Airwheel R6 User manual

USER MANUAL
R6

- 02 -
Saddle
components
Bike body 1pcs Pedal 1unit
Charger 1pcs Tool 1unit
Instruction 1unit Saddle components 1unit
Tool
Charger
Packing list
Pedal
Bike body
Instruction
Check Packing Contents

- 03 -
Rear brake
Front brake
Handle
Lifting rod lock catch
USB charging interface
(compatible with mobile
phones and digital equipment)
Front wheel Charging mouth
Headlight,Horn
Front fender
Disc-brake
Pedal
Saddle
Dashboard
Rear fender
Motor
Taillight
Locking handle
Adjustable switch
Power switch
Handle to
accelerate
Kickstand
Extended gear
Stop gear
Contractive gear
R6 Diagram
Headlight
power switch
Horn switch
R6S
(Power-assisted mode)

- 04 -
Main Technical Parameters
Warning
Please do not throw away the waste battery, so as not to pollute the environment. The waste lithium
battery of the product is to be recycled by the enterprise or dealer, and the government designated
outlets.
To start it normally, please ensure the adjustable switch is placed in the stop gear. After extension or
contraction, please ensure the adjustable switch is placed in the stop gear.
Size 1220X550X950mm Item weight ~ 19.2kg
Folding size 910X400X750mm Max. load 100kg
Tire size 14 inch Max. speed ≤ 20km/h
Charging voltage AC220V 50-60Hz Max. permissible gradient ~ 15°
Charging time ~ 200min Battery capacity 244.2wh
USB output voltage 5V Applicable temperature -10℃~40℃
Specications
Motor type Brushless motor Nominal voltage 36V
Continuous power output 230W Rated output torque 5.7N.M
Rated speed 380r/min
Main Technical Parameters Of Storage Battery
Main Technical Parameters Of Motor
Main Technical Parameters Of Controller And Charger
Storage battery type Lithium battery Nominal voltage 36V
Undervoltage protection value ≥ 30.5V Over-current protection value ≤ 18A

- 05 -
R
Take R6 from the box, open the lifting rod lock (see Figure 1 - ①arrow), insert the front into the folding riser (see
Figure 1 - ②arrow), then close the lock, push the head to the vertical (See Figure 2); fold the handle down (see Figure
3 - ③arrow) to catch the groove, and then buckle up (see Figure 4- ④arrow); open the saddle lock, install the saddle
and adjust to suitable height(See Figure 5- ⑥arrow); then turn the brakes and dashboard to the horizontal position (see
Figure 6), tighten the screws on brakes to x the brakes (see Figure 7).
Install the pedals (See Figure 8), L for left and R for right. Please pay attention to the installation of the screw
thread. The left pedal is counterclockwise tightened, right pedal clockwise tightened, and the recommended pedal
torque is 35 ~ 40N.m. Start the power (see Figure 9), release the locking handle (see Figure 10- ⑦arrow); set right
the bike body and put the adjustable switch in the extended gear (see Figure 11). The body automatically unfolds,
and when nishes, put the adjustable switch in the stop gear, close the locking handle, turn off the power (see
Figure 12).
1
2
Figure 8
Figure 10
Figure 12
Figure 1 Figure 3
Figure 7
Figure 4 Figure 5 Figure 6
Figure 2
①
②
⑤
⑥
Lifting rod lock
Saddle lock
Power switch
Figure 9
Figure 11
④
③
⑦
Adjustable switch
Extended gear
Locking
handle
Screw
Folding
handle
Folding
handle
Use the Bicycle

- 06 -
R6 provides riders with three different riding modes.
1.Electricity-assisted mode
Set right the head, fold kickstand and fasten frame. Adjust bike head and saddle position to ensure a
comfortable riding experience. Find the power switch in the one side of the batter, start it and hold the handle.
First sit on the saddle and step on the pedals one foot by one foot. When riders are ready to ride it, they can
push the accelerator in the right handle to accelerate.
Go forwardGet on Brake
Get Started
Power switch
Turn the accelerator handle down with
right hand, and the motor speed increases.
Release and go back to zero gear.
Long press the brake button,
release it when slow down
or stop.
Handle to
accelerate
Open the power switch .
Starting is completed.
Rear
brake Front
brake
R6S does not support pure electric mode.
3. Power-assisted mode
Turn on the power switch. Power sensor can sense the rotation, and then give signal to the controller when the
riding ring exceeds three rings, so that power-assisted mode is activated. According to different riders' force,
the level of power assistance changes. When braking, it is out of power-assisted mode. If pedals reverse, it will
realize a faster exit of power-assisted mode. The power-assisted mode is to make riding easier.
2. Man-powered mode
Set right the head, fold kickstand and fasten frame. Adjust bike head and saddle position to ensure a comfortable
riding experience. Find the power switch in the one side of the battery, start it and hold the handle. First sit on the
saddle and step on the pedals one foot by one foot. Rides can pedal it to go forward.
Learning Skill
Turn the accelerator handle down with
right hand to accelerate
Fold the kickstand, open the power switch
and step on the pedal one foot by one foot. Hold the brake.

- 07 -
Operating steps for beginners (electricity-assisted mode)
Fold the kickstand and turn on the power switch. Hold the handle and sit on the saddle.
One foot steps on the pedal and look straight ahead. Turn the accelerator handle down with right hand to accelerate.
When riders need to slow down or stop R6, riders put their ngers on the brake handle, and press the brake
handle hard until the scooter slows down or stops.
When the brake is started, the accelerator will automatically cut off power.
1.
2.
3.
4.
Avoid using this product in bad weather conditions (e.g., rain, snow, or ice).
Please conrm whether the brake can be used normally when riders want to use it.
Safety
Please read User Manual carefully and follow riding requirements during the R6 ride. Please do not use it until riders have
read User Manual carefully and learned the performance well. Do not lend it to those who cannot manipulate e bikes.
Important Note:
No urgent acceleration, rapid deceleration and sharp turns. Do not excessively lean forward and backward. Do
not over speed. When the power switch lights ash, it is recommended that the rider stop riding. If riding, please
keep a low constant speed. If there is a risk of falling, please protect personal safety rst, do not consider R6.
R6 may produce wear and tear which may inuence on the performance in the process of riding and parking.
So before riders ride the R6, it is necessary to do the following inspections:
Rider needs to check whether the R6 is installed rmly, and is damaged or not.
To install pedals, 35~40N.m is the recommended torque. Please make sure the pedals have been fastened
before use. If not, the rear screw tooth will be damaged and the pedals will fall off from the bike which is not
included in the Warranty.
Rider needs to check the brake function and tyres, and to check whether the handle and folding lock is
fastened. If not, please tighten the screws.
Rider needs to check whether folding mechanism has been locked.
The chain should be tightened meaning that the distance between chain prolapse and tension is 10~15mm.
Brake should be reliable and exible to reset and it should increase the braking distance in rainy, snowy and
downhill riding.
Adjust the handlebar, saddle height, and it must not be higher than the safety points on the vertical pipe
and the saddle tube. After adjustment of the horizontal pipe, the vertical pipe, saddle and saddle tube, they
should be fastened, ≥ 18N.m is the recommended torque.
Rider needs to nd an open space to practice, at least 4m*20m area, indoor and outdoor.
Rider needs to have a full understanding of the surrounding environment to avoid the interference from the
vehicle, pedestrians, pets, bicycles and other obstacles.
Rider needs a skilled assistant in the side. The assistant is procient in riding R6 and familiar with the
guidelines for the use of scooters in all matters needing attention and riding method.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
You need lots of practice to grasp the skill before you ride R6 safely. If you are not skilled, or fail to follow the user
guide of this product, it may cause rider or others injury or property loss. Our company only takes the responsibility for
product defects or damage, and we are NOT responsible for physical injury or property loss related with using products.
Parking note:
When you get off, you should turn off the power in case of accident caused by the bike accelerates suddenly.
The power should be turned off when parking.
For your riding safety and for the R6's superb condition, please maintain and clean it regularly.
1.
2.
3.

- 08 -
1.
2.
3.
4.
5.
6.
7.
1.
2.
3.
4.
5.
6.
Newly purchased vehicles should be adjusted in good condition, if there is any question, please refer to the
aftersales staff.
The adjustment method of the brake is the same as the ordinary bicycle. The key is not only to be able to brake
effectively, but also to release the brake without block (otherwise it will consume a large amount of electric energy)
and make sure the brake-power off function is effective.
To replace tires, it is the same as ordinary bicycle. Due to the rear wheel hub and circuit, riders need to pay
attention to the lines and press the two screws in the rear axle. The torque of the rear wheel is recommended
≥ 30N.m, the front wheel ≥ 18N.m.
Have a maintenance and a comprehensive examination every 800 km. check whether the front and rear wheel
screw is locking, check whether the pattern of cover tyre is worn; check whether the tire pressure is appropriate,
the drive system is smooth, and each part of the joint is normal: check whether the brake line zip-fastener is used
in lubrication. And inject suitable amount of lubricant to the central axis, the front axle, rear axle, ywheel, fork,
rotating parts and brake wiring. 40# oil and butter as a lubricant are recommended.
In the use and maintenance, if you nd that you cannot solve the problem, please contact the aftersales staff.
Unauthorized demolition of Airwheel caused the failure and damage, is not in the company's free warranty.
When the vehicle is used for a period of time, it should be requested professional or designated service station for
a comprehensive inspection and adjustment to ensure the comfort, safety and normal service life.
Adjustment and maintenance:
Chain adjustment:
Rotate to loosen the nuts. Adjust the nut forwards or backwards to nd the suitable looseness. When adjusting the
chain, it must also be aligned with the rear nut and adjusting nut and keep the front and rear wheels in a straight line.
After adjustment, refasten the nut in the rear wheel, lock the adjusting nut to have a nal check. The chain sag between
the two chain wheels should be 10~15.
Battery usage:
Auxiliary charge: such as short delivery time, users can directly use the battery.If the delivery time is longer (2 months
or longer), the battery will lose power during storage and transport. It is better to charge the battery before use. To
charge it requires plugging the exclusive charge to the battery charging hole and connecting AC220V power source for
2~4 hours until the charger is full.
The normal charge of the battery: the operation of R6 is also the discharge process of the battery. The battery should
be charged immediately after the use of the power-assisted vehicle.
Please turn off the power if not riding.
The connectors of the battery box should be xed tightly according to the requirements (the battery box connecting line
has been reliably connected before ex-factory). Loosened or wrong connection will cause the related parts abnormal
and lead to serious damage.
Lithium batteries can not be close to open re or high temperature heat source, can not be thrown into water and can
not be exposed in the sun in high temperature season.
Do not disassemble and decompose, as the internal part of them lithium battery has been packaged intactly.
The waste lithium battery of the product is to be recycled by the enterprise or dealer, and the government designated
outlets. Please do not throw away the waste battery, so as not to pollute the environment.
The right side of the bike
Adjusting nut Rear nut
The left side of the bike
Charger usage:
Carefully check whether the charger's rated input voltage (AC220V) and the grid voltage is consistent.
When the vehicle needs charging,rst connect the battery to the charger, and then connect the charger to AC power
source.The charging indicator is red meaning it is charging. When it turns green, it will take 15 minutes to be fully
charged. The charging time is about 2-4 hours (depending on the quantity of remaining battery).
1.
2.

- 09 -
When charging, please put it in the safe place where children can not touch.
It is not advised to use it when it is not fully charged.
Do not use other brands of chargers, and other brands of batteries are not suitable for the use of the charger.
Do not disassemble, as the charger contains high voltage circuit.
Prevent liquid and metal particles from penetrating into the inside and be aware of falling and impact, so as not to
cause damage during use and storage.
When charging, do not afx any items.
Matters needing attention when charging:
1.
2.
3.
4.
5.
6.
Do wear helmet, gloves, elbow/knee pads or other necessary protection gears.
Do conrm the reliability of brake, saddle, frame, handle and wheels in case of accidents.
Riders should pedal it when climb bridge, ride against the wind and overload.
Do not ride on the bumpy and wet roads, such as earth road, cobbled road or snowing and watery roads, in case of
accidents and danger.
Do not put items in the handles as it may be out of control.
R6 is only suitable for one person to ride. Do not carry person in the storage rack.
Do not ride Airwheel in extremely cold winter.
Do not ride Airwheel in the rain.
Don't ride overspeed in the downhill. If brake, do not use the front brake in high-speed riding, in case of danger.
Do not inject oil in the brake in case of braking failure.
Do not allow pregnant woman, children under 15 or the aged above 60 to ride Airwheel.
Drunk or drug riding Airwheel is prohibited. People with constrained action and reaction capacity are not allowed to ride
Airwheel.
Do not ride Airwheel in other unadvised situations causing by either personal or objective reasons.
R6 is not suitable for long-distance travel.
Develop good habits to charge in time. Before ride, please ensure R6 has enough electricity. It is very important to
form the habit of charging in time every day so that the battery can serve you a longer period of time.
Almost all kinds of batteries will be affected by the environment. In general, the electric discharge performance is better
when the air temperature is high. When the temperature drops to 0 degrees centigrade, battery power may fall more
than 1/3. So, in winter or in cold area, mileage reduction is normal. When the temperature rises to 20 degrees above,
the range will recover.
Do not insert metal objects (such as wires, keys etc.) into the battery charging hole or put in the +/- contact, so as to
avoid the short circuit of the battery, ignition and safety loopholes.
Do not use other brands chargers and accessories or there may occur accidents and Airwheel is not responsible for
the accidents.
Lithium batteries cannot be close to open re, and ammable and explosive corrosive gases.
Do not disassemble and decompose the battery, so as not to damage the internal parts.
It is strictly prohibited to use wire or conductor to connect the battery, so as to avoid danger and damage to the battery.
The lithium battery should be handled with care, to avoid accidents.
To charge, rst connect the battery charge interface, then the power source.
It needs power off to store. It needs to charge no more than 3 months and then store it.
The company shall not be liable for any loss or damage resulting from self-ret and self-repair, which may cause you
to lose your free warranty scope. If something goes wrong, please contact aftersales personnel.
This product might be limited to use on private road (check the regulations in force in the territory of use). We recomm
end using suitable protective equipment and installing reector.
Attention:
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
25.
26.
Airwheel reserves the right of nal interpretation of all the terms and conditions of this User Manual.

- 10 -
Fold the kickstand, lower the head and saddle height to the minimum (see Figure 13). Turn on power (see
Figure 14), release the locking handle (see Figure 15 - ⑧arrow); set right the body, put the adjustable switch in
the contractive gear (see Figure 16). The body automatically folds, and when nishes, put the adjustable switch
in the stop gear, close the locking handle, turn off the power (see Figure 17).
Figure 18
Figure 19
Button
Folding handle
⑨
⑩
1
2
Push the button on the folding handle (see Figure 18- ⑨arrow) and fold down the folding handle
(see Figure 18 - ⑩arrow) to fold the head as shown in Figure 19 - ⑪(see Figure 20). The pedals are
pushed down (see Figure 21- ⑫, 21 - ⑬arrow), and fold the pedals to complete the folding.
Figure 13 Figure 17
Figure 21 Figure 20
⑫
⑬
Locking
handle
Figure 16
Figure 15
Power switch
Figure 14
⑧
⑪
Adjustable switch
Contractive gear
Airwheel reserves the right of nal interpretation of all the terms and conditions of this User Manual.
Foldable

- 11 -
Dashboard
DISODO
Mp/h
km/h
Key 1
Speed
Voltage level
Electric mode
is on
Gear adjustment
Multi-function
display
Option key
Key 2
Introduction of Keys
Open the battery switch, and the dashboard can be seen. Short press the option key, the interface
switching among the ODO, VOL, E (error), A (warning) and DIS.
Mode setting
Long press the key 1 and key 2 (about 3 seconds) simultaneously to set the mode
P01: backlight brightness, 1 darkest, 3 lightest;
P02: Number of speed measuring magnets: Range: 1-255;
P03: wheel diameter: unit inch; precision: 0.1; range: 5.0-50.0;
P06: Power switching mode
0000: electricity mode is closed.
0001: electricity mode is opened. (The moped mode has no such function. )
Parameter modication
In a certain parameter state, short press key 1 and key 2 to switch parameters. After modication,
short press the option key to switch to the next parameter, and save the previous parameter;
when parameter modification is completed, long press key 1 and key 2 to exit the settings
interface. Or wait 10 seconds to automatically exit and save the parameters.
Gear adjustment
In the dashboard interface, short press key 1 and key 2 to adjust gears from 1-9 (0000).
The In the dashboard interface, short press key 1 and key 2 to adjust gears from 1-9, A, B, C, D, E,
F and H, a total of 16 gears (0001) .(The moped mode has no such function. )
Other Functional Instructions

- 12 -
Uncover the dust cap in the battery
box and connect the charger to
charge.
Battery lock
Power
connecting wire
Top tightening screws
Insurance pin
standard
customized
Top tightening screws
Battery box can be disassembled.
Separate the battery box wire and
frame line before removing the battery
box ( to install battery, insert the battery
box rst and then connect).
30 batteries (standard)
First loosen the top screws, pull down
the insurance pin, remove the battery
box to the direction of the top tightening
screws (as shown in the figure), then
take out the battery box to charge.
40 batteries (customized)
First loosen the top screw, open the
battery lock with R6's matched key,
and then move the battery box in the
opposite direction of the battery lock(
as shown in the gure), then take out
the battery box to charge.