AiRide G2 User manual


BLUETOOTH INTERCOM
Operaon Manual
Attention：
Thank you for purchasing G2 helmet Bluetooth intercom . For
best use experiences , please read manual before use .

1
3
4
2
Installaon
Headphone & Mic Kits
Clip
Fix the headphone & Mick Kits on the
right position, adjust the speakerand
mic, then hide the speaker cable.
Insert the main unit, press to the
buttom of kits, main unit locked and
installation completed.
Take away the main unit by press the
button and slide it up, disassmble
compeleted.
Remark: Mic should be close enougn
to moutg, and speaker near to ear.
plase use sponge if the speaker
postion is too deep.
Press
01
5
Press Slide up

Operaon
1
1
2
3
4
5
6
7
8
9
2 3 4 5 6
7 8 9
Intercom
Volume - / Previous
Volume + / Next
LED Indicator
Function
Charge / Data
Headphone & Mic Kits
Passersby Communication
Aux In
1.Outlook / Function
02

2. Charge
2.1 How to Charge
Charge / Data Port
For rst time use , please recharge the device until the red light is o .
1. Connect the cable with device and PC USB port ;
2. After cable connected , the red light on and start to charge , when
battery is full , the red light will be o automatically . (Need 2 hours to
fulll the battery ) .
* Do not use power from car or motorcycle directly , unstable power may
damage the device .
03

2.2 Power Detect & Notication Function
Low Power Notication:When power lower than 10% , red light ash in
the function button and voice message will remind power lower than
10% , please recharge immediately .
Power Detect Function:G2 has power detect function , when device is
on , short press volume - and volume + button at the same time ,
recorded voice message will tell you :
Power over 90%
Power over 50%
Power lower 50%
Power lower 10% please recharge immediately
04

3. Switch On / OFF
3.1 Switch On
3.2 Switch O
3 Seconds
3 Seconds
Press Intercom + Function button for 3 seconds until the LED indicator
ash blue light , a voice prompt “Welcome” will be heard .
When device is on , press Press Intercom + Function button for 3
seconds until the LED indicator ash red light , a voice prompt “Power
O” will be heard .
05

1.
4. Cellphone Funcon
4.1 Pair with Cellphone
STEP
2.
STEP
About 5 sec
When device is on , long press function button, red and blue light ash
in the function button , entering pairing mode .
Switch cellphone Bluetooth , choose G2, the pairing is complete . Voice
message will also say pairing complete .
Remark: when pairing complete , please check both cellphone audio
and media audio are all chosen , otherwise call or music can not be
processed .
G2
Name
06

4.2 Cellphone Function
Answering Call: Short press function once .
Hangup Call: After call , short press function once .
Refuse Call: Long press function button for 2 seconds .
Redial: Short press function button twice .
Volume Up: Press Volume + while talking .
Volume Down: Press Volume - while talking .
Manual/Auto Switch: Long press Function , Volume+ and Volume- at
the same time for 3S when Stand by .
07

5. Voice Command
When your G2 is paired up with cellphone , long press Passersby
Communication button , will automatically switch on the voice command
function .
*Cellphone must equipped with this function .
08

6. Music Play
Play: When device is on , short press Function .
Pause: When music is playing , short press Function .
Volume Up : When music playing ,short press volume + once .
Volume Down : When music playing ,short press volume - once .
Play Previous: When music playing ,long press volume - for 2 seconds .
Play Next: When music playing ,long press volume + for 2 seconds .
Volume + / Next
Volume - / Previous
2
3
09

7. Wire Connecon
Any device with 3.5mm connector can transmit voice signal to G2.
through the transfer line.
Two-Way Radio
(Needs professional radio connect cable)
10

8. Passersby Communicaon
Short Press Passersby communication button to switch on this function ,
and re-press will switch o this function .
*This function allows rider talk to passersby without take o helmet .
Passersby Communication
11

9. Intercom Funcon ( Rider to Rider )
When device on , press both Headset A and B’s function button until
red and blue light to enter pairing mode .
Short press Headset A or B’s intercom button , the red and blue light
will be ashed slowly . once LED indicator turns into blue , the device
connection completed .
After connection completed , you can switch on the intercom
function by press any of the headset’s intercom button .
Headset A Headset B
Cellphone A Cellphone B
1.
2.
3.
12

10.FM
FM Switch On: Press Intercom button for 3 seconds when device is
stand by ;
FM Switch O: Press Intercom button for 3 seconds when FM is on ;
Volume Up : When FM On , short press volume + once .
Volume Down : When FM On , short press volume - once .
Search Previous: When FM On , long press volume - for 2 seconds .
Search Next : When FM On , long press volume + for 2 seconds .
Volume + / Next
Volume - / Previous
Intercom
1
2
3
13

11. Memory Clean
Memory Clear:When device is on , press Volume + and function button
at the same time for 3 seconds . Then G2 will clear the pairing memory
with other devices .
14

12. Q&A
12.1 Q&A
12.2 Warning
No sounds from one or two side speaker
Check device plug , needs to rmly connected
Can it be recharged from bike USB charger while riding ?
Not recommended , unstable power source will cause damage on
internal circuit , may cause unable to recharge/can’t fully
charged/can’t switch on.
Power bank will be good .
When using radio , not transmission or continuous transmission
Check 2.5mm pin , has to insert rmly . The pin equipped with
waterproof aprons , user might think its already plugged .
New device can’t switch on
Recharged at least 30 minutes before switch use .
12.21 Sound Volume Warning
Long period or too loud may hurt hearing ability .
12.22 Disassemble or Modication
The G2 is precisely made in factory . Any disassemble or modication
may damage the device , please do not tear any of the safety regulation
and serial sticker from the device , that will void the warranty . Please
contact us directly if needed .
Q1:
A1:
Q2:
A2.1:
A2.2:
Q3:
A3:
Q4:
A4:
15

FCC Statement
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
To assure continued compliance, any changes or modifications not expressly
approved by the party.
Responsible for compliance could void the user’s authority to operate this
equipment. (Example- use only shielded interface cables when connecting to
computer or peripheral devices).
This equipment complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that
may cause undesired operation.
RF warning statement:
The device has been evaluated to meet general RF exposure requirement.
The device can be used in portable exposure condition without restriction.