aidios M1 User manual

User manual v1.0

1. Safety instructions and warnings ………….…………….1
2. Overview
2.1. Inside the box …………………………………………………2
2.2. Specification ………………………………………………2-3
2.3. Product overview ..……………………………………………….4
3. Getting started
3.1. Charging and powering monitor unit ……………………………5
3.2. Powering camera unit ……………………………………………6
4. Operation –General mode
4.1. OSD icons ……………………………………………………………7
4.2. Control keys …………….…………………….………………….8
5. Operation –Menu mode
5.1. Video category ……………………………………………….…..9
5.2. Audio category ……………………………………………….…10
5.2.1. Auto mute …………………………………………………...10
5.2.2. VOX …………………………………………………………...11
5.3. Camera category ……………………………………………….11
5.3.1. Add a camera unit ……………………………………………12
5.3.2. Auto scan ………………………………………………….…12
5.3.3. Picture in picture (PiP) ……………………………………….13
6. Troubleshooting and tips ………………………….….14-16
7. Warranty information …………………………………….17
8. FCC statement ……………………………………………18
9. Declaration of conformity / Others ……………………19

1
Please read and follow all instructions and warnings in this user manual
before using the product.
◼Strangulation Hazard - Keep the adapter cord out of the reach
of children. Never place the camera or cord within 3 feet of a crib
or playpen.
◼Choking Hazard - This product contains small parts which may
cause choking. Not for children under 3 years.
◼Risk of explosion if battery is replaced by an incorrect type.
Dispose of used battery according to the instructions.
◼Use ONLY the power adapters and battery supplied with this
product. Using other 3rd parties power adapter or battery may
cause fatal damage to the product.
◼Protect the adapter cord. Route cord so that they are not walked
on or pinched by items or against them.
◼Keep all components away from water or heat source such as a
sink, bath tub, laundry tub, fire place or stove.
◼Provide proper ventilation for both monitor and camera unit. Do
NOT cover them with any material, such as a blanket or cloth.
◼Disconnect all A/C adapters before cleaning. Do NOT immense in
water. Clean it only with a dry cloth.
◼Do NOT attempt to open the devices or accessories. No user
serviceable part inside. Risk of electrical shock, fire or death.
◼This product is NOT a substitute for direct supervision of your
baby. Check your baby's activities at regular intervals.
◼This product is not a toy. Do NOT allow children to play with it.

2
2.1. Inside the box
Thanks for purchasing aidios M1 wireless monitoring system. It
contains below components :
Monitor unit x 1
Camera unit with stand x 1
Rechargeable Lithium battery x 1
A/C adapters x 2
Mounting screw x 1
Adhesive rubber foot x 4
User manual x 1
2.2. Specification
RF frequency
2400 –2483.5 MHz
Type of modulation
GFSK
Type of spread spectrum
FHSS
Data rate
4 Mbps
Channel width
4 MHz
Transmission range
>1000 feet (LOS)

3
Monitor unit
Display
4.3” color LCD at 480x272
Audio
Built-in speaker and microphone
Battery
1800mAh Lithium rechargeable
Duration (screen on)
~10 hours
Duration (VOX on)
~18 hours
Operating voltage
5V
Camera unit
Picture sensor
1/5” Color CMOS, 640x480
Optical lens
F2.4, EFL 2.5mm, FOV 70∘
Night vision
8 x 940nm IR LEDs
Light sensor
Built-in
Audio
Built-in speaker and microphone
Operating voltage
5V
A/C adapter
Battery
Mfg.
Dongguan Guanjin
Electronics Technology
Co., Ltd.
Shenzhen Blue Sea Excellent
New Energy Co., Ltd.
Model #
K05B050100 series
FT525068P-1800mAh
Spec.
Input 100-240V AC
50/60 Hz
Output 5.0V DC 1.0A
3.7V 1800mAh 6.66Wh

4
2.3. Product Overview

5
3.1. Charging and powering monitor unit
Loosen the screw and open battery door. Plug in the battery to
the battery socket as shown in pic. 1. Close the battery door
and tighten the screw.
Plug the power adapter into an electrical outlet. Insert the
3.5mm plug to the power jack as shown in pic. 2 . The charging
process starts and charge LED indicator emits red light.
Press and hold the power button for 1 second to turn on the
monitor unit. Power LED indicator emits blue light when monitor
unit is turned on.

6
3.2. Powering camera unit
Plug the power adapter into an electrical outlet. Insert the
3.5mm plug to the power jack as shown in pic. 3 . Slide the
power switch to 'ON' position to turn on the camera unit. Power
LED indicator emits blue light when camera unit is turned on.
NOTE :
-Do not injest battery, Chemical Burn Hazard.
-This product contains a Lithium cell battery. If the battery is
swallowed, it can cause severe internal burns in short period and
can lead to death.
-Keep new and used batteries away from children.
-If the battery compartment does not close securely, stop using the
product and keep away from children.
-If you think battery might have been swallowed and placed inside
any part of body, seek immediate medical attention.

7
4.1. OSD icons
Camera icons :
Standard camera unit
Camera unit at zoom mode
Camera unit with pan tilt docking
(*) Temperature reading icon will be displayed only when pan tilt docking
is installed.

8
4.2. Control keys
Power button
Press and hold : Power on/off
Short press : video off mode (audio only)
(*) Pan tilt mode only available when pan tilt docking is installed.

9
To enter menu mode, press ‘Enter’ key once. To leave menu mode, press
‘Exit’ key once. In menu mode, press arrow keys to navigate and select
different options.
Note : Some functions require pressing ‘Enter’ key to perform the action,
which will be shown in function description column.
5.1. Video category
Brightness
Adjust brightness of LCD screen
Color Saturation
Adjust saturation level of video image
Night vision
Select different night vision modes
Zoom
Display enhanced zoom image
Sound bar
Display sound bar on screen to show sound
level.

10
5.2. Audio category
Camera# volume
Adjust sound output of registered camera
(for 2 way talk, lullaby and nature sound)
Low battery alert
Toggle low battery alert on/off (2 beeps)
Out of range alert
Toggle out of range alert on/off (1 beep)
Auto mute
Toggle auto mute on/off (3 sensitivity levels)
VOX
Toggle VOX on/off (3 sensitivity levels)
Camera # lullaby
Toggle lullaby on/off for registered camera
Camera # nature
sound
Toggle nature sound on/off for registered
camera
5.2.1. Auto mute
When auto mute is enabled, the camera unit starts to detect noise level.
It turns off audio completely after a 10 seconds of continuous silence.
Any noise detected afterwards will trigger the audio system back on, and
repeat the noise detection.
The pre-determined level of silence can be adjusted over sensitivity
setting. High sensitivity setting works better at silent condition. Low
sensitivity setting works better at noisy condition.
Note : When auto mute is enabled, VOX function will be disabled
automatically.

11
5.2.2. VOX
Alike auto mute function, the camera unit starts to detect noise level
when VOX is enabled. It turns off both video and audio completely after
a 10 seconds of continuous silence. Any noise detected afterwards will
trigger both systems back on, and repeat the noise detection.
Sensitivity setting is the same as auto mute function mentioned
in 5.2.1.
Note : When VOX is enabled, auto mute function will be disabled
automatically.
5.3. Camera category
Camera#
View, pair and or delete camera pairing for
each camera
Auto scan
Cycle all registered cameras at an interval of
10 seconds.
Picture in picture
Display video image of secondary camera at
bottom right corner of screen

12
5.3.1 Add a camera
1. Select an ID for your new camera and move the cursor to this camera
ID.
2. Press left/right arrow key and select 'Pair' option.
3. Press 'Enter' key to perform pairing process.
4. Press and hold the 'Pair' button at the back of camera unit for 1 second.
The power LED of camera unit will blink to indicate pairing mode.
5. Pairing process will be started automatically. Upon pairing success,
the screen will display a message to indicate if the pairing process is
completed.
6. If unsuccessful, delete the pairing and retry above process.
5.3.2 Auto scan
Auto scan function automatically cycles through all registered cameras
and display each camera for 10 seconds. If only one camera is registered,
the screen will only display video from the registered camera.
Note : When auto scan is enabled, VOX and auto mute will be
disabled temporarily until auto scan is disabled.

13
5.3.3 Picture in picture (PiP)
Picture in picture function allows viewing 2 camera units simultaneously.
The video image of primary screen will be displayed at normal size. The
video image of secondary screen will be reduced to 1/3 of its original
size and displayed at lower right corner of screen. No audio will be
transmitted from the camera at secondary screen.
Camera number of secondary screen can be changed by pressing 'Left'
arrow key at general mode
Note : When picture in picture is enabled, activation of VOX and auto
mute function will depends on the sound level of camera at primary
screen.
Note : When both auto scan and picture in picture are enabled, the
camera at secondary screen will be cycled at every 10 seconds

14
Problem
Solution
Product does not
switch on
1. Check the power adapter is properly
connected to the device and wall outlets.
2. Swap the power adapter to check if the
problem is caused by a defected adapter.
3. Double check if the monitor unit and
camera unit is powered on. (Refer to
section 3 of this user manual)
Screen shows 'Signal
lost ! Establishing
connection'
It indicates that the monitor unit cannot
communicate with the camera unit.
'1. Check the current camera number if it is
correct. The camera number is displayed
at the camera icon located at top left corner
of screen.
2. If you are not sure about the camera
number, press left arrow key to cycle
through each camera from number 1 to 4.
3. Make sure the camera is powered on.
The blue power LED should be lighted up.
4. If all fail, it may due to connection issue.
Please check below column for the tips.
Connection issues
Below are the tips to improve the
connectivity between monitor and camera
unit
1. Place both monitor and camera unit 3
feet above ground.
2. Flip the antenna out of the monitor unit.

15
Connection issues
(continued)
3. Place the monitor and camera units
closer, if possible.
4. Avoid large metallic objects in close
proximity to the monitor or camera unit.
5. Place the monitor or camera unit at
least 3 feet from any 2.4GHz device, such
as WiFi router, smartphone or microwave
oven.
6. Try to delete the pairing at the monitor
unit, and re-pair to the camera unit.
7. Try to enable smart channeling and use
different band to test connectivity.
Screen shows black
and white image, not
color image
It is normal that the system delivers black
and white image at night vision mode.
1. Relocate the camera unit, so to capture
correct ambient light level.
2. Select a low sensitivity night vision
setting.
3. Night vision can be enabled or disabled
manually in menu mode.
Feedback noise (shrill
sound)
1. Avoid to put monitor and camera unit
too close together.
2. Decrease volume level of monitor unit.
Sound cut in and out
1. Possibly due to auto mute function.
Turn off auto mute function and test.
2. Unit at marginal reception condition.
Try solutions in connection issues column.

16
Annoying beep
alerts
There are 2 types of beep alerts, low
battery and out of range.
System delivers one beep every 10 seconds
if the monitor cannot communicate with
camera unit.
System delivers two beeps every 10
seconds if the battery capacity is low.
Both alerts can be enabled or disabled in
user menu.
Battery and charging
issue
For first time usage, it is always
recommended to charge the battery for at
least 8 hours before power on. Avoid to dry
up the capacity before recharging, as it
degrades the battery and shorten its life
cycle.
1. During battery charging, the red charge
LED should be lighted up. Check the power
adapter and make sure it is properly
connected to monitor unit and wall outlet.
2. Swap the power adapter to check if the
problem is caused by a defected adapter.
3. Plug the power adapter to other wall
outlet/power source.
4. Remove the battery from monitor unit,
and re-insert it. Check the connection pins
if they are in good condition.

17
We warrant to the original user that the product is free from material
and workmanship defects for a period of one (1) year from the date of
original purchase. If this monitoring system fails to function properly
when used as directed under normal condition within the one year period,
we will either repair or replace the product, at our discretion, free of
charge.
This warranty does not apply to a product which has been damaged as
a result of improper maintenance, accidents, improper voltage supply,
or other misuses. The warranty is also void if the owner repairs or
modifies the product in any way. We are not liable for any incidental or
consequential damages with regard to this product. The warranty also
excludes any liability other than what is stated above. No other
warranties are given.
Legal rights vary from country to country. Some countries do no allow
the exclusion or limitation of incidental or consequential damages, so
the above limitation may not apply to you.
If you experienced any problem and the troubleshooting can not help
you to solve the problem, please visit our website for an updated FAQ
or contact us directly. We are always pleased to serve you at the best
we can.

18
WARNING : Modifications not authorized by the manufacturer may void
users authority to operate this device.
This device complies with part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate the
equipment.
This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of FCC Rules. These limits
are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to
radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The camera unit shall be installed and operated with a minimum distance
of 20cm between the radiator and your body.
Please refer to the appendix for the SAR statement.