DUCTWORK

Rear Wire Guard (WWII)(Motorside)
For Panel Fans
PARTS
(1) Rear Panel
(4) Side Panels
(16) or (24) Hex Head Locknuts
(16) or (24) 5∕16" x 1" Hex Head Capscrews
(32) or (48) 3∕8" I.D. Flat Washers
ASSEMBLY
1. Bolt three sides of guard to rear panel using
5∕16" capscrews, nuts and flat washers.
2. Bolt partially assembled guard to panel fan
using capscrews, nuts and flat washers.
3. Arrange for electrical hook-up to fan motor. Two
methods may be used:
a. Drill out hole in fan panel and route wire or
conduit through opening.
Round Motorside Basket Guard
– OR –
b. Bend or cut side panel wire guard and route
wire or conduit through opening.
4. Assemble fourth side to guard and panel, sliding
along conduit or wiring if routing through guard.
5. Securely tighten all locknuts.
Cleaning Propellers
The propeller in an axial flow fan must be kept
reasonably clean if it is to perform properly. Fans
handling fresh air for ventilating purposes will
seldom need cleaning. Fans exhausting process air
should be cleaned as required. Dirt or chemical
deposits will usually build up on a propeller evenly
and they present no problem to performance or
operation until they become thick enough to break
away in crust-like pieces. When this happens, the
propeller may be thrown out of balance and the
resulting vibration could be serious. Accumulations
of deposits should be removed by solvent cleaning
or scraping. If the propeller has been coated, be
careful not to cut through the protective covering.
Care and Maintenance
Regular and systematic inspection of all fan
parts is a necessity for good fan maintenance.
A general installation and maintenance
brochure (IM-100) has been supplied with this
shipment. It includes fan and motor bearing
lubrication, care and replacement of V-belt
drives and taperlock bushing instructions.
2MWG04/16
Attach
Guard
To Wall
4 Mounting
Holes
Ring Fan
Basket Guard
WWW.AEROVENT.COM
5959 Trenton Lane N | Minneapolis, MN 55442 | Phone: [phone] | Fax: [phone]
®
Recommended distance between fan blade and shutter is approximately equal to 1⁄3
of the fan’s diameter.
CAUTION