Air King SEVILLE SERIES Instruction Manual

www.airkinglimited.com
000000000 Rev A. 5-08 1 of 20
READ AND SAVE THESE INSTRUCTIONS
READ CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE, INSTALL, OPERATE OR MAINTAIN THE PRODUCT DESCRIBED. PROTECT
YOURSELF AND OTHERS BY OBSERVING ALL SAFETY INFORMATION. FAILURE TO COMPLY WITH
INSTRUCTIONS COULD RESULT IN PERSONAL INJURY AND/OR PROPERTY DAMAGE!
RETAIN INSTRUCTIONS FOR FUTURE REFERENCE.
GENERAL SAFETY INFORMATION
When using electrical appliances, basic precautions
should always be followed to reduce the risk of fire,
electric shock and injury to person, including the following:
WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK
AND INJURY TO PERSON, OBSERVE THE FOLLOWING:
1. Read all instructions before installing or using range hood.
2. Use this unit only in the manner intended by the manufacturer. If
you have questions, contact the manufacturer.
3. Before servicing or cleaning the unit, switch power off at service
panel and lock the service disconnecting means to prevent power
from being switched on accidentally. When the service
disconnecting means cannot be locked, securely fasten a prominent
warning device, such as a tag, to the service panel.
4. Installation work and electrical wiring must be done by qualified
person(s) in accordance with all applicable codes and standards,
including fire-related construction.
5. Sufficient air is needed for proper combustion and exhausting of
gases through the flue (chimney) of fuel burning equipment to
prevent back drafting. Follow the heating equipment manufacturer’s
guideline and safety standards such as those published by the
National Fire Protection Association (NFPA) and the American
Society for Heating, Refrigeration, and Air Conditioning Engineers
(ASHRAE), and the local code authorities.
CAUTION: FOR GENERAL VENTILATING USE ONLY. DO NOT USE
TO EXHAUST HAZARDOUS OR EXPLOSIVE MATERIALS AND VAPORS.
6. When cutting or drilling into wall or ceiling, do not damage electrical
wiring and other hidden utilities.
CAUTION: TO REDUCE THE RISK OF FIRE AND TO PROPERLY
EXHAUST AIR, BE SURE TO DUCT AIR OUTSIDE - DO NOT VENT
EXHAUST AIR INTO SPACES WITHIN WALLS OR CEILINGS OR INTO
ATTICS, CRAWL SPACES, OR GARAGES.
7. This unit must be grounded.
8. To avoid motor bearing damage and noisy and/or unbalanced
impellers, keep drywall spray, construction dust, etc. off power unit.
Seville™ Series Range Hood
SAVE THESE INSTRUCTIONS
WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, DO
NOT USE THIS FAN WITH ANY SOLID-STATE SPEED CONTROL DEVICE.
WARNING: TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:
a) Never leave surface units unattended at high settings. Boilovers
cause smoking and greasy spillovers that may ignite. Heat oils
slowly on low or medium settings.
b) Always turn hood ON when cooking at high heat or when
flambéing food (ie. Crepes Suzette, Cherries Jubilee, Peppercorn
Beef Flambé).
c) Clean ventilating fans frequently. Grease should not be allowed
to accumulate on fan filter.
d) Use proper pan size. Always use cookware appropriate for the
size of the surface element.
WARNING: TO REDUCE THE RISK OF INJURY TO PERSONS IN
THE EVENT OF A RANGE TOP GREASE FIRE, OBSERVE THE FOLLOWING:
a) SMOTHER FLAMES with a close-fitting lid, cookie sheet, or
metal tray, then turn off burner. BE CAREFUL TO PREVENT
BURNS. If the flames do not go out immediately, EVACUATE
AND CALL THE FIRE DEPARTMENT.
b) NEVER PICK UP A FLAMING PAN - You may be burned.
c) DO NOT USE WATER, including wet dishcloths or towels - a
violent steam explosion will result.
d) Use an extinguisher ONLY if:
I. You know you have a Class ABC extinguisher, and you already
know how to operate it.
II. The fire is small and contained in the area where it started.
III. The fire department is being called.
IV. You can fight the fire with your back to an exit.
WARNING: TO REDUCE THE RISK OF FIRE, USE ONLY METAL
DUCTWORK.
IMPORTANT INSTRUCTIONS -
OPERATING MANUAL

CAUTION: MAKE SURE THE SURFACE YOU ARE MOUNTING THE
POWER UNIT TO IS CAPABLE OF SUPPORTING THE WEIGHT OF THE UNIT.
OTHERWISE YOU WILL NEED TO REINFORCE THE AREA.
SECTION 3
Ducting
CAUTION: ALL DUCTING MUST COMPLY WITH LOCAL AND NATIONAL
BUILDING CODES.
WARNING: TO REDUCE THE RISK OF FIRE, USE ONLY METAL DUCTWORK.
1. Install the included duct collar to the hood with two of the provided 3 x 11
mm screws (Figure 3).
2. Connect the ducting to the duct collar and secure in place using tape to
seal all joints (Figure 3).
NOTE: The duct connector is 5.8" in diameter (for 6" round ducting) and the
center is located 3-3/16" inches from the back wall.
CAUTION: ALWAYS DUCT THE FAN TO THE OUTSIDE THROUGH A
WALL OR ROOF CAP.
SECTION 4
Wiring
CAUTION: ALL ELECTRICAL CONNECTIONS MUST BE MADE IN
ACCORDANCE WITH LOCAL CODES, ORDINANCES, OR NATIONAL ELECTRICAL
CODE. IF YOU ARE UNFAMILIAR WITH METHODS OF INSTALLING ELECTRICAL
WIRING, SECURE THE SERVICES OF A QUALIFIED ELECTRICIAN.
1. Attach the wire compartment to the power unit with two of the provided
3 x 11 mm screws. Remove the wire compartment cover and connect the
white wire (on some models this wire will be brown) from the power unit
to the white wire from the supply. Connect the black wire (on some models
this wire will be blue) from the power unit to the black wire of the supply.
Connect the ground wires from the home (green or bare) and the power
unit (green/yellow) to the grounding screw in the wire compartment. Use
approved methods for all connections (Figure 4).
www.airkinglimited.com
000000000 Rev A. 5-08
INSTALLATION INSTRUCTIONS
CAUTION: MAKE SURE POWER IS SWITCHED OFF AT SERVICE PANEL
BEFORE STARTING INSTALLATION.
SECTION 1
Preparing the Range Hood
1. Unpack hood from the carton and confirm that all pieces are present. In
addition to the range hood you should have:
1 - Package containing:
1 - duct collar
4 - 3 mm x 11 mm mounting screws
4 - 4 mm x 15 mm mounting screws
24 models: 2 - Aluminum Grease Filters (shipped installed)
30 models: 3 - Aluminum Grease Filters (shipped installed)
2 -50 watt Halogen lamps
1 - Instruction/Safety Sheet
NOTE: Some hoods may be shipped with a protective plastic adhered to the
underside of the unit. It is recommended to leave this in place during installation
to protect it from scratching. Remove when the installation is complete.
SECTION 2
Installing the Range Hood
CAUTION: MAKE SURE POWER IS SWITCHED OFF AT SERVICE PANEL
BEFORE STARTING INSTALLATION.
CAUTION: WHEN CUTTING OR DRILLING INTO WALL DO NOT DAMAGE
ELECTRICAL WIRING AND OTHER HIDDEN UTILITIES.
1. Cut an appropriate size hole into the cabinet or canopy the power unit will
be mounted into (Figure 1):
SEV24SS models: 18" wide by 10" deep.
SEV30SS models: 30" wide by 10" deep
NOTE: If you will not have access to the ducting or wiring once the hood is installed
into the cabinet or canopy, make the ducting and electrical connections at this
point by referring to the
SECTION 3 and SECTION 4 of this instruction sheet.
NOTE: If an optional hood liner is being utilized, install at this point according
to the instructions included with the liner.
2. Insert the power unit into the hole and secure in place using the four
provided 4 x 15 mm mounting screws (Figure 2).
2 of 20
Figure 3
Ducting
Duct Collar
Power Unit
Figure 1
18" or 30"
10"
Figure 2

www.airkinglimited.com
000000000 Rev A. 5-08
2. Replace the wire compartment cover and tighten screws. Make sure all
wiring is securely contained within the wire compartment.
SECTION 5
Finishing the Installation
1. Remove any protective plastic adhered to the power unit.
2. Install two PAR16, 45W maximum lamps by inserting lamp into socket and
turning clockwise until lamp is firmly seated. DO NOT over tighten.
3. Turn switches to the OFF ( ) position and restore power. Test that the
light and the fan are operating properly.
4. If there is any vibration noise, check for the source and try to tighten
fasteners or adjust the tape to make a tighter connection or seal.
SECTION 6
Operation
Controls
Your Range Hood is equipped with two sliding switches with one controlling the
lighting and the other controlling the exhaust fan. The light control has two
positions, ON ( ) and OFF ( ). The fan is a four position control, HIGH (III),
MEDIUM (II),LOW (I), and OFF ( ) (Figure 11).
SECTION 7
Maintenance
CAUTION: MAKE SURE POWER IS SWITCHED OFF AT SERVICE PANEL
BEFORE SERVICING THE UNIT.
Filters
1. Included with your unit are aluminum grease filters that should be washed
at least once a month. The filters are dishwasher safe and should be
washed in a mild soap or detergent.
2. To remove the filters, pull down on the handle tab until the filter releases
from the unit. To reinstall, slide tab at rear of filter into slot in the unit. While
holding in handle of filter, lift filter into place and release handle. The filter
should snap securely into place (Figure 6).
NOTE: If your model is equipped with a filter screw, slide tab at rear of filter into
slot in hood and secure filters in place by tightening screw located at front of
filter. DO NOT OVERTIGHTEN.
3. If the grease filters become damaged, replace with the Air King Model
BCGF-01 Grease Filters.
Cleaning
CAUTION: DO NOT USE GASOLINE, BENZINE, THINNER, HARSH
CLEANSERS, ETC., AS THEY MAY DAMAGE THE RANGE HOOD.
1. Clean your power unit with a mild detergent, such as dishwashing liquid,
and dry with a soft cloth. NEVER USE ANY ABRASIVE PADS OR SCOURING
POWDERS. Completely dry before restoring power. NEVER IMMERSE
ELECTRICAL PARTS IN WATER.
2. The fan assembly can be vacuumed when build up (dirt, lint, etc.)
accumulates over time. The fan is permanently lubricated and does not
require oiling.
3 of 20
Troubleshooting Guide
Trouble Probable Cause Suggested Remedy
1. Hood does not operate when the switch is on. 1a. A fuse may be blown or a circuit tripped. 1a. Replace fuse or reset circuit breaker.
1b. Wiring is not connected properly. 1b. Turn off power to unit. Check that all wires are connected.
2. Hood is operating, but air moves slower than normal. 2. Obstruction in the exhaust ducting. 2. Check for any obstructions in the ducting including filter.
3. Hood is making a rattling noise. 3a. Filters are loose. 3a. Turn off power to unit. Check that all filter screws are fully tightened.
3b. Duct connection is loose. 3b. Turn off power to unit. Check that duct connection is tight.
Figure 5
Figure 4
Grounding Screw
Hot (Black)
From Hood
Supply from home
White
WhiteGround Hot (Black)
Wire
Compartment
Figure 6
Tab

000000000 Rev A. 5-08 www.airkinglimited.com
LIMITED WARRANTY
All products manufactured by Air King Limited are warranted for one year from the date of purchase against defects in workmanship and/or material. In addition, all ventilating/exhaust
fans, heaters, combination fan lights and/or heaters, and range hoods are guaranteed for five years from the date of purchase against defects in workmanship and/or material.
This warranty does not cover any labor or shipping costs or the cost of replacement components as part of routine maintenance such as: range hood grease filters, charcoal
filters or combination charcoal/grease filters; replacement light bulbs in range hoods or bathroom fan/light/bulb heater combinations. As well, any damage or failure caused by
abuse, misuse, abnormal usage, faulty installation, or improper maintenance will not be covered by this warranty.
In order to make a claim on this warranty, you must be the original consumer of the product. You will be required to present to Air King the original bill of sale showing: date of
purchase, place of purchase and model purchased. Failure to meet these requirements will void your warranty.
Air King will not be held responsible for any bodily injury or damages to personal property or real estate whether caused directly or indirectly by the product. Some states and
provinces do not allow the exclusion or limitation of incidental or consequential damages and some states do not allow limitations on how long an implied warranty lasts, so these
exclusions or limitations may not apply to you. This warranty gives you specific legal rights and you may have other rights which vary from state to state and province to province.
FOR PARTS OR TECHNICAL ASSISTANCE
Please call: 1-800-465-7300, MONDAY THROUGH FRIDAY, BETWEEN THE HOURS OF 8 AM AND 4:00 PM EST.PLEASE DO NOT RETURN PRODUCT TO PLACE OF PURCHASE.
Reference the type and style of product (located on label inside of the product) when you call. For more information please visit our website: wwwairkinglimited.com
4 of 20
# Qty. Description Replacement Part #
22 1 Capacitor 5S6113094
23 1 Terminal Strip 5S6113095
24 1 Wire 5S6113096
25 2 Filter (SEV30 models Qty. 3) 5S6113028
26 2 Lamp Holder 5S6113097
27 1 Gasket 5S6113098
28 4 Mounting Screws 5S6113099
# Qty. Description Replacement Part #
1 1 Collar 5S6113014
2 1 Body - SEV24 5S6113017
1 Body - SEV30 5S6113020
3 2 Wire Clamp 5S6113012
4 1 Damper 5S6113082
5 2 Damper Springs 5S6113083
6 2 Washer 5S6113009
7 1 Wire Compartment 5S6113010
8 1 Wire Compartment Cover 5S6113011
9 1 Wire Compartment Barcket 5S6113012
10 1 Wire Clamp 5S6113013
11 1 Control Panel Plate 5S6113084
12 1 Control Panel Compartment 5S6113085
13 1 Motor Switch 5S6113086
14 1 Light Switch 5S6113087
15 1 Motor Grill 5S6113088
16 1 Shock Absorber 5S6113089
17 1 Motor Mounting Bracket 5S6113090
18 1 Motor 5S6113091
19 1 Fan Blade 5S6113071
20 1 Motor Housing 5S6113092
21 1 Motor Connection Box 5S6113093
1
2
3
5
4
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
Installer: _________________________________________________________ Installation Date:_________________________________________
Place of Purchase: _________________________________________________ Model Number: __________________________________________