airquee Arena Extreme Operating instructions

Version 1.1 29/03/17
Page 1of 10
Arena Extreme
IMPORTANT
AS OWNER/OPERATOR IT IS YOUR RESPONSIBILITY TO WRITE AND CARRY OUT
YOUR OWN RISK ASSESSMENT BEFORE ATTEMPTING TO USE THIS PRODUCT.
Site survey:
1. Carry out a survey of the area where the Arena Extreme will be located, and check for any
overhead/underground cables. It’s important that this is carried out to avoid ground
anchors penetrating underground services, and the Arena Extreme coming into contact
with overhead cables when inflated.
2. You should provide an adequate power supply to the fan, this should adhere to your local
power regulations.
3. Check wind speed: The industry recommends a maximum wind speed of Force 5 on the
Beaufort scale of 28 - 38 kmph (19-24 mph). Force 5 is a fresh breeze when small trees in
leaf begin to sway.

Page 2of 10
3X
4X
2X
16X
24X
8X
2X
4X
2X
8X
8X
8X
8X
2X
8X
8X
4X
2X
16X
8X
Included with your Arena Extreme:
Extra equipment needed in addition what is supplied with your inflatable:
•Suitable 240v Power Supply to operate the fan
Extra equipment you could consider for your new inflatable:
•Ground sheet to protect the underside of your inflatable
•Sandbag covers to anchor your inflatable indoors
•Sack truck to move your inflatable safely
•RCD to attach to your extension lead
•Crash Mats
This inflatable can be set up and packed away by 3 persons who have had
proper manual handling training and use the correct equipment to move the
inflatable.
The inflatable
in its bags
Anchor Pegs
Land Operation
Manual
Repair Kit
Gladiator Poles
Gladiator
Podiums
Basket Ball
Hoops
Volleyball Net
Adult Harness
Child harness
Adult Helmets
Child Helmets
Bungee Cords
Steel Poles
Basketball
Football
Mdf Plates
Arena Wall
Blanks
Protective
Sleeves
Skill Shot
Football Sheet
Steel Pole
PVC Handles
Carabiners
Podium
Blanking Plate
Football Net
Neck Braces Metal Bar Caps
16X
16X

Page 3of 10
Set up:
PLEASE NOTE, FOR USING THE UNIT AS A GLADIATOR YOU MUST
USE ONE SIDE OF THE BED (WITH THE PODIUM HOLES) AND TO USE
IT FOR ANY OTHER GAME, PLEASE USE THE OTHER SIDE OF THE BED.
IMPORTANT: IT IS FORBIDEN TO USE THE GAME WITHOUT THE PROVIDED NECK BRACES AND HELMETS!
Gladiator
1. Unroll the Arena Extreme bed, please ensure the blanking plates are facing upwards. This will allow
you to fit the podiums. (fig. 1a)
2. Remove the velcroed blanking plates from the podium sockets.
3. Attach podiums into the sockets. (fig. 1b)
4. Anchor the unit ensuring use of the additional anchor points located under the Velcro-flaps. See fig.
2a,b. Please refer to the EN14960 guidelines for anchorage of inflatables in the Land Manual.
5. Attach the 2HP fan to the filler pipe and ensure all additional fillers are tied off and secured. (fig. 3)
Fig. 1a
Fig. 1b
Fig. 2a
Fig. 2b

Page 4of 10
When assembled your Gladiator should look like figure 3.
FOR SAFETY REASONS THE FAN MUST BE POSTIONED/ANGLED
AT LEAST 2.5 METRES AWAY FROM THE UNIT. (SEE DIAGRAM BELOW)
Dive N Save
1. Unroll one half of the bed, ensuring the Gladiator sockets are facing the ground and are fitted with
the blanking panels.
2. Unroll one half of the netted frame work on top of the bed. Please ensure you have positioned both
halves correctly.
3. The top part of the unit connects with the bed in 3 different ways. Please make sure all of them are
connected properly:
a) When placing the top part onto the inflated bed, please make sure the following Velcro
connection points are placed on top of each other. (fig. 4)
Fig. 3
TIE IT REALLY TIGHT

Page 5of 10
b) Please connect the top and the bottom part of the unit with the sandwich Velcro seen in figure
5a, b.
c) Connect all webbing straps around the outside of the unit as shown in figure 6.
Fig. 4
Fig. 5a
Fig. 5b
Fig. 6a
Fig. 6b
Fig. 6c

Page 6of 10
4. Once inflated attach the blanking plates (fig. 7a,b) and the goal netting (fig. 8a)
5. Attach a 2 HP fan to the bed filler pipe (bottom one), and a 1.5 HP fan to the netted frameworks
filler pipe (top one). Again, please ensure all unused fillers are sealed and secure.
Skill Shot
1. Unroll one half of the netted unit.
2. Anchor unit utilizing all anchor points. See the Land Manual provided for anchoring guidelines.
3. Connect 1.5 HP power fan to standard filler pipe. Ensure all unused filler pipes are closed off and
secured.
4. Once inflated, attach the blanking plates. (fig. 7a,b)
5. Attach the Skill Shot football sheet (fig. 8b) and the goal netting (fig. 8a) with the help of their
sandwich Velcro connection.
Fig. 6d
Fig. 6e
Fig. 7b
Fig. 7a

Page 7of 10
Main unit assembly for: Volleyball, Bungee
Football, Basketball & Human Table Football
1. Follow previous above steps to construct two Dive N Save units. Ensuring they are assembled
within close proximity for ease of joining.
2. Link all the Velcro sandwiches and flaps between the two units. Ensure not to leave any large
entrapment issues.
Volleyball
Connect the 2 webbing straps to the 2 cambuckles of the net as seen of figure 10a,b.
Tip: It’s easier to connect the Velcro sandwich between the two units if
one is inflated and the other is not. This way you can easily move the
unit without the grip of the Velcro connection points shown on figure 7.
Fig. 8a
Fig. 8b
Fig. 9a
Fig. 9b
Tip: Please ensure that wherever a sandwich Velcro is in place, that the rough sides
of the Velcro are folded into each other. This is to prevent the build-up of foreign
materials and prolong the life of your inflatables Velcro. See images below.

Page 8of 10
Basketball
1. Turn off the fan to the top part of the unit so that the top sheet above the goals drops to a
reachable height. One side at a time.
2. From the inside poke the cam buckle and straps through the holes, and pull tight from the
outside.
3. You may cover the webbing straps/holes with the provided Velcro banners as seen on fig.
12.
Fig. 10a
Fig. 10b
Fig. 11a
Fig. 11b
Fig. 11c
FRONT VIEW
BACK VIEW
Fig. 11d

Page 9of 10
Human Table Football
1. Connect 3 steel poles by twisting them together. In the end you should have 8 metal
bars.
2. You may notice there is soft Velcro on both sides of the metal bars, as seen on figure 13b.
Dress the 8 metal bars with the 16 PVC caps with cambuckle on them. (fig. 13a) The caps
are equipped with hard Velcro inside that connects to the soft Velcro of the metal bar, this
way exerting grip on the bars.
3. Insert the 8 metal bars through the holes, and connect the cambuckle with the webbing.
4. Dress the metal bars with the PVC handles in the order shown on figure 15a,b.
Fig. 12
Fig. 14
Fig. 13b
Fig. 13a
SOFT VELCRO
HARD VELCRO

Page 10 of 10
Bungee Football
1. Attach the bungee cords to the MDF plates (fig. 16a), and through the holes in the sidewalls use the
carabiners to attach them to the belts. (fig. 16b) Then Velcro the disc in place over the hole.
IMPORTANT
BEFORE, DURING AND AFTER USE, THE BUNGEE CORDS, HARNESSES AND THEIR CONNECTION
POINTS SHOULD BE CHECKED FOR EXCESSIVE WEAR. IF SIGNS OF WEAR ARE FOUND, THEN PLAY
MUST BE STOPPED AND ANY WORN ITEMS MUST BE REPLACED IMMEDIATELY.
Please also check the Land Manual provided for the list of daily checks.
IMPORTANT: IT IS FORBIDEN TO USE THE GAME WITHOUT THE PROVIDED NECK BRACES AND HELMETS!
ENJOY AND HAVE FUN!
All the pictures and drawings are for illustration purposes only.
THE CORRECT PLACEMENT
OF THE PVC HANDLES:
Fig. 15a
Fig. 15b
Fig. 16a
Fig. 16b