Alarm Lock Trilogy Networx AL-IME2-EXP User manual

1
OVERVIEW
The Trilogy Networx™AL-IME2-EXP Expander extends
the coverage area of version 2 series Gateways, allowing
control of up to its rated maximum of 63 Networx locks per
Gateway. Installation is simple, as the Expander only re-
quires a connection to an AC outlet.
AL-IME2-EXP Expanders are cost-effective, easier to wire
than conventional Gateways, and feature a simplified 'Plug
and Play' setup where the Networx system automatically
identifies all newly powered Expanders and quickly deter-
mines the best wireless signal pathways. Up to 7 Expanders
can be added to one version 2 series Gateway.
Why use AL-IME2-EXP Expanders?
 Less costly, Expanders can be used in place of addition-
al Gateways
 Does not require network access / Ethernet cables
 Extends wireless lock signal coverage
 Reach otherwise troublesome locks in areas of insuffi-
cient signal strength
 Allows for easier (flexible) positioning of version 2 Gate-
ways
 Allows large area signal coverage with a single network
connection to the Gateway
Note: Expanders are available in two different designs,
the AL-IME2-EXP and the AL-IME2-PIE Plug-In Expander
(identical in operation, the compact AL-IME2-PIE plugs di-
rectly into a standard 120VAC un-switched/uninterruptable
wall outlet).
Version 2
The AL-IME2-EXP "version 2" Expanders (notice the "2"
in the model name) are the next generation of Networx wire-
less devices. Because AL-IME2-EXP Expanders only
work with version 2 Gateways, a version 2 Gateway must be
installed and operational in your system for AL-IME2-EXP
Expanders to function (AL-IME2-EXP Expanders cannot
communicate with older "non-version 2" Gateways).
Note: Although the version 2 Gateways and AL-IME2-
EXP Expanders CAN be mixed into an existing system
that includes older "non-version 2" Gateways, at least one
new version 2 Gateway must be up and running before an
AL-IME2-EXP Expander can be used.
IMPORTANT: DL-Windows version 5.4.2 or later is re-
quired to support version 2 Gateways and Expanders.
The AL-IME2-EXP Expander is compatible with Alarm
Lock and Continental Access products. Refer to the docu-
mentation supplied with your software for integration details.
AL-IME2-EXP SPECIFICATIONS
NETWORK RANGE
Gateway/Expander to Locks: Clear field range 500'.
Typical indoor range: Networx 75-175'; ArchiTech Networx:
50-125'. Note: Actual range varies with building con-
struction.
AL-IME2-EXP Expander
Installation Instructions
© ALARM LOCK 2018 WI2156BLF 1/18
Gateway/Expander to Expander: Clear field range 500'.
Typical indoor range, 75- 175'. Note: Actual range varies
with building construction.
AL RADIO LINK
900 MHz GFSK
50 Channels
10mW power output
POWER - Provided by UL Listed Class 2 Transformer
Peak Supply Current: 150mA
Input Voltage: 5 - 6VAC
Includes one (1) 6VAC External Power Supply
ENVIRONMENTAL
Operating Temperature: -20˚to 60˚C (-4˚to 140˚F)
Storage Temperature: -40˚to 85˚C (-40˚to 185˚F)
PHYSICAL
Enclosure Size: 4.5"H x 6.0"W x 1.94"D
Weight: 0.5lbs.
EXPANDER LOCATION GUIDELINES
Once your version 2 Gateway location has been selected,
the next step is to determine where to mount the Expander.
However, the following must be taken into consideration:
 Generally, the Expanders should be within approximately
75 feet (radially) from the Gateway or another Expander
 Expanders should be located within 100 feet (radially) from
the intended wireless lock locations
 Open areas will increase range while concrete building
construction, walls, ceilings and narrow corridors will
decrease range
 ArchiTech series locks generally have shorter range to/
from an Expander
 Select a location that allows access to the power wires
running from the 6VAC power transformer (supplied)
 Expanders should be mounted in elevated areas; however
mounting in a drop ceiling can adversely affect signal
strength
 Preferred mounting position = 6 to 12" below ceiling
 Expanders must be mounted vertically; horizontal "flat"
mounting of the Expander should be specifically avoided
 Although wood and wallboard construction can have little
effect upon signal strength, concrete or brick can reduce
signal strength by up to 35%. Steel-reinforced concrete or
metal lath and plaster can reduce signal strength as much
as 90%!
 Do NOT mount close to electrical wiring or other metal
obstructions such as pipes or conduits
 Installing in computer closets or server rooms can nega-
tively impact signal strength
Helpful Tips
 The AL-NSM Networx Signal Meter and the AL-NSG
Networx Signal Generator can assist with identifying
345 Bayview Avenue
Amityville, New York 11701
For Sales and Repairs 1-800-ALA-LOCK
For Technical Service 1-800-645-9440
or visit us at http://tech.napcosecurity.com/
(Note: Technical Service is for security professionals only)
Publicly traded on NASDAQ Symbol: NSSC

2
Blue and White ID Cards
We recommend that when installing any model Gateway, a
blue-colored "Gateway ID Card" (OI357) be completed,
and when installing the AL-IME2-EXP Expander, a white-
colored "Expander ID Card" (OI388) be completed.
Gateway and Expander physical locations may easily be for-
gotten. These ID cards may prove to be very useful when
replacing Gateways or Expanders, when using DL-Windows
to select a particular Gateway or Expander to discover locks,
or whenever an installed Gateway or Expander needs to be
physically located.
MOUNTING INSTRUCTIONS
The AL-IME2-EXP rear housing must be mounted "up" as
shown on the page 4 template; i.e. when the front housing is
attached, its engraved Networx logo must be located at the
lower right with the front housing positioned "up" in a conven-
tional manner. (The unit contains internal antennas that must
be positioned vertically). Horizontal "flat" mounting of the
enclosure is to be specifically avoided. As stated previously,
the AL-IME2-EXP Expander only requires connection to
the 6VAC power transformer wires.
Mount as follows:
1. Insert a small flat-head screwdriver into the slots at the
bottom and twist while applying inward pressure (see Fig.
1; insert the screwdriver closer to the edges of the unit, as
shown in the Fig. 1 "inset" image).
2. Using the rear housing as a mounting template, secure
optimal Gateway locations relative to Expanders and
locks. See WI2092 for complete information.
 The "SIGNAL LEVEL" graph displayed on the front
label of the AL-NSM Networx Signal Meter indi-
cates the signal strength as measured in "DL-
Windows units"; the AL-IME2-EXP will allow itself
to be connected to the Gateway (or another Expand-
er) if the signal is determined to be 37 or greater.
Therefore, the AL-NSM should have a signal
strength of 37 or above at the intended Expander
installation location
 We recommend obtaining or creating a layout of your
intended system identifying all proposed installation lo-
cations, also noting building construction materials
IMPORTANT: Be sure to read the " EXPANDER GROUP"
DIALS section on page 3 before powering your Expanders.
The above guidelines and tips should be followed for each
additional Expander added to the system. See next section
for Expander installation configurations.
INSTALLATION CONFIGURATIONS
AL-IME2-EXP Expanders can be added in any configura-
tion. Provided the above instructions from EXPANDER LO-
CATION GUIDELINES are followed, Gateways / Expanders
will automatically determine the optimal routing pathways
between one another, ensuring optimal signal levels. The
following are examples of Expand-
er configurations:
"Star Pattern": This configura-
tion could be used to cover an en-
tire building with a single version 2
Gateway located in the center, sur-
rounded by up to 7 Expanders
(maximum).
"Daisy-Chain": For covering long distances, such as a
long hallway, a "daisy-chain" configuration connects several
Expanders in series with a 100 foot maximum distance be-
tween the Gateway and the first (and between each subse-
quent) Expander. In this example, the signal is easily ex-
tended over 700 feet in one direction, and provides coverage
for door locks located along this range:
If a wireless lock along the above daisy-chain is unreacha-
ble, Expanders can be moved as required (in the example
below, Expanders E3, E5 and E6 were relocated to allow
the wireless signal to reach previously inaccessible locks).
The above are just 3 possible scenarios; in theory, endless
installation configurations are possible.
G E1 E2 E4 E7
E6E5
E3
G E3
E2
E6
E1
E4
E5
E7
G E1 E2 E3 E4 E5 E6 E7
Fig. 1: To separate rear housing from cover
(Inset: Insert flat-head screwdriver closer to the edges of the unit)
(Inset image)
Fig. 2: Rear housing mounting holes for single-gang (A) and
double-gang (B) electrical boxes, and four all-purpose holes (C)
A BB CC
A BB CC

3
the unit to a wall or other flat surface using the hardware
provided (see page 4 for printed template).
As shown in Fig. 2, the rear housing includes two mount-
ing holes for single-gang (A) and four mounting holes for
double-gang (B) electrical utility boxes, as well as four all-
purpose holes (C) for mounting to drywall or other surfac-
es (use minimum #6 screws suitable for the surface).
"EXPANDER GROUP" DIALS
Inside the Expander are 2 rotary dials (see Fig. 3). These
dials are used to set the "Expander Group". All version 2
Gateways include an identical set of dials. Therefore, the
dial values set on your Gateway MUST then match the dial
values set on your AL-IME2-EXP Expanders.
IMPORTANT: Each Gateway in your system MUST be
set to a different "Expander Group" value along with its asso-
ciated Expanders. The "Expander Group" dial setting deter-
mines which Expanders are associated with which Gateway,
thus preventing Gateways from discovering unintended Ex-
panders.
Expander Group values of "00" through "99" are valid selec-
tions.
IMPORTANT: The small " selection arrow" on each dial
must be pointing directly to the desired Group value. In Fig.
4 (below), the Group value is set to "50". Use a small flat-
head screwdriver to turn the dials and make the selections.
Be sure to orient the Expander as shown above with the RE-
SET button ABOVE the dials to ensure proper Group
setting!
POWER UP
Connect the 6VAC power transformer wires (non-polarized).
Upon power up:
●Red LED solid (momentarily)
●Yellow LED blinks (counting out "Expander Group" dial
setting).
Note: Zero = No blink
●Yellow LED solid + green LED flickering rapidly
Next, reset the Expander as follows:
Reset the Expander
IMPORTANT: Before securing the Expander housing
cover, ALWAYS reset the Expander memory, even if the
Expander is new "out of the box" and/or has never been
used previously.
After initial power up, press and hold the "RESET" button
(see below for location); continue to hold the button until the
red light turns on solid. Now, release the button and the
green light will flicker rapidly.
This "resetting" of the Expander clears all memory and en-
sures that any previous data is cleared from the unit.
Note: Resetting the Expander also re-writes the
"Expander Group" dial setting into the Expander memory.
EXPANDER LED INDICATIONS
CLOSE HOUSING COVER
Close the housing cover by first engaging the hooks at the
top, then snapping the bottom together. Secure the cover
with the Bottom Screw provided as shown in Fig. 5.
Congratulations! You're finished! Now go to the DL-
WINDOWS™ for Networx™ V5 USER'S GUIDE (OI383) for
instructions about discovering your Expanders from DL-
Windows.
Fig. 5: Bottom Screw
Fig. 3: "RESET" button and two "Expander Group dials"
Be sure to orient the Expander with the RESET button ABOVE
the dials as shown above to ensure proper Group setting !
RESET
button
Expander
Group
Dials
Yellow On Power up, displays "Expander Group" dial setting (in
two sequences)
Receiver On (normal operation)
Red Transmitter on
(Expander Status)
Not configured - Rapid blinking / flickering
Idle / configured - 1 blink per second
Lock Communication Fail - 2 blinks (continuously)
Expander Communication Fail - 4 blinks (continuously)
Green
Fig. 4. Example: The above Expander Group dials are set to "50"
"selection
arrow"
"selection
arrow"

4
ALARM LOCK SYSTEMS, INC. (ALARM LOCK) warrants its products to be free from manufacturing
defects in materials and workmanship for twenty four months following the date of manufacture. ALARM
LOCK will, within saidperiod, at its option, repair or replace any product failingto operate correctly without
chargeto theoriginal purchaseror user.
This warranty shall not apply to any equipment, or any part thereof, which has been repaired by others,
improperly installed, improperly used, abused, altered, damaged, subjected to acts of God, or on which
any serial numbers have been altered, defaced or removed. Sellerwill not be responsiblefor any disman-
tling or reinstallation charges, environmental wear and tear, normal maintenance expenses, or shipping
and freight expenses required to return products to ALARM LOCK. Additionally, this warranty shall not
coverscratches, abrasions ordeterioration duetothe useofpaints,solvents orother chemicals.
THEREARE NOWARRANTIES,EXPRESS ORIMPLIED,WHICH EXTENDBEYONDTHEDESCRIP-
TION ON THE FACE HEREOF. THERE ISNO EXPRESS OR IMPLIED WARRANTY OF MERCHANT-
ABILITY OR A WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE. ADDITIONALLY, THIS
WARRANTY IS IN LIEU OF ALL OTHER OBLIGATIONS OR LIABILITIES ON THE PART OF ALARM
LOCK.
Any action for breach of warranty, including but not limited to any implied warranty of merchantability,
mustbe broughtwithinthesixmonths following theend ofthe warrantyperiod.
IN NO CASE SHALL ALARM LOCK BE LIABLE TO ANYONE FOR ANY CONSEQUENTIAL OR
INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESS OR
IMPLIED,EVENIF THELOSS ORDAMAGEIS CAUSEDBY THESELLER'S OWNNEGLIGENCEOR
FAULT.
In case of defect, contact the security professional who installed and maintains your security system. In
order to exercise the warranty, the product must be returned by the security professional, shipping costs
prepaid and insured to ALARM LOCK. After repair or replacement, ALARM LOCK assumes the cost of
returning products under warranty. ALARM LOCK shall have no obligation under this warranty, or other-
wise, if the product has been repaired by others, improperly installed, improperly used, abused, altered,
damaged,subjected toaccident, nuisance, flood,fire oracts ofGod, oronwhichanyserial numbershave
been altered, defaced or removed. ALARM LOCK will not be responsiblefor any dismantling, reassembly
or reinstallation charges, environmental wear and tear, normal maintenance expenses, or shipping and
freight expenses required to return products to ALARM LOCK. Additionally, this warranty shall not cover
scratches,abrasions ordeteriorationdue tothe useof paints,solvents orother chemicals.
This warranty contains the entire warranty.It isthe solewarrantyandany prioragreements orrepresenta-
tions, whether oral or written, are either merged herein or are expressly cancelled. ALARM LOCK neither
assumes, nor authorizes any other person purporting to act on its behalf to modify, to change, or to
assumefor it,any otherwarranty orliability concerningitsproducts.
In no event shall ALARM LOCK be liable for an amount in excess of ALARM LOCK'soriginal selling price
of the product, for any loss or damage, whether direct, indirect, incidental, consequential, or otherwise
arising out of any failure of the product. Seller's warranty, as hereinabove set forth, shall not be enlarged,
diminished or affected by and no obligation or liability shall arise or grow out of Seller's rendering of
technicaladvice orservice inconnectionwith Buyer'sorder ofthegoodsfurnishedhereunder.
ALARMLOCK RECOMMENDSTHAT THEENTIRESYSTEM BECOMPLETELYTESTED WEEKLY.
Warning: Despite frequent testing, and due to, but not limited to, any or all of the following; criminal
tampering, electrical or communications disruption, it is possible for the system to fail to perform as ex-
pected. ALARM LOCK does not represent that the product/system may not be compromised or circum-
vented;or thatthe productor systemwill preventany personalinjuryorproperty lossby burglary,robbery,
fire or otherwise; nor that the product or system will in all cases provide adequate warning or protection. A
properly installed and maintained alarm may only reduce risk of burglary, robbery, fire or otherwise but it
is not insurance or a guarantee that these events will not occur. CONSEQUENTLY, SELLER SHALL
HAVE NO LIABILITY FOR ANY PERSONAL INJURY, PROPERTY DAMAGE, OR OTHER LOSS
BASED ON A CLAIM THE PRODUCT FAILED TO GIVE WARNING. Therefore, the installer should in
turn advise the consumer to take any and all precautions for his or her safety including, but not limited to,
fleeing thepremises and calling police or fire department, in orderto mitigate the possibilities of harm and/
ordamage.
ALARM LOCK is not an insurer of either the property or safety of the user's family or employees, and
limits its liability for any loss or damageincluding incidental or consequential damages to ALARM LOCK's
originalselling priceof theproduct regardlessof thecause ofsuchlossor damage.
Some states do not allow limitations on how long an implied warranty lasts or do not allow the exclusion
or limitation of incidental or consequential damages, or differentiate in their treatment of limitations of
liability for ordinary or gross negligence, so the above limitations or exclusions may not apply to you. This
Warrantygives youspecific legalrightsand youmay alsohave otherrightswhich varyfrom stateto state.
ALARM LOCK LIMITED WARRANTY
AL-IME2-POE and AL-IME2-EXP Mounting Template
1-13/16"
3-3/8"
3-9/32"
4"