AgfaPhoto DC-302 User manual

1
CONTENT
1. Advisory Note
1.1 CD-ROM
1.2 Before using the DC-302
1.3 Copyright information
1.4 Caution when using the camera
2. Getting to know your DC-302
2.1 Control Reference
2.2 Monitor screen display
3. Usage preparations
3.1 Load batteries and memory card
3.2 Turn ON/OFF the camera
3.3 Set up

2
3.4 Playback function
3.5 Using your DC-302
4. How to install and use the application
4.1 Driver Installation
4.2 Software Installation
5. Specifications
6. Q&A section
7. Addendum
8. Customer care

3
1. Advisory Note
Thank you for purchasing this AGFAPHOTO DC-302 digital camera.
Please read these operating instructions carefully in order to use the
product correctly. Keep the instructions in a safe place after reading so that
you can refer to them later.
1.1 CD-ROM
The software CD-ROM packaged with the camera is designed for PC only.
To play this CD-ROM on a stereo or CD player may cause damage to it.
This camera is a precision electronic device. Do not attempt to service this
camera yourself, as opening or removing covers may expose you to
dangerous voltage points or other risks. This will invalidate all guarantee
claims. Do not expose this camera under direct sunlight to avoid causing a
fire.
1.2 Before using the DC-302
Try to take some pictures before you perform the formal recording. Before
taking pictures with this camera of any important occasion (such as a

4
wedding ceremony or on vacation), do test the camera beforehand to
ensure that it functions well. Any additional loss caused by the malfunction
of this product (such as costs of photography or any loss of benefit
generated by the photography) is not the responsibility of our company and
no compensation will be given for it.
1.3 Copyright information
Unless agreed by the right owner, all the pictures taken with this digital
camera cannot be used in violation of copyright law. Any transfer of
pictures or memory card with date must be conducted under the
constraints of copyright law.
1.4 Caution when using the camera
This product consists of intricate electrical parts, to ensure the camera
photographs normally, do not drop or hit the camera when taking pictures.
•Avoid using or placing the camera in the following locations:
1. Damp and dusty places
2. Sealed vehicles or places exposed to direct sunlight or places subject to

5
extremely high temperatures or heat
3. Turbulent environment
4. Locations full of smoke, oil fumes or steam
5. In rain or snow environment
•Do not open the battery cover when the power is on
•If water has entered the camera, immediately turn the power off and
remove the batteries.
•How to maintain your camera:
1. If the lens, LCD monitor or viewfinder surface is dirty, please use a lens
brush or soft cloth to wipe the surface clean instead of touching the lens
with your fingers.
2. Do not use any solid object to hit the camera to avoid scratching the
lens, LCD monitor or viewfinder surface.
3. Do not use any detergent or volatile solution, which will subject the
camera case and paint to dissolving or distortion, use soft cloth only.

6
2. Getting to know your DC-302
2.1 Control Reference
1. Flash light
2. Self-time LED
3. Lens
4. Viewfinder
5. USB jack
6. Tripod socket
7. Flash LED
8. Shutter button
9. ON/OFF button
10. Strap bar
11. Battery cover/card slot
12. Up button
13. RIGHT button
14. Menu button
15. Down button
16. Flash button
17. Playback button
18. Display button
19. Left button
20. Monitor screen

7
2.2 Monitor screen display

8
3. Usage preparations
3.1 Load batteries and memory card
Open the battery cover and put in 3 AAA new alkaline batteries according
to the polarity indicated on the battery door, then insert the memory card
(not included in the scope of delivery), close the cover. When the battery is
in low voltage, a selected icon will appear on the screen, you need to select
what kind of battery you are using, if you use alkaline battery, you should
select 1, the battery capacity icon will display half, then you cannot use
flash light, but you can still take photos until the icon displays empty; if you
use rechargeable battery, you should select 2, the battery capacity icon still
display full, you can take photos until the icon display empty.
3.2 Turn ON/OFF the camera
You start the camera when you press the ON/OFF button until the
operation LED lights. Press the ON/OFF button for 2 seconds the camera
will turn off. This camera is designed to automatically power off to save
battery life in 30 seconds to 59 minutes 59 seconds of inactivity if not
connected to USB. The auto power off time can be set in the menu of auto

9
power off function.
3.3 Set up
Taking pictures and recording function
3.3.1 Capture option
Press the menu button and enter the capture select
window, press the UP or DOWN button to select the
capture mode. Then press menu button to confirm your
choice. Press RIGHT button to next menu.
3.3.2 Color option
Press the menu button and enter the capture select
window and press RIGHT button to next menu color. Press
UP or DOWN button to select the item to adjust and menu
button to enter the selected item.

10
Adjusting exposure value:
EV range from -1.5 ~ +1.5
Selecting white balance option:
Adjusting sharpness option:
3.3.3 Resolution
Press the menu button and enter the capture select window and press
RIGHT button to next menu resolution. Press the UP or DOWN button to
select the resolution then press menu button to confirm:

11
Super: 2560 x 1920
High: 2048 x 1536
Middle: 1600 x 1200
Low: 1280 x 1024
3.3.4 Quality
Press the UP or DOWN button to select the quality (High
or Standard) then press menu button to confirm. Press
RIGHT button to next menu.
3.3.5 Auto power off time
Press the menu button and enter the capture select window and press
RIGHT button to next menu Auto power off. Press the DOWN button to set
your choice.

12
3.3.6 Date & Time
Press the DOWN button to
set date and time.
When you choose “DISPLAY”, the date & time will show on the picture,
otherwise choose “NO DISPLAY”.

13
3.3.7 Frequency
In order to take a better indoor picture, the camera needs to be set to suit
the correct lighting frequency. Set the frequency to 60Hz for US and 50Hz
for Europe.
3.3.8 Language
Press the UP or DOWN button to select the language then
press menu button to confirm your choice.
3.4 Playback function
Press the Playback button to select the playback mode
3.4.1 Erase
Press the menu button to enter the erase window,
press the UP or DOWN button to select "One”
or "All". Press menu button to confirm your choice.

14
Select the format mode and format the
memory card inside the camera.
Select the protected mode and protect
the frame selected.
If you want to unprotect the frame,
select the frame, then enter the
erase mode; select unprotected
mode. Press RIGHT button to enter
the next menu.

15
3.4.2 Auto power off time
Press the DOWN button to set your choice.
3.4.3 Date & Time
Press the DOWN button to
set your choice.
When you choose “DISPLAY”, the date & time will show on the picture,
otherwise choose “NO DISPLAY”.

16
3.4.4 DPOF (Digital Print Order Format)
”DPOF” stands for “Digital Print Order Format”, which is a format for
recording on a memory card or other medium which captured images
and how many copies should be printed. Then you can print on a DPOF
compatible printer or at a professional print service from the memory card
in accordance with the file name and number of copies settings recorded
on the card.
3.4.5 Rotation
Press UP or DOWN button to select the rotation angle and
menu button to enter the selected angle.
3.4.6 Zoom/ PAN
In the single picture preview mode, the PAN function
can be used to move the display range of the image

17
after image has been enlarged in zoom mode. In the ZOOM / PAN menu,
press the DOWN button to enter the PAN function and menu button to
confirm the setting. Now press UP/ DOWN/ LEFT/ RIGHT button to move
the display range of the picture. To cancel the PAN function, press the
menu and then DOWN button to exit.
3.5 Using your DC-302
3.5.1 Take pictures
You just press the shutter button down and with a distinct beeping sound, a
snapshot is finished. At the same time, the number on the monitor screen
will decrease by one.
3.5.2 Self-timer
Press the menu button into the menu, change to the self-timer mode, after
that press the menu button to confirm. Press the shutter button, the
self-timer LED will blink for 10 seconds and then capture a picture.

18
3.5.3 Take video
Press the menu button into the menu and change to the video mode. Press
the menu button to confirm your choice. Press the shutter button to start
recording. Press the shutter button again to stop recording.
3.5.4 Use the flash
Press the flash button into the FLASH AUTO or ON mode, the camera will
charge the flash; the monitor screen will be close and the operation LED
will blink. When LED stops blinking and the monitor screen turns on, the
charging is done. The FLASH ON function will always fire the flash, the
FLASH AUTO function will fire automatically as needed. When the shutter
button is pressed, the flash will fire.
3.5.5 Use the digital zoom
In the REC mode you can use the digital zoom. Before taking videos press
the UP button to zoom in, press the DOWN button to zoom out.

19
3.5.6 Playback mode
Press the playback button to come to the playback mode. You can view up
9 pictures and video clip files on the LCD screen. Press the DISPLAY
button and up to 9 files appear on the screen. In the one picture mode,
press the UP or DOWN button and zoom in or zoom out of the picture. If a
video is selected in the nine picture mode, press the DISPLAY button and
playback of the video starts.
3.5.7 Download
Turn the camera on to the preview mode and connect the camera to the
computer via a USB cable. In Windows 2000/ME/XP/VISTA, there is no
need to install the driver. Connect the camera to PC. The LCD screen will
display MSDC and the camera will be recognized as a removable FLASH
DISK. You can directly copy the pictures from the camera to your computer.
3.5.8 How to use the PC camera function
Install the camera driver from the CD. Connect the camera to the computer
with a USB cable, run the program Amcap under the folder <Sunplus

20
Ca533> in the program, select the device as Sunplus SPCA533.
After that select Options as Preview.