Albion TCT 35 Guide

OPERATING MANUAL AND USER GUIDE
!"!#$%
www.albionamps.com
TCT 35.indd 1 2011-5-11 14:15:15

TCT 35.indd 2 2011-5-11 14:15:15

Contents
Important Safety Instructions ...................................................................................... 1
Important Warnings ....................................................................................................... 2
Designer's Introduction................................................................................................. 3
2XWOLQH6SHFL¿FDWLRQ ..................................................................................................... 4
TCT 35 Features and Controls ..................................................................................... 5
Rear Panel....................................................................................................................... 6
6SHFL¿FDWLRQ................................................................................................................... 7
TCT 35.indd 3 2011-5-11 14:15:15

OPERATING MANUAL AND USER GUIDE
Important Safety Instructions
1. Read these instructions – All the safety and operating
instructions should be read before this product is
operated.
2. Keep these instructions – The safety and operating
instructions should be retained for future reference.
3. Heed all warnings – All warnings on the appliance
and in the operating instructions should be adhered
to.
4. Follow all instructions – All operating and use
instructions should be followed.
5. Do not use this apparatus near water – The appliance
should not be used near water or moisture – for
example, in a wet basement or near a swimming pool
etc.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in
accordance with the instructions.
8. Do not install near any heat sources such as
radiators, heat registers, stoves, or other apparatus
LQFOXGLQJDPSOL¿HUVWKDWSURGXFHKHDW
9. Do not defeat the safety purpose of the polarized or
grounding plug. A polarized plug has two blades with
one wider than the other. A grounding plug has two
blades and a third grounding prong. The wide blade
or the third prong is provided for your safety. If the
SURYLGHGSOXJGRHVQRW¿WLQWR\RXURXWOHWFRQVXOWDQ
electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or
pinched particularly at the plugs, convenience
receptacles, and at the point where they exit from the
apparatus.
11. Only use attachments/accessories specified by the
manufacturer.
12. Use only with the cart, stand, tripod, bracket or
WDEOHVSHFL¿HGE\WKHPDQXIDFWXUHURU VROGZLWKWKH
apparatus. When a cart or rack is used, use caution
when moving the cart/ apparatus combination to
avoid injury from tip-over.
13. Unplug the apparatus during lightning storms or when
unused for long periods of time.
5HIHUDOOVHUYLFLQJWRTXDOL¿HGSHUVRQQHO6HUYLFLQJLV
required when the apparatus has been damaged in
any way including: power supply cord or plug damage,
liquid spillages, objects falling into the unit, exposure
to rain/moisture or impact damage.
15. Please keep the unit in a well ventilated environment.
16. CAUTION: These servicing instructions are for use
by qualified service personnel only. To reduce the
risk of electric shock, do not perform any servicing
other than that contained in the operating instructions
XQOHVV\RXDUHTXDOL¿HGWRGRVR
:$51,1*7RUHGXFHWKHULVNRI¿UHRUHOHFWULFVKRFN
do not expose this apparatus to rain, moisture and
dripping or splashing of liquids. Containers filled
with liquids such as vases or drinks should never be
placed on top of or near the unit.
18. WARNING: The mains plug/appliance coupler is used
as disconnect device, the disconnect device shall
remain readily operable.
7KHOLJKWQLQJÀDVK ZLWK DUURZKHDGV\PEROLVWRDOHUW
the user to the presence of non-insulated "dangerous
voltage" within the product's enclosure that may be
RIVXI¿FLHQWPDJQLWXGHWRFRQVWLWXWH DULVNRIHOHFWULF
shock.
-Warning: To reduce the risk of electric shock, do
QRWUHPRYHFRYHURUEDFNDVWKHUHDUHQRXVHU
VHUYLFHDEOHSDUWVLQVLGH 5HIHU VHUYLFLQJ WRTXDOL¿HG
personnel.
1
TCT 35.indd 4 2011-5-11 14:15:15

series
- The exclamation point within an equilateral triangle
is intended to alert the user to the presence of
important operating and maintenance instructions in
the literature accompanying the appliance.
20. Protective earthing terminal. The apparatus
should be connected to a mains socket outlet with a
protective earthing connection.
21. Correct Disposal of this product. This marking
indicates that this product should not be disposed
with other household wastes throughout the EU. To
prevent possible harm to the environment or human
health from uncontrolled waste disposal, recycle
it responsibly to promote the sustainable reuse of
material resources. To return your used device,
please use the return and collection systems or
contact the retailer where the product was purchased.
They can take this product for environmentally safe
recycling.
22. WARNING: The terminals marked with the symbol of
“ ” may be of sufficient magnitude to constitute a
risk of electric shock. The external wiring connected
to the terminals requires installation by an instructed
person or the use of ready-made leads or cords
according to manufacturer’s instruction.
³&ODVV :LULQJ³IRU DOORWKHU7(50,1$/6 SURYLGHG
the audio output power exceeds 10W per channel
under normal operating conditions or the apparatus is
LQWHQGHG WREHLQVWDOOHGRULQWHUFRQQHFWHG LQWKH¿HOG
E\D6.,//('3(5621
Important Warnings
$/:$<6 UHDG WKH PDQXDO RI \RXU QHZ DPSOLILHU ±
HYHQLI\RXDUHH[SHULHQFHGZLWKJXLWDUDPSOL¿HUVDQG
their technology! There could be something important
that you need to know.
$/:$<6FKHFNWKDW\RXUQHZDPSOL¿HULVVXLWHGWRWKH
mains power supply in your country.
1(9(5 GLVFRQQHFW WKH HDU WK JURXQG FRQQHFWLRQ
from your amplifier. It is there to prevent you from
receiving a fatal electric shock!
NEVER use your amplifier equipment in a high
PRLVWXUHHQYLURQPHQWVXFKDVUDLQRU DOORZLW WR JHW
wet.
$/:$<6 XVHFRUUHFWDQGZHOO PDLQWDLQHGFDEOHVIRU
all inter-connections whether for power, speaker or
signal connections. If in any doubt, get them checked
or renew immediately.
1(9(5XVH\RXUDPSOL¿HU SURGXFWVZLWKDQ\ FRROLQJ
vents covered, even partially. Your amp loves being
fed nice cool air!
3$57,&8/$5/< ZLWK YDOYH WXEH DPSV DOORZ \RXU
amp to warm up before playing, 5 minutes is a
good length of time. Also allow your amp to have a
good cool down after playing and before moving it,
especially into the back of a car on a cold winter’s
night! Your valves will last longer if you give them a
little respect and TLC. Valves are pretty tough when
you think of what they are made from – but can be
very fragile if treated with physical abuse.
$/:$<6XVHDFDEOHUDWHGIRUORXGVSHDNHUFRQQHFWLRQ
XVHIRUFRQQHFWLQJ\RXUDPSOL¿HUWR\RXUORXGVSHDNHU
system. DO NOT use a screened guitar cable for
speaker use.
NEVER use your amplifier without it connected to a
suitable matched loudspeaker system.
:$51,1* 6RPHWLPHVSDUWV RI WKHRXWVLGH RI\RXU
DPSOL¿HUPD\JHWKRWWRWKHWRXFK7KLVLVTXLWHQRUPDO
and will be within safe operational limits. These
limits are set by various countries safety approvals
committees, and we at Albion Musical Instruments
design, build, test, and have approved our products to
WKHVH LQWHUQDWLRQDO VWDQGDUGV ,H&( 8/&6$&%
ETL etc.
EMC INTERFERENCE. Even though all Albion
Musical Instruments products are designed and
tested to international electro-magnetic interference
standards, please note that cellular phones in close
proximity may cause some interference with your
DPSOL¿HU
$/:$<6KDYH\RXUDPSOL¿HUVHUYLFHGE\DWHFKQLFLDQ
qualified in servicing musical instrument amplifier
products. If in doubt please contact your dealer.
2
TCT 35.indd 5 2011-5-11 14:15:16

OPERATING MANUAL AND USER GUIDE
Designer's Introduction
When I sat down with a blank piece of paper (well actually
DVWKLV LV WKHVW FHQWXU\DEODQNFRPSXWHUVFUHHQWR
GHVLJQWKH7&7UDQJHRIDPSOL¿HUV,KDGDORQJKDUGORRN
at all the guitar amps that I had designed previously. Even
though many of those designs were destined to be what
can only be called Classics, I wanted to approach these
new amps in a different perspective. Instead of designing
under the corporate image of whatever company I was
working for at the time, the TCT amps were for the first
time “my” amps. This put the image in my mind as “what
do I want from an amp, and how do I want it to look”. As
a guitar player of many years I have used many different
amps, many times different ones hooked up in a multi-
amp set up for the different sounds that I needed at the
time. This realisation formulated the basic concept and
functionality of the direction I needed to go in, something
that was simple to use but was as variable as possible.
Oh, and sounded great at everything it did as well!
The “what do I want it to look like” actually developed
pretty quickly – I wanted something that looked classy
and stood out from the crowd, something that at the same
time was familiar yet unique. For want of a better word
“boutique”.
,WKLQNWKDWWKH7&7VHULHVRI$OELRQDPSVIXO¿OVP\GUHDP
and desire with room to spare. Finally “my” amp!
I personally love playing these amps and can sit there
playing them for hours on end without tiring of them –
sometimes to the annoyance of my small team I have to
add – I do tend to play very loud at times, and they do
have to work!!
I hope that you get as much playing pleasure out of your
TCT amp as I do.
Thank you
2XWOLQH6SHFLÀFDWLRQ
7KH7&7+KHDGDQG7&7&[´FRPERXWLOLVH
WKHVDPHDPSOL¿HU FKDVVLV7KHDPSOL¿HUKDVVHSDUDWH
switchable channels, both featuring the same controls per
channel. Channel A features the EQ circuit before the gain
VWDJHV ZKLOVW &KDQQHO %IHDWXUHV WKH(4 DIWHU WKHJDLQ
stages.
%RWKFKDQQHOVIHDWXUHWKHFDSDELOLW\RIUXQQLQJGHSHQGLQJ
RQFRQWUROVHWWLQJVIURP³FOHDQ´WKURXJK³FUXQFK´WR³KLJK
JDLQ OHDG´ %XW GXH WR WKH GLIIHUHQW ³YRLFLQJ´ SURYLGHG
E\ WKH (4 SRVLWLRQ DQG RWKHU YRLFLQJ HOHPHQWV ERWK
channels have an entirely different spectral response and
player’s “feel”.
The player himself can choose which he prefers for his
particular style and suitability.
7KHUHLVQR¿[HG&OHDQ RU/HDGFKDQQHO WKDWFDQEHWKH
limiting factor on other makes of multi channel guitar
amplifiers. This flexibility sets the Albion TCT guitar
DPSOL¿HUVDSDUWIURPRWKHUEUDQGV
The TCT35 amplifier circuit utilizes a combination of
technologies to provide optimum performance required for
high class consistent playing night after night.
The preamplifier section uses 3 double triode low noise
$ ;(&& YDOYHV WXEHV ZLWK KLJK VSHHG
relay switching for circuit reconfiguration when channel
switching.
The input gain itself is a very special proprietary circuit
combining a 12AX7 preamp valve and a unique high
YROWDJH)(7¿HOGHIIHFWWUDQVLVWRU7KLVFLUFXLWKDVPDQ\
benefits that are not readily available with tube only
designs, in that the input stage noise (particularly heater
KXPLVJUHDWO\UHGXFHG¿UVWVWDJHPLFURSKRQ\LVYDVWO\
reduced, input stage gain and drive capability is increased
allowing it to drive the rest of the preamp better, and
lastly it imparts a tonality approaching that of a pentode
tube, which is good in its own right! All this means is that
the input stage will perform better and more reliably by
reducing the things you DON’T want from a tube!
A word about the EQ system used on the Albion TCT
range of amps. Although the tone controls are based on
the time honoured interactive passive system historically
used on most guitar amps, our design is somewhat wider
ranging than most others. For instance the MIDDLE
control has a much wider range than normal and will give
a substantial amount of mid boost as well as mid cut.
The result of this opens up a whole new range of sound
possibilities that we think you will enjoy. For instance using
the mid boost capability gives rise to some very sweet
3
TCT 35.indd 6 2011-5-11 14:15:17

series
singing sustain – great for blues and fusion.
7KHSUHDPSOL¿HU¶VWZLQ FKDQQHORXWSXWLVWKHQ PL[HGLQWR
the FX loop and digital Reverb system. This section is
unashamedly solid state as this section is designed to be
as transparent as possible in passing all the valve tone
RIWKHSUHDPSWR WKHLQSXWRIWKHDOOWXEHSRZHU DPSOL¿HU
section, whilst handling the duties of efficient real world
FX loop connection, digital reverb connection, and noise
free seamless channel switching.
7KH7&7SRZHUDPSOL¿HUXVHVD$;(&&SKDVH
splitter and 2 off 6L6 output valves. The 35 watt output
power from this configuration allows the output valves
to be run at a hotter class of operation for a smooth and
warm tone without losing any of the classic 6L6 sound.
The power amp section can be switched between two
feedback networks – open loop & closed loop. Open loop
gives a raw, open, vintage style to the sound with lots of
player feel and tactile response. Closed loop gives a much
tighter modern response to the sound and feel.
The output section can also be run at 33% (approx 12
ZDWWVRILWVWRWDO RXWSXWSRZHU IRUWKRVHVLWXDWLRQVZKHQ
ÀDWRXWUHDOO\LV³WRRORXG´
The TCT35C combo comes complete with one of our
own designed and built Albion G1270C 16ohm 12”
loudspeakers.
4
TCT 35.indd 7 2011-5-11 14:15:17

TCT 35 Features and Controls
INPUT –Mono !” Jack socket for instrument input. Use a
properly screened “guitar” cable for interconnection. There
are many different makes of guitar cable available, ranging
from fairly inexpensive to very expensive. Each have
different characteristics, and depending on your particular
guitar will give different results, all very confusing for
the inexperienced! For instance, a “cheap” cable with
high capacitance (which would normally be termed as a
³QRW YHU\ JRRG FDEOH´ FDQDFWXDOO\ EH RI EHQHILW IRU DQ
overly bright single coil guitar by taming the very high end
frequencies. Alternatively, a very low capacitance cable
can help brighten up a muddy sounding hum-bucker type
guitar. If possible experiment to try and find what suits
you and your guitar best. Hopefully your dealer can help
you choose the right cable. If using an FX pedal system
then the best advice is to use high quality, low noise, low
capacitance cable from pedals to amp connection.
CHANNEL SWITCHING – the pushbutton above the
INPUT JACK controls which channel you are using. OUT
activates channel A and illuminates A l.e.d. indicator, and
,1VZLWFKHV RYHU WR FKDQQHO %DQG WKH% OHGLQGLFDWRU
will come on. When using the remote footswitch operation
WKHQ WKLVSXVKVZLWFK 0867EHSXVKHGLQWRHQJDJH WKH
footswitch circuit.
CHANNEL A & B PREAMP CONTROLS – each
channel has the same independent control line up,
therefore the description below should be read for each
channel.
GAIN – this control determines the amount of signal that
WKH¿UVWDPSOL¿HUJDLQVWDJHOHWVWKURXJKWRWKHUHVWRIWKH
DPSOL¿HU$OWKRXJKWKLVFRQWUROZRUNVLQ FRQMXQFWLRQZLWK
the next DRIVE control, it is pretty straightforward in use
– low settings are clean – mid settings are in the start
of distortion range – and high settings are the overdrive
range.
DRIVE –the DRIVE control determines the gain and
voicing of the 2nd and 3rd amplification stages. Please
be aware that this control does NOT turn the signal OFF
at zero setting! As with the GAIN control, low settings are
cleaner – mid settings are crunchier – and high settings
are more distorted.
As stated above the GAIN and DRIVE controls work in
conjunction and by so doing a very wide of different gain
levels and voicing’s can be obtained – much more than
amps with just a single gain control. Please experiment;
there is no right or wrong setting, but many different
sounds and voicings
TREBLE, MIDDLE, BASS EQ –as stated above
the EQ system is very wide ranging and very versatile,
experimentation is the key – please start with these
controls set to mid position. What is important to
remember is that the EQ circuit is connected before the
gain circuits on channel A, and after the gain circuits on
FKDQQHO%3XWWLQJWKLVDVVLPSO\DVSRVVLEOHWKLVPHDQV
that channel A’s EQ affects the sound of the guitar signal
JRLQJLQWRWKHSUHDPSJDLQFLUFXLWVZKHUHDVFKDQQHO%¶
s EQ affects the sound generated by the preamp gain
FLUFXLWV7KLQN RI LWDVFKDQQHO$KDV DZHVWFRDVW86$
ÀDYRXUDQGFKDQQHO%KDVPXFKPRUHRID%ULWLVKÀDYRXU
– but with much more on offer.
VOLUME – this quite simply controls the output of each
channels preamp, giving you the required sound level and
balance that you require.
RESPONSE – the two controls under this legend are
PDUNHG('*(DQG)¶%.7KH('*(URWDU\FRQWUROFDQEH
treated very much like the presence control on other guitar
amps, but with a difference – instead of just boosting
high frequencies in the power amplifier, the EDGE
control also reduces the high frequencies when turned
GRZQ JLYLQJ DPXFK VPRRWKHUVZHHWHUWRQH 7KH )¶%.
VZLWFKVWDQGVIRU)(('%$&. DQGLW JLYHV WZR GLIIHULQJ
³IHHGEDFNORRSV´DURXQGWKHSRZHUDPSOL¿HUFLUFXLW,QWKH
case of the TCT35 this is “TIGHT” (closed loop, switch
RXWDQG ³/226(´ RSHQORRS VZLWFK LQ1RWWRJHW WRR
WHFKQLFDOWKHVHWZRVHWWLQJVFDQHLWKHUJLYHDÀDWWHUWLJKWO\
controlled response between the power amplifier and
5
SERIES EFFECTS LOOP
LEVELRETURN SEND
BYPASSLOOP
ROUTE
LOW HIGH
LOUDSPEAKER OUTPUT SOCKETS
PARALLEL CONNECTED SOCKETS - INTERNAL LOUDSPEAKER = 16ohms
WARNING! DO NOT USE WITHOUT CONNECTING
LOUDSPEAKER LOAD TO AMPLIFIER AND MATCHING
OUTPUT IMPEDANCE TO SPEAKER IMPEDANCE.
16ohm OUT = 1 x 16ohm LS, 8ohm OUT = 1 x 8ohm OR 2 x 16ohm LS
OUTPUT = 35 Watts RMS into 8 or 16 ohms
DO NOT CONNECT ANY UNBALANCED GROUND CONNECTED EQUIPMENT
TO THE OUTPUT OF THIS AMPLIFIER. USE UN-GROUNDED DIFFERENTIAL
MODE ONLY. IF IN DOUBT REFER TO USER MANUAL
35 WATT TWIN CHANNEL VALVE GUITAR AMPLIFIER
FOOTSWITCH
CONNECTOR
8ohm
16ohm
HT FUSE
MAINS INPUT
T315mAL 250VT1.6AL 250V
WARNING! USE CORRECT FUSE ONLY
POWER MUTE 100% PHASE +
ACTIVE 33% PHASE -
MAINS
ON POWER OUTPUT
MASTER REVERB
OUTPUT MIX F'BK
POWER AMP RESPONSE
DEEP EDGE
MIX LOWER
1
2
3
46
7
8
9
MIX HIGHER 0
1
2
3
46
7
8
9
10 0
1
2
3
456
7
8
9
10 0
1
2
3
456
7
8
9
10 0
1
2
3
456
7
8
9
10 0
1
2
3
456
7
8
9
10 0
1
2
3
456
7
8
9
10 0
1
2
3
456
7
8
9
10 0
1
2
3
456
7
8
9
10 0
1
2
3
456
7
8
9
10
0
1
2
3
456
7
8
9
10 0
1
2
3
456
7
8
9
10 0
1
2
3
456
7
8
9
10 0
1
2
3
456
7
8
9
10 0
1
2
3
456
7
8
9
10 0
1
2
3
456
7
8
9
10
VOLUME TREBLE MIDDLE BASS DRIVE GAIN
TIGHT
SMOOTH
SHIFT
TIGHT
LOOSE
INPUT
CHANNEL A - PRE EQ
CHANNEL B - POST EQ
A-B MIX
PRESS BOTH
FOR REMOTE
OPERATION
0
1
2
3
456
7
8
9
10
55
A-B/MIX
BALANCE
SERIES EFFECTS LOOP
LEVELRETURNSEND
BYPASS LOOP
ROUTE
LOW HIGH
LOUDSPEAKER OUTPUT SOCKETS
PARALLEL CONNECTED SOCKETS
WARNING! DO NOT USE WITHOUT CONNECTING
LOUDSPEAKER LOAD TO AMPLIFIER AND MATCHING
OUTPUT IMPEDANCE TO SPEAKER IMPEDANCE.
16ohm OUT = 1 x 16ohm LS, 8ohm OUT = 1 x 8ohm OR 2 x 16ohm LS
OUTPUT = 100 Watts RMS into 8 or 16 ohms
DO NOT CONNECT ANY UNBALANCED GROUND CONNECTED EQUIPMENT
TO THE OUTPUT OF THIS AMPLIFIER. USE UN-GROUNDED DIFFERENTIAL
MODE ONLY. IF IN DOUBT REFER TOUSER MANUAL
100 WATT TWIN CHANNEL VALVE GUITAR AMPLIFIER
FOOTSWITCH
CONNECTOR
OUTPUT BIAS ADJUST SYSTEM
WARNING! DO NOT REMOVE COVER
8ohm
16ohm
HT FUSE MAINS INPUT
T1AL 250V T2.5AL 250V
WARNING! USE CORRECT FUSE ONLY
CAUTION! NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED TECHNICIAN
SERIES EFFECTS LOOP
LEVELRETURN SEND
BYPASSLOOP
ROUTE
LOW HIGH
LOUDSPEAKER OUTPUT SOCKETS
PARALLEL CONNECTED SOCKETS
WARNING! DO NOT USE WITHOUT CONNECTING
LOUDSPEAKER LOAD TO AMPLIFIER
OUTPUT = 200 Watts RMS into 8ohms - 300 Watts RMS into 4ohms
DO NOT CONNECT ANY UNBALANCED GROUND CONNECTED EQUIPMENT
TO THE OUTPUT OF THIS AMPLIFIER. USE UN-GROUNDED DIFFERENTIAL
MODE ONLY. IF IN DOUBT REFER TO USER MANUAL
MAINS INPUT T3.15AL 250V
WARNING! USE CORRECT FUSE ONLY
TUNER
FOOTSWITCH
MUTE OUT
LINE OUT
GROUND
CONNECT
ISOLATE
300Watt TUBE PRE/BIPOLAR POWER BASS AMPLFIER
WARNING! DO NOT USE LOAD OF LESS THAN 4ohm IMPEDANCE
OPERATING MANUAL AND USER GUIDE
8
TCT 35.indd 8 2011-5-11 14:15:38

the loudspeaker system, great for cleaner sounds and
IDVWSLFNLQJ WHFKQLTXHVFORVHGORRSRULQWKHRSHQORRS
position, the response is a lot looser and gutsier, great for
Rock!
REVERB MIX – quite simply the amount of in-built
Reverb that is Mixed with the dry signal. The Reverb can
be turned On/Off with the supplied footswitch.
MASTER OUTPUT – This volume control is placed
between the whole preamp section and the input to the
power amp section. Once your channel balance is set
up, then this control is used to set up the required playing
volume from the TCT35.
POWER AMP SWITCHING – 100%/33% switch allows
the clipping level coming out of the poweramp/speaker
set up can be reduced to 33% of full power (approx. 12
:DWWV DOORZLQJ JUHDW ORZ YROXPHSHUIRUPDQFH ZLWKRXW
compromise. Coupled with the Master Output control,
great tone can be achieved even at “whisper” levels.
7KH087($&7,9(VZLWFKLVSULPDULO\D 6WDQGE\VZLWFK
IRXQGRQWKH PDMRULW\RIJXLWDU DPSOL¿HUV ±WKHH[FHSWLRQ
being is that we have termed it Mute and Active because
it has a much better meaning. Mute is amplifier off, and
$FWLYHLVDPSOL¿HUZRUNLQJ
7KH 0$,1632:(5VZLWFKLVVHOIH[SODQDWRU\LQWKDW LW
WXUQVWKHPDLQVSRZHUVXSSO\FRPLQJLQWRWKHDPSOL¿HURII
RURQ
Rear Panel
SERIES EFFECTS LOOP – WKLVFRQVLVWVRIWKH6HQG
and Return jack sockets, Level switch and Route switch.
7KH 6HQG VRFNHWVXSSOLHV WKH SUHDPS RXWSXW FKDQQHO
$DQGFKDQQHO%VLJQDOWRIHHG WKHLQSXWRI\RXUUHPRWH
effects system, whilst the Return socket connects the
RXWSXWRI\RXUHIIHFWVEDFNLQWRWKHDPSOL¿HUFLUFXLW3OHDVH
remember that the loop is of the “series” type, so that the
entire signal is sent and returned back to the amplifier.
The Level switch has Low and High settings, the setting
of this will be determined by the performance quality of
\RXUHIIHFWVV\VWHPDQGDOVRKRZORXGWKH7&7DPSOL¿HU
LVVHW/RZLVQRPLQDOO\DORRSOHYHORIG%9DQG+LJKLV
nominally 0dbV. Experiment with the Level switch to see
what suits your system best.
Effects Loops in general are designed to work with rack
type processors rather than floor stomp boxes. The
reason for this is that most floor pedals do not have
enough headroom to let the signal pass through without
causing the signal to distort unduly. Also loops are
designed for unity-gain systems (i.e. what goes in, comes
EDFNRXWDWWKHVDPHDPRXQWRIJDLQDQGVLJQDOOHYHODQG
are best suited for time based processors like chorusing
and delays, graphic EQ, and studio type compressors.
'H¿QLWHO\GRQRWSXWJDLQW\SHSHGDOVGLVWRUWLRQRYHUGULYH
HWFLQWKHORRS±LWUHDOO\ZLOOQRWVRXQGJRRGDQGEHYHU\
YHU\QRLV\,I\RXKDYHDJRRGÀRRU W\SHSURFHVVRUWKHQ
by all means experiment for your time delay type effects –
use the low level – it may work, it may not!
7KH5287(VZLWFKZKHQVHWWR%\SDVVGLVDEOHVWKH/RRS
circuit if not being used, which is best practise if not using
the effects loop.
FOOTSWITCH CONNECTOR – the supplied Albion
2-button footswitch connects into this socket for Channel
$% VZLWFKLQJ DQG 5HYHUE 2Q2II IXQFWLRQV 3OHDVH
UHPHPEHUWKDW WKHIURQWSDQHO FKDQQHO VZLWFK 0867 EH
pushed in for the remote foot-switching to work.
LOUDSPEAKER OUTPUTS – the two output jack
sockets are parallel wired, so please take this into
consideration when using multi speaker connections. The
DFFRPSDQ\LQJ2XWSXW,PSHGDQFH6HOHFWRUDOORZVWKHXVH
of full power connection into either 8 or 16 ohm speaker
systems. I.e. 16 ohm output = 1 x 16 ohm speaker -- 8
ohm output = 1 x 8 ohm speaker OR 2 x 16 ohm speaker.
Warning! The use of any other impedance may cause
GDPDJHWR\RXUDPSOL¿HU
7KH 6HOHFWRU VZLWFK LV UHFHVVHG WR SUHYHQW XQNQRZQ
accidental switching of the set impedance – to adjust
SOHDVHXVHD ÀDWVFUHZGULYHUEODGHLQWKHVHOHFWRUVZLWFK
paddle slot.
6
SERIES EFFECTS LOOP
LEVELRETURN SEND
BYPASSLOOP
ROUTE
LOW HIGH
LOUDSPEAKER OUTPUT SOCKETS
PARALLEL CONNECTED SOCKETS - INTERNAL LOUDSPEAKER = 16ohms
WARNING! DO NOT USE WITHOUT CONNECTING
LOUDSPEAKER LOAD TO AMPLIFIER AND MATCHING
OUTPUT IMPEDANCE TO SPEAKER IMPEDANCE.
16ohm OUT = 1 x 16ohm LS, 8ohm OUT = 1 x 8ohm OR 2 x 16ohm LS
OUTPUT = 35 Watts RMS into 8 or 16 ohms
DO NOT CONNECT ANY UNBALANCED GROUND CONNECTED EQUIPMENT
TO THE OUTPUT OF THIS AMPLIFIER. USE UN-GROUNDED DIFFERENTIAL
MODE ONLY. IF IN DOUBT REFER TO USER MANUAL
35 WATT TWIN CHANNEL VALVE GUITAR AMPLIFIER
FOOTSWITCH
CONNECTOR
8ohm
16ohm
HT FUSE
MAINS INPUT
T315mAL 250VT1.6AL 250V
WARNING! USE CORRECT FUSE ONLY
POWER MUTE 100% PHASE +
ACTIVE 33% PHASE -
MAINS
ON POWER OUTPUT
MASTER REVERB
OUTPUT MIX F'BK
POWER AMP RESPONSE
DEEP EDGE
MIX LOWER
1
2
3
46
7
8
9
MIX HIGHER 0
1
2
3
46
7
8
9
10 0
1
2
3
456
7
8
9
10 0
1
2
3
456
7
8
9
10 0
1
2
3
456
7
8
9
10 0
1
2
3
456
7
8
9
10 0
1
2
3
456
7
8
9
10 0
1
2
3
456
7
8
9
10 0
1
2
3
456
7
8
9
10 0
1
2
3
456
7
8
9
10
0
1
2
3
456
7
8
9
10 0
1
2
3
456
7
8
9
10 0
1
2
3
456
7
8
9
10 0
1
2
3
456
7
8
9
10 0
1
2
3
456
7
8
9
10 0
1
2
3
456
7
8
9
10
VOLUME TREBLE MIDDLE BASS DRIVE GAIN
TIGHT
SMOOTH
SHIFT
TIGHT
LOOSE
INPUT
CHANNEL A - PRE EQ
CHANNEL B - POST EQ
A-B MIX
PRESS BOTH
FOR REMOTE
OPERATION
0
1
2
3
456
7
8
9
10
55
A-B/MIX
BALANCE
SERIES EFFECTS LOOP
LEVELRETURNSEND
BYPASS LOOP
ROUTE
LOW HIGH
LOUDSPEAKER OUTPUT SOCKETS
PARALLEL CONNECTED SOCKETS
WARNING! DO NOT USE WITHOUT CONNECTING
LOUDSPEAKER LOAD TO AMPLIFIER AND MATCHING
OUTPUT IMPEDANCE TO SPEAKER IMPEDANCE.
16ohm OUT = 1 x 16ohm LS, 8ohm OUT = 1 x 8ohm OR 2 x 16ohm LS
OUTPUT = 100 Watts RMS into 8 or 16 ohms
DO NOT CONNECT ANY UNBALANCED GROUND CONNECTED EQUIPMENT
TO THE OUTPUT OF THIS AMPLIFIER. USE UN-GROUNDED DIFFERENTIAL
MODE ONLY. IF IN DOUBT REFER TO USER MANUAL
100 WATT TWIN CHANNEL VALVE GUITAR AMPLIFIER
FOOTSWITCH
CONNECTOR
OUTPUT BIAS ADJUST SYSTEM
WARNING! DO NOT REMOVE COVER
8ohm
16ohm
HT FUSE MAINS INPUT
T1AL 250V T2.5AL 250V
WARNING! USE CORRECT FUSE ONLY
CAUTION! NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED TECHNICIAN
SERIES EFFECTS LOOP
LEVELRETURN SEND
BYPASSLOOP
ROUTE
LOW HIGH
LOUDSPEAKER OUTPUT SOCKETS
PARALLEL CONNECTED SOCKETS
WARNING! DO NOT USE WITHOUT CONNECTING
LOUDSPEAKER LOAD TO AMPLIFIER
OUTPUT = 200 Watts RMS into 8ohms - 300 Watts RMS into 4ohms
DO NOT CONNECT ANY UNBALANCED GROUND CONNECTED EQUIPMENT
TO THE OUTPUT OF THIS AMPLIFIER. USE UN-GROUNDED DIFFERENTIAL
MODE ONLY. IF IN DOUBT REFER TO USER MANUAL
MAINS INPUT T3.15AL 250V
WARNING! USE CORRECT FUSE ONLY
TUNER
FOOTSWITCH
MUTE OUT
LINE OUT
GROUND
CONNECT
ISOLATE
300Watt TUBE PRE/BIPOLAR POWER BASS AMPLFIER
WARNING! DO NOT USE LOAD OF LESS THAN 4ohm IMPEDANCE
series
TCT 35.indd 9 2011-5-11 14:15:58

OPERATING MANUAL AND USER GUIDE
6SHFL¿FDWLRQ
ZDWWV506RXWSXWLQWRRURKPLPSHGDQFH
loudspeaker load.
4 off 7025/12AX7/ECC83 double triode small signal valves
WXEHV
RII/*&SRZHUYDOYHVWXEHV
CAUTION!
There are no user serviceable parts mounted
LQVLGH\RXUDPSOL¿HU5HIHUVHUYLFLQJWRVXLWDEO\
TXDOL¿HGSHUVRQQHO
This means that for your own safety and the
correct performance of your amplifier, do not
open the chassis unless you really do know what
you are doing!
The TCT35C 1 x 12” combo is fitted with a 16 ohm
loudspeaker. Most Albion guitar loudspeaker cabinets are
also 16 ohm.
HT FUSE – WKLVIXVHSURWHFWV\RXUDPSOL¿HUIURPIXUWKHU
damage in the case of one of the 6L6 output valves having
a failure.
WARNING! USE THE CORRECT REPLACEMENT
VALUE ONLY!
Using a wrong value can cause expensive damage to your
DPSOL¿HU
MAINS INPUT – the mains input receptacle allows for
the connection of the mains power cord, and also houses
WKHPDLQVSRZHUIXVH7RFRPSO\ZLWK,QWHUQDWLRQDO6DIHW\
5HJXODWLRQVIRU\RXUVDIHW\DQGSURWHFWLRQ\RXUDPSOL¿HU
is supplied to work with the mains supply in your country.
Please check the white rating label fitted to the back
panel. If in any doubt, please check with your supplier. It is
of utmost importance to use the correct earthed and rated
SRZHUFRUGDVLVVXSSOLHGZLWK\RXUDPSOL¿HU:$51,1*
DO NOT USE WITHOUT CONNECTING THE
EARTH (GROUND) WIRE.
In the case of the mains fuse blowing, this can be changed
E\UHPRYLQJWKHSRZHUFRUGFRQQHFWRUIURPWKH DPSOL¿HU
receptacle and with the aid of a small screwdriver the
small drawer in the receptacle can be withdrawn allowing
access to the mains power Fuse.
WARNING! USE THE CORRECT REPLACEMENT
VALUE ONLY!
A WORD OF ADVICE about fuses – if a fuse blows
it is usually for a very good reason, it could be anything
from a voltage spike on the mains power, to a serious
malfunction of your amplifier. Fuses are there for your
protection – treat them with respect, and never replace
with the wrong value!
W A R N I N G ! D O N O T U S E W I T H O U T
CONNECTING THE EARTH (GROUND) WIRE.
W A R N I N G ! U S E T H E C O R R E C T
REPLACEMENT VALUE ONLY!
W A R N I N G ! U S E T H E C O R R E C T
REPLACEMENT VALUE ONLY!
+7)XVH 7P$WLPHODJ9UDWHGPPJODVVIXVH
0DLQV)XVH 9+]VXSSO\ 7$WLPHODJ
250V rated 20mm glass fuse
0DLQV)XVH 9+]VXSSO\ 7$WLPHODJ9
rated 20mm glass fuse
0DLQV)XVH 9+]VXSSO\ 7$WLPHODJ9
rated 20mm glass fuse
0DLQV)XVH 9+]VXSSO\ 7$WLPHODJ
250V rated 20mm glass fuse
7&7+'LPHQVLRQVPP :[+['
Weight = 15Kg
7&7& [´ 'LPHQVLRQV PP : [ + [
':HLJKW .J
AMI 2 WAY FOOT-PEDAL – the 2 way foot-pedal supplied
ZLWK\RXU7&7DPSOL¿HUKDVDFRXSOHRIIHDWXUHVWKDW\RX
may want to be made aware of. Firstly the supplied stereo
MDFNFDEOHFDQEHUHSODFHGLIUHTXLUHGE\DQ\ó´6WHUHR
-DFNOHDG±HLWKHUVFUHHQHGRUXQVFUHHQHG6HFRQGO\WR
KHOSWKHIRRWSHGDO¿WEHWWHULQZLWK\RXUQRUPDOVWDJHVHW
up, the cable connection can be made Right Hand (as
VXSSOLHGRUFDQEHFRQYHUWHGWR/HIW+DQGFRQQHFWLRQ
Please see the diagram below: -
RII$;(&&GRXEOHWULRGHVPDOOVLJQDOYDOYHWXEH
0DLQV)XVH 9+]VXSSO\ 7$WLPHODJ
250V rated 20mm glass fuse
0DLQV)XVH 9+]VXSSO\ 7$WLPHODJ9
rated 20mm glass fuse
0DLQV)XVH 9+]VXSSO\ 7P$WLPHODJ
250V rated 20mm glass fuse
0DLQV)XVH 9+]VXSSO\ 7P$WLPHODJ
250V rated 20mm glass fuse
7
TCT 35.indd 10 2011-5-11 14:16:00

8
series
TCT 35.indd 11 2011-5-11 14:16:00

OPERATING MANUAL AND USER GUIDE
,$*+RXVH6RYHUHLJQ&RXUW(UPLQH%XVLQHVV3DUN+XQWLQJGRQ&DPEV3(;8(QJODQG
www.albionamps.com
The information in this brochure is subject to change without notice.
All rights reserved © 2010 Albion. Albion is a member of the IAG Group.
TCT 35.indd 12 2011-5-11 14:16:02
Table of contents
Other Albion Amplifier manuals