d. Repeat steps ‘a’ through ‘c’ for all four holes in the
base plate.Tighten all bolts securely.
7. To mount a pan/tilt or scanner device:
a. The slotted mounting holes on the T9207, T9214
or T9224 can accommodate the following mount-
ing hole dimensions of pan/tilts and scanners:
ax. in.
Bolt Circle 197 mm (7.75 in) 121 mm (4.75 in)
Square Centers 140 mm (5.50 in) 85 mm (3.36 in)
b. To install, line up the holes in the base mounting
plate of the device. Insert a minimum of four
machine bolts (not included) with flat washers
through the device and the end flange of the
T9207, T9214 or T9224; then securely fasten
using lock washers and nuts.
4.2 MT9216 409-mm (16-inch) and
MT9222 564-mm (22-inch)
Wall Mounts
3
6. To mount the T9227 Adjustable Head Bracket to:
MT9216 Wall Mount
a. Use the 1/4-20 threaded mounting hole located in
the center of the slot pattern.
b. Insert a 1/4-20 hex head machine bolt, washer, and
lock washer through the adjustable head and into the
threaded insert in the wall mount. The bolt should
be 20 mm (3/4 in) long. A lock washer and a flat
washer must be used under the head of the bolt.
MT9222 Wall Mount
a. Line up the hole in the T9227 base plate with the
center mounting hole on the mounting bracket.
b. Insert a bolt with flat washer through the T9227
base plate and mounting bracket. A
5/16-18 x 50 mm (2-in) long bolt (not supplied) is
recommended to fasten the T9227 to the mount-
ing bracket.
c. From the underside of the mounting bracket, use a
lock washer and nut to secure the T9227.
Temporarily leave hand tight.
7. To mount the T9237 Heavy Duty Adjustable Head
Bracket to the T9216 or the T9222 Wall ounts:
a. Line up the holes in the corners of the T9237 base
plate with the slots in the flange bracket.
b. Insert a 3/8-16 x1” hex bolt through the base plate
and flange bracket, using a flat washer and a 3/8” flat
washer and 3/8” sprial lock washer under the head
of the bolt.
c. From the underside of the flange bracket, use a 3/8”
flat washer and 3/8-16 hex nut to secure the
T9237 to the mounting flange.
d. Repeat steps ‘a’ through ‘c’ for all four holes in the
base plate.Tighten all bolts securely.
8. To mount a pan/tilt or scanner device:
a. The slotted mounting holes on the T9216 and
T9222 can accommodate the following mounting
hole dimensions of pan/tilts and scanners:
Max. Min.
Bolt Circle 197 mm (7.75 in) 121 mm (4.75 in)
Square Centers 140 mm (5.50 in) 85 mm (3.36 in)
b. To install, line up the holes in the base mounting
plate of the device. Insert a minimum of four
machine bolts (not included) with flat washers and
lock washers through the device and the mounting
plate of the wall mount; then securely fasten using
lock washers and nuts.
1. Determine a secure wall mounting location.
WA NING: Do not mount in an inverted
position.
2. Caution:
a. For a secure installation use six (6) bolts (not
included). The bolts should extend through the
mounting surface and be secured with nuts, lock
washers, and flat washers on the opposite side.
b. If studs are used, they should be anchored in
concrete or welded to a steel backer plate.
c. If the wall mount is attached to wood or to a blind
structure (with no access to the rear), make certain
that the mounting fasteners have a minimum pull-
out strength of 600 pounds.
3. For ease of installation, locate the bottom mounting holes
first. Install the bolts (or studs) into the wall surface.
WA NING:The MT9216 and MT9222 must
be mounted with the slotted mounting holes of
the wall plate at the bottom.
4. Reseat the T9216 or T9222 on the bolts (or studs)
using the bottom slotted holes, then locate the upper
mounting holes and drill into the wall surface.
5. Install the upper bolts (or studs) through the wall mount
and into the wall surface. Tighten upper and lower bolts
(or studs) securely.
Note:The minimum diameter bolt (or stud) required is
10 mm (3/8 in).
