AirLive MD-720 User manual

Use
r
’s Manual
720P Wide Angle PoE
Mini Dome IP Camera
MD-720

Copyright and Disclaimer
i AirLive MD-720 User’s Manual
Copyright & Disclaimer
No part of this publication may be reproduced in any form or by any means, whether
electronic, mechanical, photocopying, or recording without the written consent of OvisLink
Corp.
OvisLink Corp. has made the best effort to ensure the accuracy of the information in this
user’s guide. However, we are not liable for the inaccuracies or errors in this guide.
Please use with caution. All information is subject to change without notice
This product contains some codes from GPL. In compliance with GPL agreement, AirLive
will publish the GPL codes on our website. Please go to www.airlive.com and go to the
"Support->GPL" menu to download source code.
All Trademarks are properties of their respective holders.

Copyright and Disclaimer
AirLive MD-720 User’s Manual ii
FCC Statement
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the A
user is encouraged to try to correct the interference by one of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
FCC Caution
Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment. This device complies
with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation. For
product available in the USA/Canada market, only channel 1~11 can be operated.
Selection of other channels is not possible.
This device and its antenna(s) must not be co-located or operation in conjunction with any
other antenna or transmitter.
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance
20cm between the radiator & your body.

Table of Contents
AirLive MD-720User’Manual
iii
Table of Contents
1. Overview .....................................................................................................1
1.1 Introduction ..........................................................................................1
1.2 Features...............................................................................................2
1.3 Product Specification ...........................................................................2
1.4 System Requirement ...........................................................................5
2. Package Contents and Installation...........................................................6
2.1 Package Content .................................................................................6
2.2 Hardware Overview .............................................................................6
2.3 Hardware Installation ...........................................................................9
2.4 Connect to IP Camera .......................................................................12
3. Using IP Camera via Web Browser.........................................................15
3.1 Windows Web Browser......................................................................15
3.2 Mac Web Browser..............................................................................16
4. Operating IP Camera via Mobile Phone .................................................18
4.1 Mobile Phone Viewing .......................................................................18
4.2 Using IP Camera via iPhone..............................................................19
5. Configuration of Main Menu....................................................................20
5.1 Live View............................................................................................21
5.2 Configuration .....................................................................................22
5.3 Client Settings....................................................................................23
6. Configuration-Basic Setting....................................................................25
6.1 Account ..............................................................................................25
6.2 Network..............................................................................................27
6.3 Date Time ..........................................................................................30
6.4 Audio..................................................................................................32

Table of Contents
AirLive MD-720 User’s Manual iv
7. Camera Setting.........................................................................................34
7.1 Video..................................................................................................35
7.2 Audio..................................................................................................37
7.3 Image.................................................................................................38
7.4 E-PTZ Setting ....................................................................................40
8. Playback ...................................................................................................42
8.1 Client PC............................................................................................43
8.2 Network Storage ................................................................................44
8.3 Local Storage.....................................................................................44
9. Event .........................................................................................................45
9.1 Event Server ......................................................................................45
9.2 Event List ...........................................................................................46
9.3 Motion Detection................................................................................48
9.4 Audio Detection..................................................................................48
9.5 Tampering Detection ..........................................................................48
9.6 Schedule............................................................................................48
10. System ....................................................................................................49
10.1 Maintenance ....................................................................................49
10.2 Date Time ........................................................................................50
10.3 Security............................................................................................50
10.4 Network Basic..................................................................................51
10.5 Network Advanced...........................................................................51
10.6 LED..................................................................................................53
10.7 System Log......................................................................................53
11. Appendix.................................................................................................54
A. Frame-rate and Bitrate Table...............................................................54
B. Storage Requirement Table.................................................................59

1. Overview
AirLive MD-720User’Manual
1
1 1. Overview
This user’s guide explains how to operate this camera from a computer. A user should read
this manual completely and carefully before you operate the device.
1.1 Introduction
The AirLive MD-720 is a high-end megapixel network camera designed for professional
indoor surveillance and security applications. Megapixel (MP) IP cameras are now
available that offer a huge jump in image quality compared to the conventional surveillance
cameras. This new model complements an architecture and software that are based on
variations for professional indoor surveillance and security applications. The possibility of
viewing video from AirLive IP Cameras over the Internet is not the only one of benefits.
AirLive MD-720 is also designed to offer high-performance and is equipped with PoE port,
ensuring to power IP camera and providing network activity via one RJ45 network cable.
This advance provides an easier installation, the lower cable costs and allows placement of
AirLive POE cameras in locations with power limitation. The AirLive MD-720 is an ideal IP
camera for the applications such as hallways or stairwell.

1. Overview
AirLive MD-720 User’s Manual 2
1.2 Features
This manual will illustrate the steps of how to setup and operate this IP camera, so you’ll
also soon be enjoying the benefits of these product features.
Miniature Size Dome
30FPS at 1280x720
802.3af PoE Port
2.8mm Wide Angle Lens
Low Lux Sensor for Ultra Bright Images
Micro SD Card Slot for Local Storage
Built-in MIC, Audio Port, DIDO
Clear Motion Technology for Moving Objects
WDR Enhanced
Free 64-Channel Recording Software
1.3 Product Specification
Model MD-720
Camera Type Indoor Dome Type
Max Resolution 1280X800
Image Sensor 1/4" Mega Pixel Color CMOS Sensor
Sensor Resolution 1280X800
Board Lens
Lens Type 2.8mm, F2.0
Night Vision none
Max IR Distance none
Minimum Illumination 0.2 Lux (color)
Mechanical IR-Cut
Filter none
Auto Iris none
Viewing Angle 81° (H)
50° (V)
E-PTZ
Pan Degree-± 172°
Pan/Tile Control
Tilt Degree-± 79°
Camera
Analog Video Out none
Video Compression
H.264
MPEG4
MJPEG
Video
Video Profile 10

1. Overview
AirLive MD-720User’Manual
3
30 fps @ 1280 X 800
30 fps @ 1280 X 720
30 fps @ 640 x 480
30 fps @ 320 X 240
Resolution and
Frame Rate
30fps @ 160 X 120
Multi-profile streaming
Streaming over UDP, TCP, or HTTP
M-JPEG streaming over HTTP
(for non IE browser)
3GPP mobile view
Configurable frame rate and bandwidth
Streaming
Support both CBR and VBR
Region of Interest None
AE, AWB
Noise reduction
Color, brightness, sharpness, contrast, Hue
Mirror/Flip
Privacy Masks
Image Processing
Text, time and date OSD
Digital Zoom 10x
Audio Encoder G.711 μlaw, a law, AMR
Audio Streaming Two-way
Audio
Audio Input/Output 1 Line in, 1 Line out
Ethernet One RJ45 Port; IEEE 802.3u Compliant
10/100 Mbps Fast Ethernet with Auto-MDIX
PoE IEEE802.3af
Supported Protocols
TCP/ IP, DHCP, PPPoE, ARP, ICMP,
FTP,SMTP, DNS, NTP, UPnP, Bonjour,
RTSP, RTP, HTTP, TCP,UDP,
3GPP/ ISMA RTSP
Password protection
IP filter
Security
HTTPS
Network
Users Up to 10 simultaneous users
Power LED Amber Color
Link/Act. LED Green Color
LED and Button
Reset Button Reboot and Factory Default
(Push and Hold Over 5 Sec)
Network Processor DSP Base
System ROM 16 MByte NAND Flash
General
System RAM 128Mbyte DDR SDRAM

1. Overview
AirLive MD-720 User’s Manual 4
Power Supply none
Power Consumption 8 Watts Max.
RJ-45 10BaseT/100BaseTX
Connector Reset button
Operation: Temp: 0℃~ 50℃
Humidity: 20% ~ 85% non-condensing
Environment Storage: Temp: -15℃~ 60℃
Humidity: 0% ~ 90% non-condensing
SD card slot Micro SD
Dimension HxWxD:60.6x60.6x99 (φ)mm
CamPro Express 64,CamPro Professional
Software Search & Installation-IP Wizard II
Motion detection
Event Triggers External input via DI interface
Motion Detection 10
FTP or NAS file upload
E-mail alter
HTTP, and TCP notification
Event handler
DO (digital output) alarm
UPNP Yes
ONVIF
Open API for software integration
Application
Programming
Interface SDK
Video Buffer Pre- and post- alarm buffering
Alarm Triggers Intelligent video motion detection and
external input
File upload via FTP or email
Notification via email, HTTP
External output activation
Save to SD card
Alarm Events
Network storage
System Integration
Continuous recording Yes
OS Windows® XP, Vista, 7
Browser IE 6.0 or later, Firefox 2.0 or later, Safari
Cell Phone With 3GPP player
Viewing System
Video Player VLC, Quick Time, Real Player, Core Player

1. Overview
AirLive MD-720User’Manual
5
1.4 System Requirement
For normal operation and viewing of the network camera, it’s recommended that your
system meets these minimum requirements for proper operation:
Item Requirements
CPU Pentium 4 2.8GHz (or equivalent AMD)
Graphic Card 256 MB RAM graphic cards(or equivalent on-board graphic
cards)
RAM 1G
Operating
System
Windows 2000, Windows 2003, Windows XP, Windows Vista,
Windows 7, and Mac OS X Leopard
Web Browser Internet Explore 6 or later
Note: Please keep updating the latest Windows software and service package. (Ex: Net
Framework, Windows Media Player, Enhance ActiveX Security)

2. Package Contents and Installation
AirLive MD-720 User’s Manual 6
2 2. Package Contents and
Installation
2.1 Package Content
A user can find the following items in the package as below:
1. AirLive MD-720 is the main element of the product.
2. Bundle CD include Setup Wizard II, CamPro Express64, Video Tutorial, Quick Start
Guide, User Manual and other tools
3. Quick Start Guide provides important information and instructions for installing this
device.
4. Accessory Package
2.2 Hardware Overview
Inside View

2. Package Contents and Installation
AirLive MD-720User’Manual
7
LED Indicator
LED Color Indication
Network Blue Flash blue while network activity.
Red Steady red for booting up process.
Steady red 30 Seconds when WPS configure failed.
Blue Steady blue for booting up completion
Purple Flash purple during firmware upgrading; when reset button
pressed for at least 5 sec. to factory default
Power
Unlit When you press reset button or Power off
Reset: When the device is powered on, press the Reset Button to reboot the device. Or
hold the Reset Button for 10 seconds to set the settings back to factory default.
Reset process: Press reset button until indicator Unlit →steady red (booting up process)
→steady blue (booting up completion)
Reset to default process: Press until indicator steady blue →steady red (booting up
process) →steady blue (booting process completion)
Power Mode
Power Requirement PoE (IEEE802.3af) with Class 3
PoE Mode
PowerConsumption 2.5W
I/O Terminal Block View

2. Package Contents and Installation
AirLive MD-720 User’s Manual 8
I/O Terminal Block Pin Definition
This Camera provides an external I/O terminal block which is used to connect input/ output
devices.
The pin definitions are described below.
PIN Definition Description Max. V/A
1 Ground -
2 + 5V DC 5V DC
0.5W
3 AUDIO_In(+) Unbalanced, 1.4Vp-p, 1Vrms, terminal block -
4 AUDIO_In(+) Unbalanced, 1.4Vp-p, 1Vrms, terminal block -
5 Digital Output 1
Uses an NPN transistor with the emitter connected to
the GND pin. If used with an external relay, a diode
must be connected in parallel with the load for
protection against voltage transients.
100 mA
24V
6 Digital Input 1 Connected to GND to activate, or leave floating (or
unconnected) to deactivate. 30V DC

2. Package Contents and Installation
AirLive MD-720User’Manual
9
2.3 Hardware Installation
Follow these steps to install the AirLive MD-720 and connect all cables:
A. Hardware Installing
1. Before connecting the Ethernet cable, please use one hand to hold top cover and
another hand to press the bottom of camera.
2. Then shift top cover to left (counter-clockwise) to open the dome cover.
B. Wall mounting and Ceiling mounting
1. Attached the drill template to the wall. Drill three holes into the wall, which two for screws
and one for cable (if you want to route cables through conduit hole). Then hammer the
supplied plastic anchors into the screw holes and secure the plate with supplied screws.
2. Align the three holes on the base of camera with the two plastic anchors on the wall or
ceiling. Insert the supplied screws to the corresponding hole and screw them.
3. Adjust the angle of camera to aim the shooting area.

2. Package Contents and Installation
AirLive MD-720 User’s Manual 10
Note:
When using this device, please use an Ethernet cable without the strain relief boot.
C. Lens focus range

2. Package Contents and Installation
AirLive MD-720User’Manual
11
Rotate Notice: DO NOT rotate the lens over 2 rounds. Otherwise, the camera lens module
will be damaged.
D. Connect cables and power supply
1. The camera has only Power over Ethernet (PoE) built-in (there is no DC connector
inside.)
2. Using a standard RJ-45 network cable, connect the IP Camera to a PoE-enabled Hub /
Switch / Router.
Note:
If using a non-PoE switch, please use a PoE power injector to connect the camera
E. Completion
1. Clean the dome bubble to remove the dust and finger print.
2. Align the slide cover down to the U-shape position
3. Tighten the dome cover to the clockwise direction and make slide cover reaching the
routing hole.

2. Package Contents and Installation
AirLive MD-720 User’s Manual 12
4. The installation is complete now.
2.4 Connect to IP Camera
1. Insert the bundle CD into your PC/Laptop.
2. Auto Run Screen then shows up; click “Install Software ÆCamera IP Finder Utility” to
install the configuration tool software.

2. Package Contents and Installation
AirLive MD-720User’Manual
13
3. After completing installation, run the configuration tool software.

2. Package Contents and Installation
AirLive MD-720 User’s Manual 14
4. The Software scans the network and finds the IP Camera and then lists them in the
dialog box.
5. If the Camera’s IP address is in the same IP segment as your LAN, select the founded IP
Camera and double click on the item. Then, the default browser will show up and connect
to the IP camera’s Web automatically.

3. Using IP Camera via Web Browser
AirLive MD-720User’Manual
15
3 3. Using IP Camera via
Web Browser
3.1 Windows Web Browser
1. Open your web browser, and enter the IP address or host name of the IP camera in the
Location / Address field of your browser.
Note: If you only want to view the video without accessing Setting screen, enter
“http://<IP>/index2.htm” as your web URL.
2. Use the default account “admin” and default password “airlive”.
Note: The default user name “admin” and the password “airlive” are set at the factory for
the administrator. You can change them in the Account Menu. (Please check
“Configuration →Basic Setup →Account”)
3. The monitor image will be displayed in your browser. In the left side of main configuration
are “Configuration” and “Client Setting”. For more details, you can check the following
chapters.