Alink WNAP 3G User manual

WNAP 3G MOBILE ROUTER
Quick Installation Guide

Quick Installation Guide of WNAP 3G Mobile Router
2 of 10
1At lease one PC with IEEE802.11b/g/n WLAN client or 10/100Mb Ethernet adapter installed.
2One straight-through Category 5 Ethernet cable, used to link WAN interface to xDSL or CM for Internet connection or 3G
USB modem for your 3G Internet connection.
3WNAP 3G Mobile Router.
Check package contents:
9WNAP 3G Mobile Router
9DC PowerAdapter
9User’s manual CD-ROM
91.8M RJ-45 Cable Line (Option)
Collect Installation Information:
WAN configuration (Contact your ISP or network administrator for these information’s below)
DHCP Client
Static IP
IPAddress FFF . FFF . FFF . FFF
Subnet Mask FFF . FFF . FFF .FFF
Default Gateway FFF . FFF . FFF . FFF
DNS Address FFF . FFF . FFF . FFF
PPPoE
User Name
Password
PPTP
IPAddress FFF . FFF . FFF . FFF
Subnet Mask FFF . FFF . FFF .FFF
Server IPAddress FFF . FFF . FFF . FFF
User Name
Password
L2TP
IPAddress FFF . FFF . FFF . FFF
Subnet Mask FFF . FFF . FFF .FFF
Server IPAddress FFF . FFF . FFF . FFF
User Name
Password
※To avoid users without access right through your WNAP3G Mobile Router, it is suggested to chan
g
e WLAN SSID
and password and admin password for web configuration login.
Preparation

Quick Installation Guide of WNAP 3G Mobile Router
3 of 10
GSM 3.5G
3.5G Device
APN
PIN
LAN configuration
IPAddress FFF . FFF . FFF . FFF
Subnet Mask FFF . FFF . FFF . FFF
WLAN configuration
SSID
Mode
Channel Number
USB Parts and Functions of WNAP 3G Mobile Router:
Panel Description
LED Indicator State Description
1. PWR LED On The WNAP 3G Mobile Router is powered on.
Off The WNAP 3G Mobile Router is powered off.
2. WLAN LED Flashing WLAN is active
Off WLAN is off
3. WPS LED Flashing The WPS feature is Enabled.
Off The WPS feature is Disabled.
4. WAN LED Flashing Data is transmitting or receiving on the WAN
On Port linked.
Off No link.
5. LAN LED Flashing Data is transmitting or receiving on the LAN
On Port linked.
Off No link.
Power LED
WLAN LED
LAN LED
WAN LED
WPS LED

Quick Installation Guide of WNAP 3G Mobile Router
4 of 10
Reset
LAN
WAN
WPS Powe
r
USB
Interfaces Description
Antenna (SMA) The Wireless LAN Antenna.
PWR (Power) The power jack allows an external DC power supply
connection.
The external DC adaptor provide adaptive power requirement
to the WLAN Broadband Router.
LAN The RJ-45 sockets allow LAN connection through Category 5
cables. Support auto-sensing on 10/100M speed and half/ full
duplex; comply with IEEE 802.3/ 802.3u respectively.
WAN The RJ-45 socket allows WAN connection through a Category
5 cable. Support auto-sensing on 10/100M speed and half/ full
duplex; comply with IEEE 802.3/ 802.3u respectively.
WPS Push continually the reset button 5 ~ 10 seconds to enable the
WPS feature.
USB The USB port allows you to connect 3G USB modem for
Internet connection or USB Storage connection to support FTP
server, File server.
RS (Reset) Push continually the reset button 5 ~ 10 seconds to reset the
configuration parameters to factory defaults.

Quick Installation Guide of WNAP 3G Mobile Router
5 of 10
Installation
Step One – Power On WNAP 3G Mobile Router
Connect DC Power Adapter to WLAN Broadband Router and the wall power socket.
Notice: It will take about 50 seconds to complete the boot up sequence after powered on
the WNAP3G Mobile Router; Power LED will be active, and after that the
WLAN Activity LED will be flashing to show the WLAN interface is enabled
and working now.
Step Two – Configure WNAP 3G Mobile Router
1. Connect your PC to LAN port for configuration setting. WNAP 3G Mobile Router is delivered with
the following factory default parameters on the Ethernet LAN interfaces.
Default IPAddress: 192.168.1.254
Default IP subnet mask: 255.255.255.0
WEB login User Name: admin
WEB login Password: admin
Configure your PC with IP address
between 192.168.1.1 to 192.168.1.253
and subnet mask to be 255.255.255.0,
then open an Internet browser (i.e.
Microsoft IE6.1 SP1 or above) to
connect WNAP 3G Mobile Router by
entering http://192.168.1.254 to URL
field.
The following example is to configure router as “Gateway” mode that use factory default value.
You may change those values if you think that is necessary.

Quick Installation Guide of WNAP 3G Mobile Router
6 of 10
2. Click “Setup Wizard” in submenu of Site contents
Click “Next>>” button to
go next.
3. Configure Operation Mode
Click “Gateway”.
Click “Next>>” button to
go next.

Quick Installation Guide of WNAP 3G Mobile Router
7 of 10
4. Configure Time Zone Setting configuration
Click “Next>>” button to
go next.
5. Configure LAN Interface Setup
IPAddress:
192.168.1.254.
Subnet Mask:
255.255.255.0.
Click “Next>>” button to
go next.
6. WAN Interface Setup
WAN Access Type: Select
WAN connection of ISP
provides.
WAN Options: Static IP,
DHCP Client, PPPoE,
PPTP, L2TP, GSM 3.5G
Click “Next>>” button to
go next.

Quick Installation Guide of WNAP 3G Mobile Router
8 of 10
7. Wireless Basic Settings
Band: 2.4GHz(B+G)
Mode: AP
Network Type: disabled
SSID: WNAP
Channel: Auto
Enable Mac Clone: disabled
Click “Next>>” button to go next.
8. Wireless Security Setup
Encryption: WPA2 Mixed
Options:
None, WEP, WPA (TKIP),
WPA2 (AES), WPA2 Mixed
Click “Finished” button to close
setup session.

Quick Installation Guide of WNAP 3G Mobile Router
9 of 10
Step Three – Connect WLAN client to WNAP 3G Mobile Router wirelessly
On your wireless client PC:
1. Move your mouse to the
Network icon on the Task
bar and right click the
mouse button to bring up
the pop-up menu.
2. Click the View Available
Wireless Networks on the
pop-up menu.
3. Select the specific WLAN
network (SSID) from the
Available Networks list.
4. Click the Connect button
to establish the
communication link to the
wireless network
1
2
3
4

Quick Installation Guide of WNAP 3G Mobile Router
10 of 10
Power adapter
Et he rnet cab le
xDSL/CM
Eth er ne t
Cable
In ter n et
The wireless network diagram of WNAP 3G Mobile Router..
Reference
Please consult the user’s manual of WNAP 3G Mobile Router for detailed and complete operation guide.
Product is in accordance with directive 1999/5/EY (CE).
WNAP(b) EAN: 64 18949 02217 7
Product importer, repairs and technical support :
A-Link Europe Ltd, Kylävainiontie 20, FI-02760 Espoo, Finland
Technical support : [phone] (2,70€ / min + local network fee)
Internet : http://www.a-link.com E-mail : [email protected]
Allrightsreserved
Copyright © 2010 A-link Europe Ltd 10g05T WNAPb QIG