Air Lift OFF65991 User manual

Quick Reference Guide
Power ON the Desk:
When you plug in the desk, you
will hear a beep. The controller
will then show the current height
of the desk. If the number
indicated on the display is
different from the actual height,
you will need to reset it.
How to Reset
Press and hold the button until you hear a "beep-beep" sound
button again until it shows a number and
If the display shows “rst”, press and hold the
you hear a "beep-beep" sound.
How to Adjust the Height
Press and HOLD either the or to adjust to your desired height of the desk.
and
How to Lock/Unlock the Controller
First adjust the desk height to your desired lock height. Then press and HOLD the
buttons together for about 5 seconds until “Loc” is displayed.
At this moment, the Controller is locked and the desk height can’t be adjusted.
buttons together for about 5 seconds until a In order to unlock, press and HOLD the and
number (previously locked height) is displayed.
Power Save Mode
If there is no action for 1 minute, the desk will enter the power-saving mode. The display on the
Controller will be turned off. Press any button on the Controller to wake the desk from “Power
Save Mode”.
How to Save the Height in Memory
There are 3 available memory heights you can save - 1, 2 & 3. Adjust the desk to your desired
height and press the “M” button to display “S-“. Then press any of one the 1, 2 or 3 number
button. When a memory is saved, you will hear “beep-beep” sound.
By repeating the same steps, you can save or override an old saved memory with a new height.
Please see reversed side for the complete list of error codes and troubleshooting steps
for this desk.
airLIFT Electric Tempered Glass Height Adjustable Desk
(Model No. OFF65991, OFF65992)
MEMORY
1/2/3
SAVE
MEMORY
LED
DISPLAY
UP/DOWN
ARROW

SC0
SC1
SC2
SC3
R-2
R-3
HOT
R-5
Error Code List
Code
Action
Self-Check Fail - Standby Mode Error
Self-Check Fail - Main Power Error
Self-Check Fail - Save Memory Error
Self-Check Fail - Sensor Error
Table Tilt Alert
Re-plug in the power cable. If the alert does not clear,
please contact customer service.
Re-plug in the power cable. If the alert does not clear,
please contact customer service.
Re-plug in the power cable. If the alert does not clear,
please contact customer service.
Re-plug in the power cable. If the alert does not clear,
please contact customer service.
The desk will run in the opposite direction for about 2"
automatically, then the alert will clear.
Sync Failure
Overheat Protection
Control system
malfunction
button until you
Reset the desk, please and hold the
hear a "beep-beep" sound.
Let the motors cool down for 18 minutes.
Check the connection of the power cable and LED control panel.
R-6
RST
E10
E11
E12
E13
E14
E15
E16
E17
Voltage irregularity
Not reset completely
Driver Short-Circuit
Re-plug in the power supply. If the alert does not clear,
contact customer service.
Remove some weight from the desk, then the alert will clear
after 20 seconds.
Check the connection of motor cable
Please contact customer service.
Over-Load Protection
Motor Phase Failure
Moving Direction Error
Contact customer service.
The desk will run in the opposite direction for about 2"
automatically, then the alert will clear.
Contact customer service.
Contact customer service.
Motor wire not connected
Mechanical Malfunction
Anti-collision
Motor Stalling Alarm
Meaning
airLIFT Electric Tempered Glass Height Adjustable Desk
(Model No. OFF65991, OFF65992)
*NOTE: We recommend using TWO people to assemble the desk.
Check the connection between motor cable and
the LED control panel
Get help with assembly and report damaged or missing parts.
Email:
[email protected]
Telephone:
1 [phone]
Hours (M-F): 8:30 AM - 4:30 PM (PST)
button until you
Reset the desk, please and hold the
hear a "beep-beep" sound.