Aiphone RY-IP44 Owner's manual

RY-IP44
Programming Manual
For use with the IPW-1A
1218
Input/Output Network Adaptor
This manual is for programming the RY-IP44 with the IPW-1A only. Refer to the IPW-1A
Installation and Operation Manuals for complete installation/programming information.
For instructions featuring the RY-IP44 with the IX2 Series, visit www.aiphone.com/IX2-RYIP44
For instructions featuring the RY-IP44 with the IS IP Series, visit www.aiphone.com/ISIP-RYIP44
ATTENTION:

• RY-IP44
• Programming Manual
• 6 Screw Terminal Blocks
• MAC Address Label
Overview / Description
2 | RY-IP44 Programming Manual
Package Contents
The RY-IP44 is a Barix Barionet 50 with proprietary rmware installed for the device to function with the Aiphone
IPW-1A system.
The 4 relay outputs can be programmed to trigger for door release, while calling, while communicating, or while calling
and communicating.
The RY-IP44 is not a PoE device and requires a dedicated 9-30V DC power supply. Use the Aiphone PS-1208UL
power supply (sold separately).
• General understanding of IPW-1A programming
• 9-30V DC power supply (sold separately)
• Unique IP address for each adaptor
Installation Requirements
Conguring the RY-IP44 (assigning IP address and system use)
Relay status and control.
Click on each LED to verify
relay function.
Digital input status
Conguration button
The RY-IP44 has a default IP address of 192.168.1.45. Open a web browser and point the address bar to 192.168.1.45
for access to the adaptor. The rst screen to appear will be the Device Status screen.
Click the CONFIGURATION button to open the Device Conguration screen. This is where a unique IP Address,
Netmask, and Gateway can be assigned to the adaptor. Consult with your IT department for these settings.
Settings not utilized for Aiphone
functionality. Do not adjust.
SECURITY: For creating a password for
access to the web browser interface.
AIPHONE: Select the Aiphone system
type the relay is to be used with.
Enter new IP Address if default is not
to be used.

3
The Aiphone system type that the adaptor is being integrated with will need to be selected. Click the AIPHONE tab. Use
the drop down by System Type to select the IPW-1A system. Enter a UDP Protocol Port number or leave at 0 to use the
default (1724). When done, click OK. Click Reboot on the next screen to restart the adaptor.
System Type: Select IPW-1A
UDP Protocol Port: Enter “0” if default port
(1724) is to be used. Port 1724 is the default port
on the IPW-1A stations for UDP messaging.
The RY-IP44 has 4 relays that can be programmed to trigger while calling, while in communication, or while calling and
communicating with a specic door station. The relays can also be programmed for door release.
Relay Action options:
• Door Release - Normally-Open
• Door Release - Normally-Closed
• Active while Calling from source
• Active while in Communication with source
• Active during Calling and Communication
• A
ctive While Any Station Calling
*Relay will trigger when the PC master station pushes the door release button.
}
Relay will trigger when the associated door station calls or communicates.
}
Relay triggers when any station calls. No assignment required.
}
IN0 IN1 NO C NC
* When using the RY-IP44 for door release, the relay on the IPW-1A must be set to door release and the relay
must be jumpered to the sensor input as shown below.
Relay Output Programming
Application Setup button
From the Device Conguration screen, click APPLICATION SETUP.
Conguring the RY-IP44 (continued)

4 | RY-IP44 Programming Manual
Enter the Station ID for the IPW-1A to be associated with each relay on the RY-IP44. Select the relay condition from the
Relay Action drop down menu. When done, click on Apply Settings. Click Reboot on the next screen to restart the
adaptor with the applied settings.
RY-IP44 Wiring
Aiphone Corporation
www.aiphone.com
[email protected]
800-692-0200
RY-IP44 Dimensions
4-1/8”
3-5/16”
Mounting:
The RY-IP44 adaptor mounts to an Aiphone
W-DIN11 mounting rail (sold separately).
Depth:
1-1/4”
Door release: External signaling:
Power:
Use a 9-30V DC (300mA @ 12VDC)
power supply to power the RY-IP44
adaptor.
Use the Aiphone
PS-1208UL power supply (sold
separately).
R1
NO
R3
NO
PT
Door
Strike Bell
= Power Transformer (use proper power for the strike, mag lock, or external signaling device being used).
PS-1208UL
PT
PT
R2
NO
R4
NO
R1
NO
R3
NO
R2
NO
R4
NO
+
-
+
-
{
{
{
{
Relay 1
Relay 2
Relay 3
Relay 4
{
{
{
{
Relay 1
Relay 2
Relay 3
Relay 4
{
Power
Relay contact rating: 30V DC, 0.5A.
FCC WARNING:
This device complies with Part 15 of the FCC rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference that may cause undesired operation.
• For proper regulatory compliance, the drain wire should be disconnected at the power supply end of the cable.
• Changes or modications not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
Relay Output Programming (continued)