AirLive AirCam OD-600HD User manual

A
irCam OD-600HD
H.264 1.3 MegaPixel PTZ
Vandal Proof Dome
Use
r
’s Manual

Copyright and Disclaimer
Copyright & Disclaimer
No part of this publication may be reproduced in any form or by any means, whether
electronic, mechanical, photocopying, or recording without the written consent of OvisLink
Corp.
OvisLink Corp. has made the best effort to ensure the accuracy of the information in this
user’s guide. However, we are not liable for the inaccuracies or errors in this guide.
Please use with caution. All information is subject to change without notice
All Trademarks are properties of their respective holders.

Table of Contents
i
AirLive AirCam OD-600HD User’s Manual
Table of Contents
1. Overview .....................................................................................................1
1.1 Introduction ..........................................................................................1
1.2 Features...............................................................................................1
1.3 Minimum System Requirements ..........................................................2
2. Package Contents......................................................................................3
2.1 Connections.........................................................................................4
2.2 Mounting the Camera ..........................................................................6
3. Preparation .................................................................................................7
3.1 Search and Set up by IPWizard II........................................................7
3.2 Using UPnP of Windows® XP or Vista ..............................................10
3.3 Install the Device behind a NAT Router .............................................10
3.4 Access the device from the Internet Explorer for the first time...........11
4. Operating the Network Camera ..............................................................13
5. Administrating the Device.......................................................................19
5.1 System Setting...................................................................................19
5.1.1 Network.................................................................................................................... 20
5.1.2 Camera : Adjust Camera parameters........................................................................ 28
5.1.3 System : Configure and maintain system.................................................................32
5.1.4 Video: Configure profile ..........................................................................................36
5.1.5 Audio: Audio parameters ......................................................................................... 39
5.1.6 User : Manage user name, password and login privilege ........................................40
5.1.7 E-Mail : Setup E-Mail configuration .......................................................................40
5.1.8 Object Detection : Setup Object detection...............................................................42
5.1.9 Event Server : Setup FTP/TCP/HTTP/SAMBA server configuration..................... 43
5.1.10 Event Schedule: Configure the event schedule......................................................47
Appendix A : Alarm I/O Connector .........................................................51
Appendix B :Frequently Asked Questions ............................................53
Appendix C : PING IP Address................................................................57
Appendix D : Bandwidth Estimation ......................................................58
Appendix E : Specifications....................................................................59
Appendix F : Configure Port Forwarding Manually ..............................61
Appendix G : DDNS Application .............................................................64
Appendix H : Power Line Frequency......................................................71

Table of Contents
AirLive AirCam OD-600HD User’s Manual ii
Appendix I : 3GPP...................................................................................72
Appendix J :Enable UPnP of Windows XP............................................73

1. Overview
AirLive AirCam OD-600HD User’s Manual
1
1 1. Overview
This user’s guide explains how to operate this camera from a computer. User should read
this manual completely and carefully before you operate the device.
1.1 Introduction
This camera is an inexpensive and fully scalable surveillance device. Because the Network
Cameras can be plugged into your existing local area network (LAN), you will potentially
save thousands of dollars from unnecessary cabling.
The device is accessible via the LAN or Internet connection. Connect your device directly to
a local area network or xDSL modem, and with Microsoft® Internet Explorer you get instant,
on demand video streams. Within minutes you can set up the device to capture a video
sequence to a PC. The live video can be uploaded to a website for the world to see.
1.2 Features
Vandal proof enclosure
Wide and fast Pan range: 355 degree and 180 degree/sec
Wide and fast Tilt range: 100 degree and 120 degree/sec
Easy installation with setup wizard
UPnP device discovery and NAT router transversal for easy installation
Dynamic IP Service, DIPS®, to search your IP camera from Internet easily
H.264, MPEG4 and JPEG triple compression simultaneously
Mega-pixel resolution up to 1280x1024
Up to 11-profile encoder simultaneously
UDP / TCP / HTTP protocols selectable
Supports video/audio multi-casting
3GPP for 3G mobile remote application
Mega-pixel or VGA mode selectable
30 fps for VGA mode
15 fps for Mega-pixel mode
Digital zoom
External microphone
Audio line out

1. Overview
AirLive AirCam OD-600HD User’s Manual
2
Two-way audio
Intelligent motion detection up to 10 zones
Go to preset once motion triggered
Image transmission using an FTP or e-mail for event
DDNS and PPPoE
Multi-channel control software for surveillance application
On-line firmware upgrade
802.3af PoE support (wired model only)
1.3 Minimum System Requirements
Microsoft Internet Explorer 6.0 or later
Microsoft Media Player 11.0 or later (to playback recorded file)
VGA Monitor resolution 1280 x 1024 or higher
Pentium-4 2.0 GHz or higher
Memory Size: 512MB or more
Windows XP, Vista

2. Package Contents
AirLive AirCam OD-600HD User’s Manual
3
User can find the following items in the package as below:
Item Descriptions
1. This Unit is the main
element of the product.
2. Screws x 3
3. Power Adapter dedicates
12V DC electric power output to
Network Camera.
4. User’s Manual CD provides
installation software,
application program, important
information and instructions for
operating the Network Camera.
5. Quick Start Guide provides
important information and
instructions for installing this
device.
If any of the above items are missing, please contact your dealer immediately.
Note: Using a power supply with a different voltage than the one included with the Network
Camera will cause damage and void the warranty for this product.
2 2. Package Contents

2. Package Contents
AirLive AirCam OD-600HD User’s Manual
4
2.1 Connections
1. RJ45 LAN socket: Connect to PC or Hub/Switch.
For connections to 10Base-T Ethernet or 100Base-TX Fast Ethernet cabling. This Ethernet
port built N-Way protocol can detect or negotiate the transmission speed of the network
automatically. Please use Category 5 cable to connect the Network Camera to a 100Mbps
Fast Ethernet network switch or hub.
In the LAN socket, there are two LEDs embedded:
LAN LED (green color)
This LED will be flashing while network accessing via Ethernet.
Power & Wireless LED (orange color)
This LED is used to indicate whether DC power is on or not. In addition, this LED will be flashing while the
wireless accessing of the Camera.
2. RS-485: Connect to a local keyboard controller.
DI/ DO: Connect to sensor in and alarm out devices

2. Package Contents
AirLive AirCam OD-600HD User’s Manual
5
Cable for I/O connectors:
Name Cable Color Function
12VDC Brown/White DC 12V (50mA maximum)
GND Blue/White GND
NC Purple/White Do not connect
NC Gray Do not connect
DI Green/White Digital signal input
DO Orange/White Digital signal output
3. Factory Default Reset
This button is used to restore the all factory default settings. Sometimes restarting the
device will make the system back to a normal state. However, if the system still got
problems after restart, user can restore the factory default settings and install it again.
Restore the device:
(i) Press the button down continuously.
(ii) Hold the button at least 5s seconds and release it. Then the device has been
restored to default settings and reboot again.
Note: Restoring the factory default setting will lose the all previous settings included IP
address forever. User needs to run the IPWizard II program to search the device and
configure it to let the device work properly again.
4. DC-in Jack
The input power is 12VDC. Note that supply the power to the Network Camera with the
power adapter included in package.
5. MIC in (audio in)
Connect a microphone to the network camera.
6. Line out (audio out)
Connect a loud speaker to the network camera. This function is for voice alerting and
two-way audio.

2. Package Contents
AirLive AirCam OD-600HD User’s Manual
6
2.2 Mounting the Camera
Ceiling Mount
Fix the camera to ceiling with the three supplied screws.
Install the Camera in LAN
1. Plug an Ethernet cable into the Camera
Connect an Ethernet cable to the LAN socket and attach it into the network.
2. Connect the external power supply to Camera
Connect the attached power adapter to the DC power jack of the camera. Note: Use the power
adapter, 12VDC, included in the package and connect it to wall outlet for AC power.
Once you have installed the camera well and powered it on, the power LED (orange) will turn on later. The
power LED turned on, it means the system is booting up successfully. Furthermore, if you have a proper
network connection, and access to the camera, the LAN LED (green) will flash.

3. Preparation
AirLive AirCam OD-600HD User’s Manual
7
3.1 Search and Set up by IPWizard II
When you installed the Camera on a LAN environment, you have two easy ways to search
your Cameras by IPWizard II or UPnP™ discovery. Here is the way to execute IPWizard II
to discover Camera’s IP address and set up related parameter in a Camera.
Search
When launch the IPWizard II, a searching window will pop up. IPWizard II is starting to
search Network Cameras on the LAN. The existed devices will be listed as below.
3 3. Preparation

3. Preparation
AirLive AirCam OD-600HD User’s Manual
8
View
If IPWizard II finds network devices, View button will be available. Please select the device you
want to view and click the View button. Then you could see the video from camera directly.
Furthermore you could double click the left button of mouse to link to the network device by browser.
LAN
In case you want to change the IP related parameters of wired interface, please select the
device you want to configure and click the LAN button. Relative settings will be carried out
as below.
You could modify the relative settings of the selected device. Click “<<” button will quit the
LAN setting procedure and click “>>” button will move to next page as below.

3. Preparation
AirLive AirCam OD-600HD User’s Manual
9
In case, you do not want to change username and/or password, then just click “Submit”
button to perform your setting accordingly. Click “<<” button will go back to previous page.
If you like to change username and/or password of the device, just click the check button.
Then, the related fields will show up as below.
After keying in new username and password, click “Submit” button to perform your setting
accordingly. Click “<<” button will go back to previous page.
Wireless
This model does not support wireless function. Therefore, IPWizard II disables this function
automatically.

3. Preparation
AirLive AirCam OD-600HD User’s Manual
10
3.2 Using UPnP of Windows® XP or Vista
UPnP™ is short for Universal Plug and Play, which is a networking architecture that
provides compatibility among networking equipment, software, and peripherals. This device
is an UPnP enabled device. If the operating system, Windows XP or Vista, of your PC is
UPnP enabled, the Network Camera will be very easy to be found.
Please refer to Appendix J to enable UPnP settings only if your operating system of PC is
running Windows XP.
Note: Windows 2000 does not support UPnP feature.
To discover your device, go to your Desktop and click My Network Places.
Click the targeted Device. Then Internet Explorer will connect to this Network Camera
automatically.
3.3 Install the Device behind a NAT Router
Once installed, the device is accessible on your LAN. To access the device from the
Internet you must configure your broadband router to allow incoming data traffic to the
device. If the device is installed on the LAN with a router, then it may get a dynamic IP
address from the DHCP server. However, if the device wants to be accessed from the WAN,
its IP address needs to be setup as fixed IP, also the port forwarding or Virtual Server
function of router needs to be setup.
However, if your NAT router supports UPnP feature, it can be very easy to achieve NAT
traversal automatically. To do this, enable the NAT-traversal feature, which will attempt to
automatically configure the router to allow access to the camera.

3. Preparation
AirLive AirCam OD-600HD User’s Manual
11
Installing the device with an UPnP router on your network is an easy 3–step procedure:
(1) Enable UPnP option of your NAT router
(2) Enable UPnP NAT traversal option of the Network Camera
(3) Access your Network Camera by DIPS
(1)Enable UPnP option of your NAT router
To use UPnP IGD function (NAT traversal), you need to make sure the UPnP function is
enabled in your router. Most new home routers should support this function. Some of
routers are default enable and others are not. Please check user’s manual of your NAT
router for detail.
(2) Enable UPnP NAT traversal option of the Network Camera
Refer to Setting ÎNetwork ÎUPnP page for detail NAT traversal setting.
(3) Access your Network Camera by DIPS
Refer to Setting ÎSystem ÎSystem page for detail DIPS information.
3.4 Access the device from the Internet Explorer for the first time
1. Start the web browser on the computer and type the IP address of the Network Camera
you want to monitor as below:
The Login Window of the Camera is prompted:

3. Preparation
AirLive AirCam OD-600HD User’s Manual
12
2. Type in your login name and password under “USERNAME” and “PASSWORD”
textbox.
For the first time use (default value), input the
User Name: admin
Password: airlive
That’s, type in “admin” on the “USERNAME” as a default name and leave PASSWORD
textbox airlive. Click “OK” button to start the main menu.
3. According your browser’s security setting, the IE Web Page may prompt the “Security
Warning” window. If so, select “Yes” to install and run the ActiveX control into your PC.
Otherwise, the system will load the ActiveX silently.
4. After the ActiveX control was installed and ran, the first image will be displayed.
Logging in as an User
If you log in the Camera as an ordinary User, “Setting” function will be not accessible.
Logging in as an Administrator
If you log in the Network Camera as the Administrator, you can perform all the settings
provided within the device.

4. Operating the Network Camera
AirLive AirCam OD-600HD User’s Manual
13
Start-up screen will be as follow no matter an ordinary users or an administrator.
Monitor Image Section
The image shot by the Network Camera is shown here. The date and time are displayed at
the top of the window.
Video Profile
The Network Camera support multi-profile for both MEPG4 and JPEG simultaneously. User
can chose the proper and/or preferred profile here.
Streaming Protocol
User can select proper streaming protocol according to networking environment.
Language
The device could provide multiple languages to meet customer’s requirement.
4 4. Operating the Network
Camera
Monitor Image
Section
ActiveX Control
Setting Menu
Video
Profile
PTZ Control
Streaming
Protocol
Language
2-Way
Audio Status Bar

4. Operating the Network Camera
AirLive AirCam OD-600HD User’s Manual
14
2-Way Audio
The device supports 2-way audio function. User can chose to enable or disable this
function by toggling the icon below.
: Disable audio uploading function.
: Enable audio uploading function.
Status Bar
Shows information of the connected device such as encoder format, image resolution,
frame per second, and bitrate.
PTZ Control
Click to display the following control panel:
Hide PTZ control:
Click the icon will hide the PTZ control function.
Camera direction:
Control camera up/down/left/right and home position.
Camera speed:
Choose the speed of Pan and Tilt.
Preset:
Add/Update the preset positions or go to one of these positions.
Camera
direction
Preset
Camera
s
p
eed
Auto pan
Tour
Hide PTZ
control
Go tour

4. Operating the Network Camera
AirLive AirCam OD-600HD User’s Manual
15
Tour:
Select one of the camera tours. Camera tour is comprised by series of preset locations.
Go tour:
Execute the selected camera tour.
Auto Pan:
Execute the auto pan of camera. While auto pan is running, the camera will swing the
camera automatically. Note that the speed of auto pan is fixed and can not be adjustable.
ActiveX Control
The plug-in ActiveX control supports a lot of functions by clicking the left mouse button.
Note that this feature only supports on the ActiveX control within Microsfoft® Internet
Explorer.
On the ActiveX control icon, click the LeftMouseButton, then a menu pop-up. This menu
provides features that are unique to the ActiveX control. These features include:
• “Digital Zoom”,
• “Record”,
• “Snapshot”,
• “Voice”,
• “Statistics”,
• “About”