Aewin Technologies AW-A795 User manual
Control Board
Model Number：AW-A795
Intel®Pentium®4 Embedded SBC with Six Gigabit/Two 10/100LAN &
SSD
User’s Manual
Version 1.0
Weembedyourneed!
© Copyright 2005
User’s Manual
©2002 AEWIN Technologies Co., Ltd.. All rights reserved. Ver 1.0. Jan. 2005
2
© Copyright 2005. All Rights Reserved
Manual Edition 1.0, January 2005
This document contains proprietary information protected by copyright. All rights are
reserved, no part of this manual may be reproduced, copied, translated or transmitted in
any form or by any means without prior written permission of the manufacturer.
The content of this manual is intended to be accurate and reliable, the original
manufacturer assumes no responsibility for any inaccuracies that may be contained in this
manual. The original manufacturer reserves the right to make improvements to the
products described in this manual at any time without prior notice.
Trademarks
IBM, EGA, VGA, XT/AT, OS/2 and PS/2 are registered trademarks of International business
Machine Corporation
Award is a trademark of Award Software International, Inc
Intel is a trademark of Intel
RTL is a trademark of Realtek
VIA is a trademark of VIA Technologies, Inc
Microsoft, Windows, Windows NT and MS-DOS are either trademarks or registered
trademarks of Microsoft Corporation
All other product names mentioned herein are used for identification purpose only and may
be trademarks and/or registered trademarks of their respective companies
Limitation of Liability
While reasonable efforts have been made to ensure the accuracy of this manual, the
manufacturer and distributor assume no liability resulting from errors or omissions in this
manual, or from the use of the information contained herein.
User’s Manual
©2002 AEWIN Technologies Co., Ltd.. All rights reserved. Ver 1.0. Jan. 2005
3
Table of Contents
Chapter 1. General Information-------------------------------------------------------------5T
1.1 Introduction---------------------------------------------------------------------------------5
1.2 Specification---------------------------------------------------------------------------------6
1.3 AW-A795 Package--------------------------------------------------------------------------7
1.4 Board Layout--------------------------------------------------------------------------------8
1.5 Board Dimension----------------------------------------------------------------------------8
Chapter 2. Connectors Location and Configuration-------------------------------------9
2.1 Connectors/Jumpers Location and Define---------------------------------------------9
2.2 Installing Processors-----------------------------------------------------------------------11
2.3 Installing Memory-------------------------------------------------------------------------14
2.4 Connector and Jumpers Settings-------------------------------------------------------17
CN1:USB0 Connnector-----------------------------------------------------------------------17
CN2/3:LAN (10/100) Connector-----------------------------------------------------------------------17
CN4/5/6/7/8/9:Gigabit LAN Connector---------------------------------------------------17
CN10:COM1 RJ45 Connector --------------------------------------------------------------------17
CN11/20/24/28/29/30/31:FAN Connector-------------------------------------------------------------18
CN12:Power LED Pin Header----------------------------------------------------------------------18
CN13:USB1 Pin Header -------------------------------------------------------------1 8
CN14:COM2 Box Header--------------------------------- ------------------------------------------------18
CN15:Parallel Box Header------------------------------------------------------------------18
CN16:ATX Power Connector---------------------------------------------------------------18
CN17:Mini PCI-------------------------------- ----------------------------------------------------------------19
CN18:GPIO Pin Header -----------------------------------------------------------------------------------20
CN19/21:SATA0/1 Connector ------------------------------------------------------------------------20
CN22:SATA LED Pin Header-----------------------------------------------------------------20
CN23:HDD Power Connector--------------------------------------------------------------------20
CN25:IDE (2mm) 44-pin 90 degree---------------------------------------------------------------------20
CN26:IDE (2.54mm) 40-pin Connector-------------------------------------------------------------21
CN27:+12V Power Connector-------------------------------------------------------------------21
CN32:HDD LED Pin Header-----------------------------------------------------------------21
CN33:PS/On Pin Header----------------------------------------------------------------21
CN34:Reset Pin Header---------------------------------------------------------------------21
User’s Manual
©2002 AEWIN Technologies Co., Ltd.. All rights reserved. Ver 1.0. Jan. 2005
4
CN36:KB/MS Pin Header------------------------------------------------------------------------22
CN37:LAN LED Pin Header---------------------------------------------------------------------22
CN38:LAN LED Pin Header-------------------------------------------------------------------------22
JP1:PS/On Always On Select--------------------------------------------------------------------------22
JP2/4/5:PCI-X slot Frequency Select------------------------------------------------------------------23
JP3:Speak Buzzer Enable---------------------------------------------------------------23
JP6: Clear CMOS-----------------------------------------------------------------------------------------23
Chapter 3. BIOS Setup-------------------------------------------------------------------------24
3.1 Quick Setup----------------------------------------------------------------------------------24
3.2 Entering the CMOS Setup Program----------------------------------------------------25
3.3 Menu Options--------------------------------------------------------------------------------26
Standard CMOS Features---------------------------------------------------------------------27
Advanced BIOS Features----------------------------------------------------------------------28
Advanced Chipset Features-------------------------------------------------------------------30
Integrated Peripherals--------------------------------------------------------------------------31
Power Management Setup---------------------------------------------------------------------32
PNP/PCI Configuration------------------------------------------------------------------------34
PC Health Status---------------------------------------------------------------------------------36
Load Fail-Safe Default--------------------------------------------------------------------------36
Load Optimized Default------------------------------------------------------------------------37
Set Supervisor & User Password-------------------------------------------------------------38
Chapter 4. Drivers and Utilities Installation-----------------------------------------------40
4.1 Ethernet Driver Installation --------------------------------------------------------------40
4.2 System Chipset Driver Installation------------------------------------------------------47
Appendix A. System Resources----------------------------------------------------------------50
Appendix B. Optional Cable List--------------------------------------------------------------53
User’s Manual
©2002 AEWIN Technologies Co., Ltd.. All rights reserved. Ver 1.0. Jan. 2005
5
Chapter 1. General Information
1.1Introduction
THE AW-A795 embedded computing board, an “all-in-one” Network Security Hardware
Appliance based on Intel® architecture with E7501+ICH3+P64H2 chipset supporting the
Pentium® 4 processor with 400/533MHz FSB. The DDR 200/266 RAM (PC2100 registered)
with ECC for enhanced data integrity up to 4GB. Based on E7501 chipset, AW-795 support
eight Ethernet ports including six GbE ports, two 10/100BASE-T coppers for various
markets and performance requirements.
Other features includes a CompactFlash socket, one PCI-X 133MHz slot and one Mini PCI
socket for flexible expansion capabilities, one IDE connector, two USB ports, two Serial
ports, one Parallel port, digital I/O, watchdog timer and hardware system monitoring for 1U
chassis applications to give the customer a complete platform solution.
User’s Manual
©2002 AEWIN Technologies Co., Ltd.. All rights reserved. Ver 1.0. Jan. 2005
6
1.2Specification
General Functions
CPU Intel Pentium® 4 based processors with 400/533MHz Front-side Bus
BIOS Award® 512KB Flash BIOS
Chipset Intel® E7501 + ICH3 + P64H2
I/O Chipset Winbond® 83627HF
Memory Onboard two 184-pin DDR DIMM socket, support PC2100 registered
memory up to 4Gbytes
Enhanced IDE Support up to two IDE devices
Serial port Two RS-232 ports, oneRJ-45 connector and one pin header
Parallel port One pin header for parallel port
KB/Mouse
connector 5x2 header onboard support PC/AT Keyboard and PS/2 mouse
USB connectors Two USB ports, one with pin header
PCI Slot One 64-bit PCI-X 133MHx
Watchdog Timer Can generate a system reset, Support software selectable timeout
interval.
System
Monitoring Support temperatures, fan speed and voltages monitoring
Digital I/O Support eight application definable LEDs
Ethernet Interface
Chipset Two Intel® 82551ER Fast Ethernet controller. Triple Intel®82546GB
Fast Ethernet controller for Copper.
Ethernet interface PCI 10/100Mbps Ethernet controller, IEEE 802.3U protocol
compatible
SSD Interface One 50-pin CompactFlash™ socket
Mechanical and Environmental
Power supply voltage Standard ATX Power supply
Operating temperature 32 to 140℉(0 to 40℃)
Board size 11.7”(L) x 13.1”(W) , (300mmx350mm)
User’s Manual
©2002 AEWIN Technologies Co., Ltd.. All rights reserved. Ver 1.0. Jan. 2005
7
1.3AW-A795 Package
Please make sure that the following items have been included in the package
before installation.
1. AW-A795 Low Power Embedded SBC
2. Quick Setup
3. Cable: Please refer to Appendix B Optional Cables
4. CD-ROM which contains the following folders:
(1) Manual
(2) System Driver
(3) Ethernet Driver
(4) Tools
If any of these items are missing or damaged, please contact your dealer from
whom you purchased the board at once. Save the shipping materials and
carton in the event that you want to ship or store the board in the future. After
you unpack the board, inspect it to assure an intact shipment. Do not apply
power to the board if it appears to have been damaged.
Leave the board in its original packing until you are ready to install
Precautions
Please make sure you properly ground yourself before handling the AW-A795 board or
other system components. Electrostatic discharge can be easily damage the AW-A795
board.
Do not remove the anti-static packing until you are ready to install the AW-A795 board.
Ground yourself before removing any system component from it protective anti-static
packaging. To ground yourself, grasp the expansion slot covers or other unpainted parts of
the computer chassis.
Handle the AW-A795 board by its edges and avoid touching its component.
User’s Manual
©2002 AEWIN Technologies Co., Ltd.. All rights reserved. Ver 1.0. Jan. 2005
8
1.4 Board Layout
1.5 Board Dimension
User’s Manual
©2002 AEWIN Technologies Co., Ltd.. All rights reserved. Ver 1.0. Jan. 2005
9
Chapter 2. Connectors/Switch Location and Configuration
2.1 Connectors/Jumpers Location and Define
User’s Manual
©2002 AEWIN Technologies Co., Ltd.. All rights reserved. Ver 1.0. Jan. 2005
10
Connector Define
CN1 USB0 Connector CN2 LAN (10/100) Connector
CN3 LAN (10/100) Connector
User’s Manual
©2002 AEWIN Technologies Co., Ltd.. All rights reserved. Ver 1.0. Jan. 2005
11
CN4 Gigabit LAN Connector
CN5 Gigabit LAN Connector
CN6 Gigabit LAN Connector
CN7 Gigabit LAN Connector
CN8 Gigabit LAN Connector
CN9 Gigabit LAN Connector
CN10 COM1 RJ45 Connector
CN11 FAN Connector
CN12 Power LED Pin Header
CN13 USB1 Pin Header
CN14 COM2 Box Header
CN15 Parallel Box Header
CN16 ATX Power Connector
CN17 Mini PCI
CN18 GPIO Pin Header
CN19 SATA0 Connector
CN20 FAN Connector
CN21 SATA1 Connector
CN22 SATA LED Pin Header
CN23 HDD Power Connector
CN24 FAN Connector
CN25 IDE(2mm) 44 Pin 90 Degree
CN26 IDE(2.54mm) 40 Pin
CN27 +12V Power Connector
CN28 FAN Connector
CN29 FAN Connector
CN30 FAN Connector
CN31 FAN Connector
CN32 HDD LED Pin Header
CN33 PS-On Pin Header
CN34 Reset Pin Header
CN36 KB/MS Pin Header
CN37 LAN LED Pin Header
CN38 LAN LED Pin Header
Buzzer 1 Speak Buzzer
JP1 PS-On/Always On Select
JP2,4,5 PCI-X Slot Frequency Select
JP3 Speak Buzzer Enable
JP6 Clear CMOS
2.2. Installing Processors
The AW-A795 onboard built-in socket 479 for Intel® Pentium® 4 Processors. After installing
the processor, you should proceed to installing the heatsink or cooler.
User’s Manual
©2002 AEWIN Technologies Co., Ltd.. All rights reserved. Ver 1.0. Jan. 2005
11
2.2.1 Installing CPU:
User’s Manual
©2002 AEWIN Technologies Co., Ltd.. All rights reserved. Ver 1.0. Jan. 2005
12
2.2.2 Remove CPU
(1) First, please push the tappet to unlock location.
(2) Then untie the screw beginning from left side you can refer to below the picture.
(3) Now you can take out the CPU from socket.
User’s Manual
©2002 AEWIN Technologies Co., Ltd.. All rights reserved. Ver 1.0. Jan. 2005
13
2.2.3 How to recognize CPU
Before you install CPU please make sure the CPU is exactly Pentium 4 processor.
You can see the difference from CPU code and the pin out at backside.
(1) Pentium M CPU (Socket 479)
(2) PIII CPU – (uFCPGA Package)
User’s Manual
©2002 AEWIN Technologies Co., Ltd.. All rights reserved. Ver 1.0. Jan. 2005
14
(3) Pentium 4 CPU (Socket 478)
2.3 Installing Memory
To insert a DIMM Memory:
The AW-A795 supports two 184-pin DDR sockets, memory up to 4GB. Please make sure to
insert DDR with registered.
User’s Manual
©2002 AEWIN Technologies Co., Ltd.. All rights reserved. Ver 1.0. Jan. 2005
15
To Insert a DIMM Memory: Please align the module with the socket key and press down
until the levers at each end of the socket snap close up.
There is only one direction for installing a module in the socket. Do not attempt to force the
module into the socket incorrectly.
User’s Manual
©2002 AEWIN Technologies Co., Ltd.. All rights reserved. Ver 1.0. Jan. 2005
16
To Remove a DIMM Memory: To remove a DIMM, press down on the levers at both end of
the module until the module pops out
There is only one direction for installing a module in the socket. Do not attempt to force
the module into the socket incorrectly.
User’s Manual
©2002 AEWIN Technologies Co., Ltd.. All rights reserved. Ver 1.0. Jan. 2005
17
2.4 Connector and Jumper Settings
CN1 : USB0 Connector
Pin Define
1 +5V
2 Data0-
3 Data1+
4 Ground
CN2/3 LAN (10/100) Connector
Pin Define
1 TX0+
2 TX0-
3 RX0+
4 N/C
5 N/C
6 RX0-
7 N/C
8 N/C
LED:
D1 :Speed LED
10 Mbps DIM
100 Mbps Green
D2 :Link/Activity LED
Link Yellow
Activity Blinking
CN4/5/6/7/8/9:Gigabit LAN connector
Pin Define
1 TX0+
2 TX0-
3 RX0+
4 N/C
5 N/C
6 RX0-
7 N/C
8 N/C
LED:
D1 :Bi-Color Speed
LED
10 Mbps Off
100 Mbps Yellow
1000Mbps Green
D2 :Link/Activity LED
Link Green
Activity Blinking
CN10:COM1 RJ45 Connector
Pin Define
1 CTS#
2 DTR#
3 TXD#
4 NC
User’s Manual
©2002 AEWIN Technologies Co., Ltd.. All rights reserved. Ver 1.0. Jan. 2005
18
5 NC
6 RXD#
7 PSR#
8 RTS#
CN11/20/24/28/29/30/31:FAN Connector
CN12:Power LED Pin Header
Pin Define
1 VCC
2 GND
CN13:USB1 Pin Header
Pin Define
1 USBVCC
2 USBP1N
3 USBP1P
4 Ground
5 Ground
CN14 :COM2 Box Header
Pin Define Pin Define
1 DCD# 6 DSR#
2 RXD# 7 RTS#
3 TXD# 8 CTS#
4 DTR# 9 RI#2
5 Ground 10 NC
CN15 :Parallel Box Header
Pin Define Pin Define
1 STROBE 14 AUTOFD
2 PD0 15 ERR
3 PD1 16 INT
4 PD2 17 SLCTIN
5 PD3 18 Ground
6 PD4 19 Ground
7 PD5 20 Ground
8 PD6 21 Ground
9 PD7 22 Ground
10 ACK* 23 Ground
11 BUSY 24 Ground
12 PE 25 Ground
13 SLCT 26 Ground
CN16:ATX Power Connector
Pin Define Pin Define
11 +3.3V 1 +3.3V
12 -12V 2 +3.3V
13 Ground 3 Ground
14 PS_ON* 4 +5V
15 Ground 5 Ground
16 Ground 6 +5V
17 Ground 7 Ground
User’s Manual
©2002 AEWIN Technologies Co., Ltd.. All rights reserved. Ver 1.0. Jan. 2005
19
18 -5V 8 POWER GOOD
19 +5V 9 5VSB
20 +5V 10 +12V
CN17:Mini PCI
Pin Define Pin Define
1 TIP 2 RING
3 8PMJ-33 4 8PMJ-13
5 8PMJ-63 6 8PMJ-23
7 8PMJ-73 8 8PMJ-43
9 8PMJ-83 10 8PMJ-53
11 LED1_GRNP 12 LED2_YELP
13 LED1_GRNN 14 LED2_YELN
15 CHSGND 16 RESERVED
17 INTB/D# 18 5V
19 3.3V 20 INTA/C#
21 RESERVED 22 RESERVED
23 GND 24 3.3VAUX
25 CLK 26 RST#
27 GND 28 3.3V
29 REQ# 30 GNT#
31 3.3V 32 GND
33 AD{31} 34 PME#
35 AD{29} 36 RESERVED
37 GND 38 AD{30}
39 AD{27} 40 3.3V
41 AD{25} 42 AD{28}
43 RESERVED 44 AD{26}
45 C/BE[3]# 46 AD{24}
47 AD{23} 48 IDSEL
49 GND 50 GND
51 AD{21} 52 AD{22}
53 AD{19} 54 AS{20}
55 GND 56 PAR
57 AD{17} 58 AD{18}
59 C/BE[2]# 60 AD[16]
61 IRDY# 62 GND
63 3.3V 64 FRAME#
65 CLKRUN# 66 TRDY#
67 SERP# 68 STOP#
69 GND 70 3.3V
71 PERP 72 DEVSEL#
73 CB/E[1] 74 GND
75 AD[14] 76 AD[15]
77 GND 78 AD[13]
79 AD[12] 80 AD[11]
81 AD[10] 82 GND
83 GND 84 AD[09]
85 AD[06] 86 C/BE[0]#
87 AD[07] 88 3.3V
89 3.3V 90 AD[06]
91 AD[05] 92 AD[04]
93 RESERVED 94 AD[02]
95 AD[03] 96 AD[00]
97 5V 98 RESERVED_
WIP4
99 AD[01] 100 RESERVED_
WIP4
101 GND 102 GND
103 AC_SYNC 104 M66EN
105 AC_SDATA_I
N 106 AC_SDATA_
OUT
107 AC_BIT_CLK 108 AC_CODEC_
ID0#
109 AC_CODEC_
ID1# 110 AC_RESET#
111 MOD_AUDIO
_MOD 112 RESERVED
113 AUDIO_GND 114 GND
115 SYS_AUDIO_
OUT 116 SYS_AUDIO_
IN
Table of contents
Other Aewin Technologies Computer Hardware manuals
