AirLive POE-200CAM V2 User manual

AirLiveWL‐2000CAMUser’sManual
0







































POE-200CAM v2
1/4 CMOS Dual Stream
DOME IP Camera
User’s Manual


AirLivePOE‐200CAMv2User’sManual
1
Before You Use this Product
This product has been designed with safety in mind. However, if not used properly, electrical products can cause
fires which may lead to serious bodily injury. To avoid such accidents, be sure to heed the following:
Legal Caution
Video and audio surveillance can be forbidden by laws that vary from country to country. Check the laws in your
local region before using this product for surveillance purposes.
Heed the safety precautions
Be sure to follow the general safety precautions and the “Operation Notice.”
In case of a breakdown
In case of system breakdown, discontinue usage and contact your authorized dealer.
In case of abnormal operation
• If the unit emits smoke or an unusual smell,
• If water or other foreign objects enter the cabinet, or
• If you drop the unit or damage the cabinet:
1 Disconnect the cable and the connecting cables.
2 Contact your authorized dealer or the store where you purchased the product.
Operation Notice - Operating or storage location
Avoid operating or storing the camera in the following locations:
• Extremely hot or cold places (operating temperature: 0 °C to +50 °C [32 °F to 122°F])
• Exposed to direct sunlight for a long time or close to heating equipment (e.g., near heaters)
• Close to sources of strong magnetism
• Close to sources of powerful electromagnetic radiation, such as radios or TV transmitters
• Locations subject to strong vibration or shock
Ventilation
To prevent heat buildup, do not block air circulation around the device.
Transportation
When transporting the camera, repack it as originally packed at the factory or in materials of equal quality.
Cleaning
• Use a soft, dry cloth to clean the external surfaces of the device. Stubborn stains can be removed using a soft
cloth dampened with a small quantity of detergent solution, then wipe dry.
• Do not use volatile solvents such as alcohol, benzene or thinners as they may damage the surface.


AirLivePOE‐200CAMv2User’sManual
2
Table of Content
Table of Content ................................................................................................................................................................2
Chapter 1 Installation ............................................................................................................ 4
1.1 Installation Steps .................................................................................................................................................4
1.2 Package Contents...............................................................................................................................................5
1.3 Overviews.............................................................................................................................................................6
Chapter 2 Using IP Camera via Mobile Phone..................................................................... 7
2.1 3G Mobile Phone Viewing .................................................................................................................................7
2.2 2.5G Mobile Phone Viewing ..............................................................................................................................7
Chapter 3 Using IP Camera via Web Browser ..................................................................... 8
Chapter 4 Initial accessing the IP camera ........................................................................... 9
Chapter 5 How to Use.......................................................................................................... 10
5.1 Accessing the IP Camera ................................................................................................................................10
5.2 Configuration of Main Menu ............................................................................................................................11
Chapter 6 Setting................................................................................................................. 13
6.1 Basic ...................................................................................................................................................................13
6.2 Advance..............................................................................................................................................................27
Chapter 7 CamPro Express User’s Manual ....................................................................... 40
7.1 Getting Started...................................................................................................................................................40
7.2 Running the Installation Wizard ......................................................................................................................42
7.3 Start Service Program ......................................................................................................................................46
7.4 Admin Program..................................................................................................................................................47
7.5 Monitor Program................................................................................................................................................78
7.6 Web Monitor.......................................................................................................................................................87
7.7 Multi Playback....................................................................................................................................................89


AirLivePOE‐200CAMv2User’sManual
3
APPENDIX A. IIS Installation for Windows Vista .....................................................................................................96
APPENDIX b. Security Setting in Web Monitor under Vista ..................................................................................99
APPENDIX C. Frame Rate & Bit Rate Table..........................................................................................................101
APPENDIX D. Storage Requirement Table ............................................................................................................103
Chapter 8 Technical Specifications.................................................................................. 104
Chapter 9 Glossary............................................................................................................ 105


AirLivePOE‐200CAMv2User’sManual
4
Chapter 1 Installation
1.1 Installation Steps
Follow these steps to install the POE-200CAMV2 on your Ethernet:
1. Check the package contents against the list below.
2. Set the device. See IP Installer User Manual on the available methods.
1. Install Ethernet Cable2. Install Speaker
3. Put on ceiling


AirLivePOE‐200CAMv2User’sManual
5
1.2 Package Contents
Camera POE-200CAMv2 Dome IP Camera
Quick Installation Guide Brief product information and quick installation
Software CD
IP Surveillance Software
Intelligent IP Installer
User Manuals
Language Packs
Screw Pack Two screws and plastic wall anchors
Adaptor 12V DC, max 6W
Camera POE-200CAMv2 Dome IP Camera








IP Camera Power Adapter, DC12V, 1.25A
Installation CD Quick Setup Guide


AirLivePOE‐200CAMv2User’sManual
6


1.3 Overviews
Front & Side:












DI / DO Terminal connector diagram
Please refer the following illustration below for connection method.
NOCOMD‐  D+












Note
Hold the Reset Button for 10 seconds to restore the camera to default
Ground
Ground
12V
Alarmoutdevice
12V
Max.30W
Switch


AirLivePOE‐200CAMv2User’sManual
7
Chapter 2 Using IP Camera via Mobile Phone
To use IP cameras via mobile phones, please make sure your RTSP is set to “ON”. (Default is “ON”) To
change the settings of IP cameras, please see “Settings” for details.
2.1 3G Mobile Phone Viewing
For 3G mobile phone viewing, type “rtsp://<IP>:<PORT>/video.3gp” into your 3G web browser. <IP> is the IP
address of your IP camera, <PORT> is the RTSP port of your IP camera (Default value is 8554.)
Example: rtsp://100.10.10.1:8554/video.3gp
Note:
• You can also use RTSP clients (RealPlayer, MPlayer, Windows Media Player, QuickTime…etc.) to view RTSP
streaming, just type in “rtsp://<IP>:<PORT>/video.3gp” as the Player’s URL.
2.2 2.5G Mobile Phone Viewing
For 2.5G mobile phone viewing, type “<IP>/mobile.wml” into your 2.5G web browser. <IP> is the IP address of
your IP camera.


















AirLivePOE‐200CAMv2User’sManual
8


Chapter 3 Using IP Camera via Web Browser
System Requirement
To use the product normally, we strongly recommend your computer follows our minimum system
requirement (Computer level lower than this might cause some problems.)
Item Requirements
CPU Pentium 4 1600MHz (or equivalent AMD)
Graphic Card 64MB RAM graphic cards (or equivalent on-board graphic cards)
RAM 512MB
Operating System Windows 98, ME (Please see Note)
Windows 2000, 2003, XP, Vista
Web Browser Internet Explorer 6 or later
Note:
• If you’re using Windows 98 or ME, please install IP Installer before using WEB UI to ensure the system runs
normally.
•If you can’t view the recorded video file (missing video decoder), please install Xvid codec while installing
Intelligent IP Installer. (For Windows 98, ME or 2000 server, the codec might not work properly. You’ll need to
download Xvid codec 1.0 from the internet.


AirLivePOE‐200CAMv2User’sManual
9
Chapter 4 Initial accessing the IP camera
1. Start your web browser, and enter the IP address or host name of the AIRLIVE IP camera in the Location /
Address field of your browser.
Note：
• If you only want to view the video without setting page, enter “http://<IP>/index2.htm”as your web URL.
2. Use the default account “admin” and default password “airlive”.
Note：
• The default user name “admin” and the password are set at the factory for the administrator. You can
change them in the Account Menu under Setting.

3. The monitor image will be displayed in your browser.


AirLivePOE‐200CAMv2User’sManual
10
Chapter 5 How to Use
This chapter introduces how to monitor the image from the device using Microsoft web browser. The IP
camera can be used with Microsoft web browsers and Intelligent IP Installer in Windows operation systems. This
document focuses on introducing you to Microsoft web browser. The recommended browser for Windows is
Internet Explorer 6.0. If you want to know how to use IP camera with Intelligent IP Installer, check Intelligent IP
Installer User’s Manual in Windows operation systems.
The functions of the device should be set by the Administrator. For further instructions on setting the device, see
“Setting the Camera.”

5.1 Accessing the IP Camera
1.Start your web browser, and enter the IP address or host name of the IP camera in the Location / Address field of
your browser.
Note：
• If you only want to view the video without setting page, enter “http://<IP>/index2.htm”as your web URL.
2. Use the default account “admin” and default password “airlive”.
Note：
• The default user name “admin” and the password are set at the factory for the administrator. You can change
them in the Account Menu under Setting on page 25.
3. The monitor image will be displayed in your browser.


AirLivePOE‐200CAMv2User’sManual
11
5.2 Configuration of Main Menu
5.2.1 Setting

This function is only for the Administrator. Click this button to get into the Basic and Advance settings menu.
5.2.2 Client Setting
Mode: Click on the pull-down box to choose between MPEG4 and MJPEG video compression mode.
Note：MJPEG streaming is unavailable if RTSP mode is ON.
View Size: Select the desired display image resolution to 640X480 or 320X240.
Protocol: Select the transferring protocol from TCP, UDP, HTTP and Multicast.
Video Buffer: Turn the Video Buffer function On/Off. The Video Buffer function makes the streaming more
smoothly in unsteady network environment, but might cause a little delay in live viewing.
5.2.3 Image Setup
You can use the tool bar to optimize video brightness, contrast, and saturation.


AirLivePOE‐200CAMv2User’sManual
12
5.2.4 Live View
Snapshot:
You can capture a still image shot by the camera and save it in your computer.
1. Press and a snapshot window will appear.
2. Click “Save” to save the picture in your computer.
3. Click “Close” to return to the view page.
Zoom in/out the image via the monitor window.
1. Click to display the digital zoom in window.
2. Pull the to adjust the digital zoom range, and it will be shown
on the above window.
3. You can use the left click of your mouse to move the to any where on the window.
Audio buttons：
：Speakersturnedon. ：Speakers turned off.
：Microphone turned on. ：Microphone turned off.
•：Volume control bar.
Note：
It means the speakers of your computer are turned on to transmit the sounds from the connected IP
camera(s). Similarly, means you can broadcast to the connected IP camera(s) via the Ethernet using your
microphone.
Video play buttons:
：Pause the current video ：Play the video.
：Stop the current video. ：Record the current video.


AirLivePOE‐200CAMv2User’sManual
13
Chapter 6 Setting
6.1 Basic
Click on the “Basic” folder to display the sub folders, including System, Camera, Network, and Security.
6.1.1 System
Information
The Information page provides you with product factory information, including Product name, Firmware
version, and Web version.
Day & Time


AirLivePOE‐200CAMv2User’sManual
14
Current date & time：This displays the current date and time of the device.
PC clock：This displays the date and time of the monitoring PC clock.
Date & time format：Click the pull-down box to select among different time display formats, including
yyyy-mm-dd hh:mm:ss (year-month-day hour:minute:second), mm-dd-yyyy hh:mm:ss (month-day-year
hour:minute:second), and dd-mm-yyyy hh:mm:ss (day-month-year hour:minute:second).
Adjust：Select one of four time adjusting modes.
Keep current setting：Select this mode to keep the current date and time of the device.
Synchronize with PC：Select this mode to make the date and time of the device the same as the monitoring
PC.
Manual setting：Select this mode to manually adjust the date & time of the device.
Synchronize with NTP：Specify the NTP server name and the Refresh Interval to synchronize the date and
time of the device with those of the time server, known as the NTP (Network Time Protocol) server.
Note:
• The NTP server (Network Time Protocol) is the time server which is an Internet standard protocol (built
on top of TCP/IP) that assures accurate synchronization to the millisecond of computer clock times in a
network of computers.
NTP server name：Type the host name or IP address of the NTP server, up to 64 characters.
Time zone：Select the time zone and time difference from Greenwich Mean Time in the area where the device is
installed from the pull-down box.
Initialize
Reboot：Click this button to reboot the device. A confirmation dialogue will appear. Click OK to proceed. It takes
about two minutes to reboot the device.
Factory default：Click this button to reset the device to the factory default settings. A confirmation dialogue will


AirLivePOE‐200CAMv2User’sManual
15
appear. Click OK to proceed;the network indicator on the device will start to blink. After completing adjustments
to the default settings, the device will reboot automatically. Do not turn off the device until the device reboots.
Backup setting data：Save the setting data of the device to a file. Click Save, and follow the instructions on the
browser to save the setting data file to your specified location.
Restore setting：Load the saved setting data of the device. Click Browse and select the file in which the setting
data is stored. Click OK, and the device is adjusted according to the loaded data and restarted.
Firmware update：Upgrade the device software. Click Browse and select the file for upgrading. A confirmation
dialogue will appear. Click OK to start upgrading. The device will reboot upon completion.
Note:
• Use only upgraded files that are special for this device. Problems may occur otherwise.
• Do not turn off the device power or disconnect the network until the upgrading is completed.
Upload language pack：Upgrade the device language pack. Click Browse and select the file for upgrading. A
confirmation dialogue will appear. Click OK to start upgrading. The upgrade is applied immediately. The default
language is “English.”
6.1.2 Camera
6.1.3 General
RTSP: Switch the RTSP streaming On/Off.
Note：
• RTSP: Real Time Streaming Protocol. RTSP is supported by most of the media clients. (RealPlayer,
Media Player, QuickTime, etc…)
Image Rotate：Enables user to mirror or flip the display screen.
Night Mode：Turn Night Mode ON/OFF.
Lighting：Choose the lighting environment among 50Hz, 60Hz and Outdoor.
White Balance：Choose the White Balance to Auto, Fluorescent, Incandescent and Black&White.


AirLivePOE‐200CAMv2User’sManual
16
Overlay：Select to add Text Overlay or Privacy Mask on/off the display screen.
Tex t O ve r la y：Enables users to see some information on the display screen, including Date/Time and
user-defined text. You can also change the background color.
Privacy Mask：Enables users to conceal an area of the video image.
6.1.2.2 MPEG4
Computer View
RTSP (If RTSP mode is ON)
RTSP port: Specify the transmission port number of RTSP streaming video. Default value is 554.
Viewer authentication: If the viewer authentication is ON, users viewing through RTSP will be requested to
key-in username and password.
RTP (If RTSP mode is ON)
Unicast streaming:
Unicast streaming Video/Audio port range: Specify the transmission port range of RTP streaming video. RTP
will select a port randomly from the range.
Multicast streaming:
Multicast address: Specify the multicast server address.
Video / Audio Port: Specify the transmission port number of the video data. Specify an even number from 1024
to 65534.
Time-To-Live: Set the maximum TTL that multicast can pass through.


AirLivePOE‐200CAMv2User’sManual
17
MPEG4 viewer port (If RTSP mode is OFF)
Unicast streaming Video/Audio port number: Specify the transmission port number of the video data. It is
initially set to 8090. Specify an even number from 1024 to 65534.
Image Size：Specify the image size the network camera transmits. You can choose among 704 × 480, 352 ×
240 and 176 × 120 for NTSC mode and 704 × 576, 352 × 288 and 176 × 144 for PAL mode.
Frame rate：Set the frame rate of the MPEG4 image. Selectable values are 5, 10, 15, 20, 25, 30 fps. The unit
“fps” stands for “frames sent per second”.
Quality
Auto：The quality and bit rate will be automatically decided according to the frame rate.
Fixed Quality：The selectable values are Medium, Standard, Good, Detailed and Excellent.
Fixed Bit rate：Set the bit rate of MPEG4 image transmission for a line. Selectable values are 64, 128, 256, 384,
512, 768, 1024, 1280, 1536 and 2048 kbps.
Note：
• The selected frame rate and bit rate are a tentative value. The actual frame rate and bit rate may be different
according to the image size, the shooting scene or the network condition.


AirLivePOE‐200CAMv2User’sManual
18


MobileView
RTSP (If RTSP mode is ON)
RTSP port: Specify the transmission port number of RTSP streaming video. Default value is 8554.
RTP (If RTSP mode is ON)
Unicast streaming:
Unicast streaming Video/Audio port range: Specify the transmission port range of RTP streaming video. RTP
will select a port randomly from the range.
Multicast streaming:
Multicast address: Specify the multicast server address.
Video / Audio Port: Specify the transmission port number of the video data. It is initially set to 10000 and 11000.
Specify an even number from 1024 to 65534.
Time-To-Live: Set the maximum TTL that multicast can pass through.
Image Size: The Image size of Mobile view is fixed at 176x120.
Frame rate：Set the frame rate of the MPEG4 image. Selectable values are 5, 10, 15, 20 fps. The unit “fps”
stands for “frames sent per second”.
Quality
Fixed Bit rate：Set the bit rate of MPEG4 image transmission for a line. Selectable values are 64, 32, and
16kbps.



AirLivePOE‐200CAMv2User’sManual
19
6.1.2.3 MJPEG
Note：
• MJPEG settings are unavailable if the RTSP mode is ON, which means the MJPEG streaming is closed.
MJPEG viewer port
Unicast streaming Video/Audio port number:Specify the transmission port number of the video data. It is
initially set to 8070. Specify an even number from 1024 to 65534.
Note：
• Unicast streaming：Specify the transmission port number of the video data and audio data used when
UDP (Unicast) is selected with the TCP/UDP transmission switching icon in the main viewer.
Image Size：Specify the image size the network camera transmits. You can choose among 704 × 480, 352 ×
240 and 176 × 120 for NTSC mode and 704 × 576, 352 × 288 and 176 × 144 for PAL mode.
Frame rate：Set the frame rate of the MJPEG image. Selectable values are 5, 10, 15 fps. The unit “fps” stands
for “frames sent per second”.
Quality
Auto：The quality will be automatically decided.
Fixed quality：The selectable values are Medium, Standard, Good, Detailed and Excellent.