Alico M001S User manual

M001S
WARNING
！
！
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIP OVER.
SMALL PARTS- NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a
qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may
cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual.
Do not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect
assembly or inappropriate use.
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
Single Monitor Desk Mount
75x75\100x100
VESA Plate
e (x1)
Monitor Arm
d (x1)
C-Clamp
b (x1)
C-Clamp Brace
c (x1)
Pole
a (x1)
Wire Clip
n (x1)
Grommet Base Plate
m (x1)
M4 Spacer
s (x4)
M8x12 Bolt
g (x2)
Nut
h (x1)
M5x14 Bolt
f (x3)
Wrench
p (x1)
Allen Key
o (x1)
M4x30 Bolt
r (x4)
M4x12 Bolt
q (x4)
M10 Bolt
i (x1)
Support Plate
j (x1)
M10 Washer
k (x1)
Spring Washer
l (x1)
INSTALLATION MANUAL
1-844-SATTLER (18447288537)
[email protected]
www.walielectric.com
(10kg/22lbs)
RATED
MAX 27”
TIPOVER WARNING
● NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR STAND.
● USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL.
Supplied Parts List
Option A : Clamp Installation
1. Connect Pole a and C-Clamp Brace c from the bottom using M5x14 Bolt f and
tighten with Allen Key 3mm o .
1
2. Select the preferred height according to your desk thickness. Connect C-Clamp b to C-Clamp
Brace c using M8x12 Bolt g and tighten with Allen Key 5mm o . Rotate the hand knob
clockwise to fasten for stability.
Hand Knob
a
c
c
c
f
o
o
o
g
g
b
b
a c f
o
o
a
m
f
Option B : Grommet Base Installation
1. Place Pole a onto Grommet Base Plate m . Connect them from the bottom using M5x14
Bolt and tighten with Allen Key 3mm .
o
a m f

j
a
j
k
l
i
p
Select bolts and spacers (if needed) according to your TV/Monitor. Attach the VESA Plate to the Monitor and tighten with a screwdriver. (Screwdriver not included).
7Manually swivel, tilt, and rotate the monitor for the best viewing angle. 6Guide the cable through the Wire Clips n1 and store the Allen Keys o in the Wire Clip n1 .
n n
o
aja
j
k
lp
i
on
Step 3.1
Select Monitor Screws
2a. Existing Grommet Hole Installation
If the existing grommet hole comes with a plastic protector, remove it to ensure a flat surface before
installing the desk mount. Position the Pole a on the mounting surface and secure using the
Support Plate j , M10 Washer k , Spring Washer l , and M10 Bolt i . Fasten the Bolt using
the provided Wrench p .
2b. Self-drilled Grommet Hole Installation
Mark the position of the hole on your mounting surface. Drill a 3/8" (10mm) diameter hole at the
marked position through the mounting surface. Position the Pole a on the mounting surface and
secure using the Support Plate j , M10 Washer k , Spring Washer l , and M10 Bolt i . Fasten
the Bolt using the provided Wrench p .
Step 3.3a
Flat Back Monitor
Step 3.3b
Curved or Recessed Back Monitor
e
e
r
s
q
4Put the assembled TV/Monitor onto the Monitor Arm d and tighten the VESA Plate e with
Nut h for stability.
h
de
M4x12 M4x30
p
jkli
aa
jkl
p
i
d
2Put the Wire Clip n1 and Monitor Arm d through the Pole a , adjust the preferred height and
tighten using Allen Key 6mm o .
d
n a
o
ø 10mm
(ø ")3/8
3
Only one screw size fits your Monitor
Step 3.2
Select Spacers ( if needed )
Hand thread screws into the
threaded inserts on the back
of your Monitor to determine
which screw (M4x12 or M4x30)
to use.
Notice: Please make sure the security nut is installed before you rotate the monitor.
h
o
n
dd
h
e
o
5Adjust the tilt angle using Allen Key 5mm n .
o
h
+90° -90°