Alango Technologies BeHear ACCESS User manual

[email protected]
www.alango-behear.com
Quick Start
Guide
TV LISTENING SYSTEM
BeHear ACCESS + HearLink PLUS
[email protected]
www.alango-behear.com

1. Connect HearLink PLUS to a power outlet (a) or the TV set’s
USB port (b) using the supplied USB power cable. HearLink
PLUS will turn ON automatically.
TV
a
b
Remove for
Bypass use
TX
TX Verify that the mode switch
is set to TX position
2. Connect the HearLink PLUS TX port to the TV (or other
media device) via the supplied optical or 3.5mm audio
cable. The active connection type is indicated by the
illuminated text ( or ).
OPT AUX
Remove for
Bypass use
AUX OPT
Make sure to remove the plastic
protectors from the optical cable
terminals prior to insertion.
Getting Started
A
2

3. Turn on the BeHear ACCESS headset
by pressing the Power button and
holding it until the unit vibrates
and the LED turns light blue.
A voice prompt will be played.
4. Successful connection of the BeHear ACCESS is
indicated by the illuminated A on the HearLink PLUS
panel.
The LL is illuminated to indicate that the Low Latency
APTX-LL Bluetooth CODEC is being used.
LL
A
If the automatic connection is delayed, briefly
press the BeHear ACCESS Power button to
reconnect it to the HearLink PLUS transmitter.
3
Power button
LED indicator

Press to increase the volume. A tone is played
when maximum volume is reached.
Press to decrease the volume. A tone is played
when minimum volume is reached.
Short press to toggle audio Play/Pause.
1. HearLink PLUS Manual Control
Press to decrease the volume. A tone is played
when minimum volume is reached.
Press to increase the volume. A tone is played
when maximum volume is reached.
Short press to toggle Play/Pause audio.
2. BeHear ACCESS Remote Control
Manage audio play using the headset’s left-hand controls.
4
Audio Playback
B

Helpful Information
C
5
2. If you do not hear audio:
Ensure that the ‘audio out’ port of your TV connected to
the HearLink PLUS is active. For some devices you need
to enable the audio output. Refer to your device’s user
manual.
Toggle the Play/Pause button on the BeHear
headset's left-hand control box or button on the
HearLink PLUS.
2
Wall plug purchased separately
1
3
1. To charge the BeHear ACCESS headset, connect the small
end of the supplied micro-USB cable to the charging
cradle, and the large end via a power adapter to a wall
socket (or directly to a USB port).
The LED indicator is red during charging and turns green
when the headset is fully charged, typically within 2-3
hours.

6
TX
AB
When pairing is complete (after 5-30 seconds) will
be illuminated on the HearLink PLUS panel.
Successful connection of the BeHear ACCESS headset
is indicated by the illuminated or on the HearLink
PLUS panel.
TX
4. To restore connection between BeHear ACCESS and
Hearlink Plus transmitter:
Place HearLink PLUS into pairing mode with a short
press on its button.
When in pairing mode the indicator light will flash TX
quickly.
Turn OFF BeHear ACCESS.
Press its Power button and hold it until the voice
prompt says: “Pairing mode active” and the LED blinks
in alternating red and blue.
Place the BeHear ACCESS headset close to the HearLink
PLUS device.
3. If the automatic connection is delayed, briefly press the
BeHear ACCESS Power button to reconnect it
to a previously paired HearLink PLUS transmitter.

5. Use the HearLink PLUS Bypass mode to maintain the
existing interfaces between your TV and peripheral
audio equipment.
Remove protection sticker from the rear panel and
connect the Hearlink PLUS TX port to the TV via the optical
or 3.5mm audio cable, and the RX port to a speaker or
other peripheral audio equipment using the same type of
cable as the TX port connection.
To passthrough HearLink PLUS
set its Mode switch to Bypass
position, indicated by .
Bypass
AUX OPT
AUX
OPT
Remove the sticker to expose the RX ports.
Non-Wireless Speaker
7
6. More details about Hearlink Plus and BeHear ACCESS
can be found in their user manuals.
[email protected]
www.alango-behear.com
To restore connection with the
BeHear ACCESS headset set the
Mode switch to TX.
TX