airquee Last One Standing Operating instructions

Page 1of 14
Contents
1. Site Survey........................................................................................ 2
2. Inflatable Inclusions........................................................................... 3
3. Intended use of product .................................................................... 3
4. Operating guidelines......................................................................... 4
5. Troubleshooting................................................................................ 4
6. Hazards relating to electrical equipment ........................................... 5
7. Setup ................................................................................................ 5
7.1 Assembly of the mechanism..................................................... 6
7.2 Adding the sealed tube............................................................. 8
7.3 Assembly of the bed................................................................. 9
7.4 Assembly of the Control Panel.................................................10
7.4.1 The Control Box .............................................................10
7.4.2 Transporting and storing.................................................10
7.4.3 Positioning of the control panel.......................................11
8. Routine inspections, Trial Operations and Thorough Examinations ..11
8.1 Routine Inspections...................................................................11
8.2 Trial runs...................................................................................12
8.3 Thorough examination...............................................................12
9. Spare Parts Codes............................................................................12

Page 2of 14
Last One Standing
with Single Arm Mechanism
IMPORTANT
AS OWNER/OPERATOR IT IS YOUR RESPONSIBILITY TO WRITE AND CARRY OUT
YOUR OWN RISK ASSESSMENT BEFORE ATTEMPTING TO USE THIS PRODUCT.
1.Site survey:
1. Carry out a survey of the area where the Last One Standing will be located, and
check for any overhead/underground cables. It’s important that this is carried out
to avoid ground anchors penetrating underground services, and the Last One
Standing coming into contact with overhead cables when inflated.
2. You should provide an adequate power supply to the fan, this should adhere to
your local power regulations.
3. Check wind speed:The maximum wind speed should not exceed Force 5 on the
Beaufort scale of 28-38 kmph (19-24 mph). Force 5 is a fresh breeze when small
trees in leaf begin to sway.
2. Inflatable Inclusions:
Extra equipment needed in addition to what is supplied with your inflatable:
•Suitable 240v Power Supply to operate the fan
CAUTION! Precautions should be taken during handling and use
of the product to prevent electric shock. The blower requires a
Ground Fault Protected Circuit (GFCI). Please read the
manufacturer’s Instruction Manual before using the blower(s).
The inflatable
in its bag Anchor Pegs Land Operation
Manual Repair Kit

Page 3of 14
3X
Extra equipment you could consider for your new inflatable:
•Ground sheet to protect the underside of your inflatable
•Sandbag covers to anchor your inflatable indoors
•Sack truck to move your inflatable safely
•RCD to attach to your extension lead
•Crash Mats
This inflatable can be set up and packed away by 3 persons who have had
proper manual handling training and use the correct equipment to move the
inflatable.
3. Intended use of the product:
4. Operating guidelines:
- Before entering the game area, CLEAR INSTRUCTIONS SHALL BE GIVEN to players
on their conduct during playtime:
- NO SOMERSAULTS or any ACROBATICS allowed.
- All players remove footwear, eye wear, cell phones, keys, neck wear and/or any
sharp items.
- DO NOT allow the users to OBSTRUCT THE MOVEMENT OF THE ARM. This
includes no hanging on the arm, pushing-pulling them.
- For safety reasons, users should only stand at the designated jumping space
(numbers, podiums). Do not allow them to get closer to the middle of the bed.
- No one with ANY PRE-EXISTING INJURIES OR HEALTH CONCERNS may
use the Last One Standing game.
- Every time a user falls THE MECHANISM MUST BE STOPPED!
- Use the Emergency Button only in a case of an emergency. After releasing it, WAIT AT
LEAST 5 SECONDS before pressing any other button on the Control Box.
- The MAXIMUM NUMBER OF USERS HAS TO BE RESPECTED at all times.
The Last One Standing with Single Arm Mechanism
is designed to be usedby up to eightplayers andone
operator. The players must jump at the right time to
avoid the rotating sealed arm. The operator has
control (via the supplied control panel) over the
speed and direction of the arm to make the game
harder or easier as required. If a user is knocked over
by the arm, they should exit the game. The operator
must stop the mechanism until the eliminated player
has exited the inflatable. The last player standing is
the winner.

Page 4of 14
- The unit should NOT TO BE USED IF IT BECOMES WET. In the event of rain, the unit
should be deflated and folded to prevent water collecting on it.
- The Emergency Stop button MUST ALWAYS BE DEPRESSED AND THE KEY
REMOVED whenever you are setting up the ride or leaving the control console
unattended.
- The operator must adjust the speed of the arm to the abilities of the players.
- Do not press more than one button at a time.
- If the arm is OBSTRUCTED, RELEASE the left-right rotation buttons IMMEDIATELY.
5. Troubleshooting:
Inside the control box there is a motion controller manufactured by Yaskawa. This electronic part
is responsible for the motion of the sealed arm. Any incorrect usage of the mechanism could result
in Yaskawa producing an Error Code, which means the mechanism stops responding to the
operator’s commands.
Most of these error codes are built in safety mechanisms, protecting the electric motor. When
experiencing this sudden stop, our advice is to follow these simple steps:
- Turn OFF the mechanism, then ON with the Main On/Off key. This will reset the
Yaskawa settings and you should be able to resume playing.
- If that doesn’t help, unlock the top of the Control Box with the supplied triangle key, and
reset the settings manually by pressing the RESET button. (see figure below)
CAUTION! TAKE EXTRA CARE WHEN OPENING THE CONTROL BOX.
DO NOT TOUCH ANYTHING ELSE BESIDES THE RESET BUTTON.
Issue
Steps to take
Short circuit or ground fault
on the drive output side:
Try connecting the motor directly to the main supply. In case it is
used with an extension cord, make sure not to connect to many
things to the same extension lead.
The motor is operated at low
speed with heavy load:
Make sure you remove the obstacle from the motor that keeps it
stopping. Please note you are not allowed to add anything to the
middle bar of the mechanism. Make sure that when a player is
on the sealed arm the mechanism is stopped and is not moving
forward.

Page 5of 14
If you still have issues with the mechanism, please contact Airquee
customer support on the following number [phone].
To avoid getting an error code:
- Make sure the electric power supply is stable and not fluctuating in any way.
- Make sure all the cables are connected properly: the motor with the control box, and the
control box to the main electric supply.
6. Hazards relating to electrical equipment:
The use of portable electrical equipment involves the potential risk of electric shock, burns or fire. A
major cause of accidents is failure to maintain equipment. The risk can be managed effectively if
sensible and appropriate rules for use and maintenance are applied!
1. The most important rule when handling the mechanism is to ALWAYS DISCONNECT IT
from its power source when ASSEMBLING THE UNIT, opening the control box or the
drive motor. (the only case when this doesn’t apply is when you manually reset the
Yaskawa).
2. The control box and the wiring used within the game are NOT WATER PROOF OR
WATER RESISTANT, therefore we do not recommend operating the unit in the rain.
Using electrical equipment in wet or damp conditions can be dangerous. If you suspect
water has entered any of the electrical components they should not be used until
completely dry and tested. We recommend taking professional advice where necessary.
3. All cables and electrical equipment must be tested in accordance with the regulations of
your country.
4. In accordance with HSE (UK) guidelines, all 240v equipment should be protected with an
RCD (Residual Current Device) having a maximum trip current of 30 mA. RCD’s are
available from Airquee or your electrical store.
When using it with a generator, make sure it has an output of more than 4 kVA (kilo-volt-ampere),
and a stable 230 Volts on 50Hz.
7. Setup:
7.1 Assembly of the mechanism (AQ4816SP4):
CAUTION! MAKE SURE THE MECHANISM IS NOT
CONNECTED TO A POWER SOURCE WHEN ASSEMBLING IT!
Cycle times of acceleration
/deceleration:
If you are sure thatthis isthe case, and we would need to change
the values, please contact [e-mail] for further
assistance.
Overvoltage:
The motor will give an error code if the input voltage is too high.
Make sure you change the generator to a smaller one.

Page 6of 14
x4
x4
x4
The mechanism consists of:
- Place the drive motor cover on top of the
drive motor, then insert the wheels and
tighten them with the supplied bolts.
- Unfold the bed at the desired location
and move the drive motor to the center
of the bed.
Sealed Tube
with PVC cover
Drive Motor
Spring Cover
Drive Motor
Cover
Bed Hole
Cover
AP2963
AP2786
AP3149
AP3152
Metal Arm
Middle Bar
Wheels
Legs
Leg Covers
MP0049
MP0022
MP0004
MP0003
AP3151
BED

Page 7of 14
- Exchange the wheels with the legs.
- Insert the middle bar into the drive motor’s
shaft and tighten the bolts at the desired
height. We recommend the second and third
holes at least.
- Insert the metal arm and tighten both
bolts (the upper and the spring bolt).
MAKE SURE BOTH BOLTS ARE ACTUALLY INSIDE A
HOLE BEFORE TIGHTENING THEM. THIS WAY YOU
PREVENT THE BOLTS SCRATCHING THE MIDDLE BAR!
THIS BOLT ADJUSTS
HOW HIGH THE ARM
CAN JUMP
MAKE SURE THE SURFACE WHERE
YOU PLACE THE MECHANISM IS LEVEL!

Page 8of 14
- The spring has a screw thread, which allows it to be tightened manually.
It will be easier if you loosen the spring before you add the metal arm to the middle bar.
7.2 Adding the sealed tube:
DO NOT INFLATE THE SEALED TUBE
BEFORE YOU SLIP IT ON THE ARM BAR!
- Slip the sealed tube on the metal arm, using
the highlighted hole.
- Inflate the sealed tube through the valve with
the help of the supplied hand held fan. When
deflating the sealed tube, you must PRESS
THE MIDDLE OF THE VALVE, this way
opening it. You can close the valve by
pressing its middle again. Don’t forget to fit the
cap on the valve after inflating.
- Bind the webbing around the middle bar
and tie the eyelets with the supplied rope.
- The highlighted PVC loop is for pulling the
uninflated sealed tube in its cover. Make
sure it is hidden when using the LOS. It may
harm users when rotating.
- Cover the spring with the spring cover.

Page 9of 14
- Connect the drive motor to the control
panel with the 12m cable. The electric
socket can be found inside the drive motor.
7.3 Assembly of the bed:
- Start connecting the sandwich Velcro flaps. The easiest way to connect the
flaps is to first patch the lower part of the Velcro all the way, then cover the top
part of the right side soft Velcro with the left side hard Velcro flap.
- You may inflate the bed. While inflating, adjust the position of the bed around the
mechanism with the help of the anchor points, to make sure the mechanism stands in the
middle of its designated hole.
- After inflating, add the bed hole cover.
- Add the podiums/numbers.
THE LOWER PART OF THE SANDWICH VELCRO
Step 1
Step 2

Page 10 of 14
7.4 Assembly of the Control Panel:
The Control Panel consists of:
- You must bolt these 3 parts together to make
it stable.
7.4.1 The Control Box:
1. 12m cable electrical output socket.
2. Main power cable.
3. Main On/Off switch. It works only with the supplied keys.
4. Emergency Stop: In case you must stop the mechanism
suddenly.
5. This will light up when the control panel is under power,
and the key is turned to ON.
6. You can change the movement direction of the arm.
7. Adjusting the speed of the arm.
8. Key hole to open the control box.
7.4.2 Transporting and storing
When packing away the mechanism for transporting/storing, we advise to:
- remove the keys of the control box.
- do not place anything heavy on the control box or on any part of the mechanism.
- make sure the mechanical parts are packed and protected correctly.
- store the mechanism in dry conditions/in a dry place.
Control Box
Support Bar
Legs
ON/OFF
Key
Triangle
Key
12M Cable
3M Cable
AP2785
MP0013
MP0012
MP0056
MP0015
MP0008
MP0009
1
4
2
5
7
6
3
8

Page 11 of 14
- not to remove the cover from the sealed tube.
- leave the bolts and nuts on the mechanism in their corresponding holes.
- dry every part (if for any reason it becomes wet).
7.4.3 Positioning of the control panel:
The control panel must be placed at the entrance, at an approximate distance of 1.5M, so that the
operator has an unobstructed view of ALL the players.
8. Routine Inspections, Trial Operations and Thorough Examinations:
8.1 Routine inspections (before every use)
After every setup or operation, before opening the game to the public, the controller or his nominee
SHALL PERSONALLY CHECK that the setup of the Last One Standing is correct.
We recommend to check for every criteria written below. The person carrying out the check shall be
sufficiently trained or experienced in the check routines that have to be carried out.
Check that: - every button is in a working condition on the Control Panel.
- the electrical connection sockets and cables are not chafed nor damaged.
- the Velcro of every cover has a good grip and is not weakened, the covers are
not damaged and no accessible parts of the machinery has sharp edges,
sharp angles or rough surfaces to cause injury, and no openings which can
“trap” parts of the body or clothing.
- the webbing cam buckles of the sealed tube is not damaged, including the
stitching of the cover of the sealed tube.
- the stitching of the bed and walls do not have tears, rips which could represent
a safety hazard.
- the metal arm and spring does not have any sign of damage.
- all nuts and bolts are secure and tightened.
- the inflatable bed is securely anchored.
OPERATOR/CONTROLLER
ENTRANCE
FIELD OF VIEW

Page 12 of 14
The mechanism has only 1 lubrication point. This
bearing has already a sufficient inner lubrication, but if
lubrication is deemed necessary, manual lubrication
can be applied through the hole highlighted on the
picture.
The device shall not be made available to the public until any adjustments or repairs judged to be
necessary as a result of this inspection have been completed.
8.2 Trial runs
Following the check, the controller shall run one or more trial runs without any members of the public
on it, simulating where possible emergency situations to verify particularly that the control system
and the emergency stop works properly. Only NOW ARE THE PLAYERS ALLOWED TO ENTER
THE UNIT.
8.3 Thorough examination
Besides the regular checks, the Last One Standing should be thoroughly examined at appropriate
intervals by a competent person/institute/organization/company.
The intervals between two successive thorough examinations may be governed by existing national
regulations:
9. Spare Parts Codes:
Code and Name
Description
MP0002 - Shock Absorber Spring
Holds and adjusts the height of the inflatable arm.
MP0003 - Drive Motor Leg
Stabilizes the Drive Motor.
MP0004 - Drive Motor Wheel
For moving the mechanism.
MP0005 - 10 x 30 mm bolt
To fix the Legs to the base of the Drive Motor and to adjust the
height of the Arm Bars.
MP0006 - 12 x 60 mm bolt
To fix the Metal Arms to the Middle Bar.
MP0007 - 8 x 50 mm bolt
Used to fix the Shock Absorber Spring to the 1m Metal Arm
and the Middle Bar and to fix the Control Box to its supporting legs.
MP0008 - 12m Cable
To connect the Control Panel to the Drive Motor.
MP0009 - 3m Cable
To connect the Control Panel to the main electric socket.
MP0010 - Set of Inner Hexagonal Bolts
To fix the Middle Bar to the Drive Motors Shaft.
MP0012 - the Legs of the Control Panel
To stabilize the Control Panel.
MP0013 - the Support Bar of the Control Box
The middle part of the Control Panel.
MP0015 - Triangle Key of the Control Box
To lock the Control Box.
MP0016 - Emergency Button
To stop the movement of the arms in case of an emergency.
MP0017 - Green Button
MP0018 - Red Light
MP0019 - Potentiometer
BEARING

Page 13 of 14
MP0031 - Middle Bar
MP0027 - Allen Wrench
To assemble\disassemble the mechanism.
MP0029 - 13mm Wrench
To assemble\disassemble the mechanism.
MP0030 - 19mm Wrench
To assemble\disassemble the mechanism, to connect the inflatable
arm to the middle bar.
MP0049 –1M Metal Bar
To hold the sealed tube.
MP0056 –ON/OFF Key
AP3149 - Drive Motor Cover
To cover the top of the Drive Motor.
AP3150 –Middle Bar Cover
To cover the Middle Bar.
AP3151 –Leg Covers
To cover the legs of the Drive Motor.
AP3152 –Bed Hole Cover
To cover the gap between the Drive Motor and the inflated Bed.
See the location of every spare part on the pictures below:
MP0027 MP0029 MP0030

Page 14 of 14
ENJOY AND HAVE FUN!
Legal Disclaimer:
The Airquee Operation Manual (the "Manual") is proprietary to Airquee Ltd and no ownership rights are hereby
transferred. No part of the Manual shall be used, reproduced, translated, converted, adapted, stored in a retrieval
system, communicated or transmitted by any means, for any commercial purpose, including without limitation, sale,
resale, licence, rental or lease, without the prior express written consent of Airquee Ltd.
Airquee Ltd does not make any representations, warranties or guarantees, express or implied, as to the accuracy
or completeness of the Manual. Users must be aware that updates and amendments will be made from time to time to
the Manual. It is the user's responsibility to determine whether there have been any such updates or amendments.
Neither Airquee Ltd nor any of its directors, officers, employees or agents shall be liable in contract, tort or in any other
manner whatsoever to any person for any loss, damage, injury, liability, cost or expense of any nature, including without
limitation incidental, special, direct or consequential damages arising out of or in connection with the use of the Manual.
All logos, images and content not owned by Airquee Ltd are copyright to their respective owners and have been
reproduced by permission.
Your product model, and its inclusions (number and type) may differ from the one presented in this manual. All the
pictures and drawings contained in this manual are for illustration purposes only. Version 1.7 08/02/18