LOOSE-FILL MATERIALS
• Maintain a minimum depth of 9 in. of loose-ll materials such as wood mulch/
chips, engineered wood ber (EWF), or shredded/recycled rubber mulch for
equipment up to 96 in. high; and 9 in. of sand or pea gravel for equipment up to 60
in. high. NOTE: An inial ll level of 12 in. will compress to about a 9 in. depth of
surfacing over me. The surfacing will also compact, displace, and sele, and should
be periodically relled to maintain at least a 9 in. depth.
• Use a minimum of 6 in. of protecve surfacing for play equipment less than 48 in. in
height. If maintained properly, this should be adequate. (At depths less than 6 in.,
the protecve material is too easily displaced or compacted.)
• Use containment, such as digging out around the perimeter and/or lining the perim-
eter with landscape edging. Don’t forget to account for water drainage.
• Check and maintain the depth of the loose-ll surfacing material. To maintain the
right amount of loose-ll materials, mark the correct level on play equipment support posts. That way you can easily see when to replenish and/
or redistribute the surfacing.
• Do not install loose ll surfacing over hard surfaces such as concrete or asphalt.
POURED-IN-PLACE SURFACES OR PRE-MANUFACTURED RUBBER TILES: You may be interested in using surfacing other than loose-ll materials– like
rubber les or poured-in-place surfaces.
• Installaons of these surfaces generally require a professional and are not “do-it-yourself” projects.
• Review surface specicaons before purchasing this type of surfacing. Ask the installer/ manufacturer for a report showing that the product has
been tested to the following safety standard: ASTM F1292 Standard Specicaon for Impact Aenuaon of Surfacing Materials within the Use
Zone of Playground Equipment. This report should show the specic height for which the surface is intended to protect against serious head
injury. This height should be equal to or greater than the fall height-vercal distance between a designated play surface (elevated surface for
standing, sing, or climbing) and the protecve surfacing below-of your play equipment.
• Check the protecve surfacing frequently for wear.
PLACEMENT: Proper placement and maintenance of protecve surfacing is essenal. Be sure to:
• Extend surfacing at least 72 in. from the equipment in all direcons.
• For to-and-fro swings, extend protecve surfacing in front of and behind the swing to a distance equal to twice the height of the top bar from
which the swing is suspended.
• For re swings, extend surfacing in a circle whose radius is equal to the height of the suspending chain or rope, plus 6 feet in all direcons.
maintenance instructions
At the BEGINNING of each play season:
• Check all moving parts including swing seats, ropes, cables, and chains for wear, rust, or other deterioraon. Replace as needed;
• Check metal parts for rust. If found, sand and repaint using a non-lead-based paint meeng the requirements of 16 CFR 1303;
• Reinstall any plasc parts, such as swing seats or any other items that were removed for the cold season;
• Rake and check depth of loose ll protecve surfacing materials to prevent compacon and to maintain appropriate depth. Replace as necessary.
TWICE A MONTH DURING play season:
• Rake and check depth of loose ll protecve surfacing materials to prevent compacon and to maintain appropriate depth. Replace as necessary.
ONCE A MONTH DURING play season:
• Check all moving parts including swing seats, ropes, cables, and chains for wear, rust, or other deterioraon. Replace as needed.
At the END of each play season or when the temperature drops below 32°F:
• Remove plasc swing seats and other items as specied by the manufacturer and take indoors or do not use;
• Rake and check depth of loose ll protecve surfacing materials to prevent compacon and to maintain appropriate depth. Replace as necessary;
• Owners shall be responsible for maintaining the legibility of the warning labels.
When you are ready to dispose of swing, make sure that all swing components are disposed of in accordance with local waste ordinances. The seat of this swing
can be recycled. Remaining parts should be disassembled and disposed of in such a way that no unreasonable hazards exist at me the swing is discarded.
WARNING: Failure to carry out these checks and inspecons could result in fall or injury.
SAFETY INFORMATION
To reduce the likelihood of injury please follow the guidelines as outlined in these instrucons. You can visit our website www.mandmsalesinc.om to review
the instrucon manual in the future or keep this instrucon sheet for reference: Air Riderz® MM00151.
The installaon instrucons above are reecve of the U.S. Consumer Product Safety Commission’s Outdoor Playground Safety Handbook. For a complete
descripon of installaon instrucons and warnings for outdoor playground equipment you can visit our website www.mandmsalesinc.com to link to the
current CPSC handbook and review in its enrety.
Our products are tested to ensure safety and compliance with Consumer Product Safety Improvement Act of 2008 (CPSIA) including specicaons for lead
paint and phthalates and ASTM Internaonal F1148 Standard Consumer Safety Performance Specicaons.
M&M Sales Enterprises, Inc.
1300 Synergy Court, Dubuque, IA 52002 | 877-242-0154 www.mandmsalesinc.com
