AIREDALE Artus User manual

Installation



(BLUE) 


(GREY) (PINK)(RED) 

A
285mm
minimum
203mm
CW INLET
HW OUTLET
CONDENSATE DRAIN
(6mm ID HOSE)
CW OUTLET
HW INLET
15mm COMPRESSION (X4)




200mm
SENSOR-B2
X3
X2 X6
1-2
KNX
1-2-3
BACNETMSTP
1X2.1& X2.2
BACnet/ IP
2
X1
230V50Hz
NPEL


 



Item Description
230V/1PH/50Hz Mains Incoming Connector
Return Air Temperature Sensor
BACnet MSTP Connection (optional)
KNX Display Connection to Room Operator Unit
BACnet IP 2 Port RJ45 (optional)
On/Off switch (green illuminated switch)
6A Unit Mains Fuse
No Unit Connection Adapter Customer Termination
15mm Compression 15mm to 1/2” 1/2” Hose Connection
15mm Compression N/A 15mm PEX Tube Connection
15mm Compression N/A 15mm Copper Pipe Connection
Bypass Leg Option N/A N/A
Return Air Sensor
Sensor Mounting
Bracket
No Qty Description
1Artus Chassis and Fascia tted
3 Filters (2 short, 1 long)
1Return Air Sensor
1 Return Air Sensor Bracket
6 Return Air Sensor Clips
1Electrical Connection Tool
1 Cooling Commisioning Plug (Blue)
1 Heating Commissioning Plug (Red)
1 Mains Cable Plug
1 Return Air Sensor Plug (Grey)
1 KNX Cable Plug (Pink)
AR- E
L

X1
PE

Mains Incoming 230V / 1Ph + N / 50Hz/60Hz
N

X3
1

Return Air Temperature Sensor
2

To Unit (Supplied Loose)
X6
1

+
KNX / PL-Link Bus Communication Connection
2

-
Room Operator Unit (Optional, Supplied Loose)
X2
1


Ethernet
RJ45
BACnet/IP 2 Port Ethernet Switch
2


Note: Shielded Cat 5e cable is recommended for Ethernet connections.
KNX
RJ45
Room Sensor Wall Mounted Display
BMS / Scheduler / Third Party
NTC NTC NTC NTC
Unpacking and Parts
Wiring 
Temperature Sensor

Opening the Unit

Mounting and Levelling

Condensate Drain

Water Pipework

IMPORTANT - READ ME
Artus Installation and Commissioning Guide
±2mm
ARTUS_9456351_A3Guide_V1.0.0_08_2018
(tted by others)
1/50 - 1/100
4mm

Commissioning
Unlock Select Lock
The PICV valve should be setup to the design owrate of the unit. Please see table below.
PICV Valve Commissioning

Pressetting
%
Max
Flowrate
l/h
Flowrate
l/s
100 780 0.217
90 702 0.195
80 624 0.173
70 546 0.152
60 468 0.130
50 390 0.108
40 312 0.087
30 234 0.065
20 156 0.043
10 78 0.022
Step 1
Remove Velcro lined insulation 
around the Pressure Independent
Control Valve to access binder
points .
Step 2
Using the binder points , measure the
differential pressure across the valve .
If the measured differential pressure is
higher than the start-up pressure (>20kPa),
the valve is keeping the ow stable at the
preset value.
Item Description
Lined Insulation with Velcro xings
Pressure Independent Control Valve (PICV)
Binder Insertion Points
Pressure Gauge (supplied by others)




PICV Binder Points
Commissioning Plug
Return Air Sensor Socket
Red Plug - Heating Mode
Blue Plug - Cooling Mode
Heating Mode (valves energised)Cooling Mode (valves de-energised)
Commissioning Mode

Thermic Valve Positions

Always use the electrical connection tool when inserting/removing temperature sensors
and commissioning plugs to reduce the risk of damage to the retaining clip.
The commissioning plugs are used to force actuator operation.
Push Push
Filter Installation / Removal

Network Setup

Air Bleed
Bleeding the Coil

Airedale International Air Conditioning Ltd. Leeds Road, Rawdon, Leeds, LS19 6JY.
Tel: [phone] Fax:[phone] E-mail: [email protected] Web: www.airedale.com
Airedale do not offer any commissioning services for the Artus. Mechanical commissioning, including
water side balancing, must be completed by others before Airedale or other third party Siemens Solution
Partners congure the Artus(s) for master/slave operation, room operator units, BMS integration etc.
The serial number shown on the barcode on the inside of the lid must be recorded along with installed
location prior to arranging network setup.
Push
Required for water balancing.
Note: Power must be ON.