All American Scoreboards MP-3909 Troubleshooting guide

OPERATING INSTRUCTIONS AND SERVICE MANUAL
MOONBUGGY RACING SCOREBOARD
MODEL MP-3909 WITH MP-2002 Control
EFFECTIVE S.N. 16155 June 23, 2000

TABLE OF CONTENTS
1. General Information
1.1 Description
1.2 Identification
1.3 Damage
1.4 Damage Claim procedure
2. Installation
2.1 General Information
2.2 Inspection
2.3 Pre-Test
2.4 Installation
2.5 Electrical Connection
3. Control Console Operation
3.1 Scoreboard Power
3.2 Control Console Power
3.3 Control Console Display
3.4 Time Setting and Control
3.5 Team Number
4. Maintenance And Troubleshooting
4.1 Introduction
4.2 Test Equipment
4.3 Troubleshooting
4.4 Troubleshooting Guide
5. Replacement Parts List
5.1 Display Parts
5.2 Controller Assembly Parts
6. Diagrams
6.1 Keyboard Insert (Slipsheet)
6.2 Timer System Layout
6.3 Single Junction Box Wiring
6.4 Power Wiring
6.5 Controller Plate Wiring and Layout
6.6 Microprocessor 4x7 Lamp Pattern (8 Bit)
6.7 Figuregram Wiring Diagram
6.8 Jumper Location on Three Position System
6.9 Triac Placement Diagram
6.10 Installation Drawings
2

1. GENERAL INFORMATION
1.1 Description
Your All-American scoreboard has been carefully inspected and tested before leaving the factory.
It is possible, however, that components may be loosened or forced out of adjustment in transit.
If this occurs, follow the troubleshooting guide (section 4). If equipment then fails to operate,
contact immediately:
ALL-AMERICAN Service Department
EVERBRITE LLC
P.O. Box 100
Pardeeville, WI 53954
Telephone: [phone]
Toll Free: 800-356-8146
E-mail: [email protected]
Parts being returned for repair are to be sent to:
ALL-AMERICAN Service Department
EVERBRITE LLC
401 S. Main Street
Pardeeville, WI 53954
NOTE
If you need to send parts in for repair, please call the ALL AMERICAN
service department for a returned goods authorization (RGA) number.
1.2 Identification
ALL-AMERICAN uses a 5 digit serial number for scoreboard identification. The serial number
tags are located on the back of the control console and the lower right hand corner on the face
of the scoreboard display. When contacting the factory for assistance it is important that the
model number and serial number are known.
1.3 Damage
Upon receipt of equipment, check for visible damage. If this occurs, or if damage is found after
shipment has been accepted, follow the damage claim procedure.
1.4 Damage Claim Procedure
An instruction sheet is enclosed advising the consignee in case of damage in transit. If damage
is noted at the time of delivery, consignee must obtain an 'Inspection of Bad Order' from the
delivering carrier. In order to process your claim, this must be properly filled out with a
complete statement of all damage and it must be signed by the carrier.
3

If damage is discovered after delivery, you should call the delivery company. Have them make
out a Concealed Damage Report. Fifteen days after delivery are allowed, so this should be done
promptly or it is impossible to process this claim.
Advise EVERBRITE corporation of necessary replacement parts, or repairs. Consignee will be
invoiced and then should file a claim with the carrier to recover charges. To file your claim
follow this procedure:
(A) Cost of replacement parts, or repair charges, are invoiced to the carrier by the consignee.
(B) The following documents, properly filled out, plus invoice, are forwarded to the
trucking company in support of your claim:
(a) Original bill of lading
(b) Original paid freight bill
(c) Certified copy of original invoice
(d) Standard form for presentation of loss and damage claim
2. INSTALLATION
2.1 General Information
Shipping papers accompany each scoreboard. Check carefully to see that you receive the
following:
1 ea Scoreboard Display
1 ea Control Console
1 ea Service Manual
1 ea Mounting Stand Hardware Package
IMPORTANT!
The MP-40 cable supplied by ALL AMERICAN SCOREBOARDS for use on the
Microprocessor based scoreboards is specifically designed for this system. Use of
a substitute cable may void the warranty on the scoreboard!
2.2 Inspection
Inspect each unit and tighten all screws, lamps, and fittings that may have loosened in shipment.
2.3 Pre-Test
Before installing the scoreboard, pre-test all functions.
2.4 Installation
Select the location best suited for visibility by the majority of spectators. Preferred position is
4

facing east or north to avoid direct sunlight on the face of the scoreboard, if day games are
played.
The MP-40 direct burial data cable carries only low voltage signals and therefore can be installed
with or without conduit. consult section 6 for junction box and scoreboard wiring.
2.5 Electrical connections
This scoreboard requires a 120 V. 60 HZ 2 wire with ground 15 AMP service for the exclusive
use of the scoreboard.
NOTE
To protect the MP-2002 control from damage, it is advisable that you disconnect the
control and store in a dry secure area when not in use.
CAUTION !
THIS SCOREBOARD CONTROL IS EQUIPPED WITH EITHER A 5 OR 6 PIN
CONNECTOR ON THE CONTROL CONSOLE AND IN THE JUNCTION BOX.
DAMAGE TO THE SCOREBOARD AND CONTROL CAN OCCUR IF YOU
PLUG A CONTROL CONSOLE FROM ANOTHER SCOREBOARD MODEL
INTO THIS SCOREBOARD.
NOTE
This equipment is ETL (Electronics Testing Laboratories) CSA and NRTL approved
and complies with the requirements in part 15 of the FCC rules for a class A
computing device. Operation of this equipment in a residential area may cause
unacceptable interference to radio and television reception, requiring the operator to
take whatever steps are necessary to correct the interference.
3. CONTROL CONSOLE OPERATION
3.1 Scoreboard Power
Turn on the power to the display. The display will show "0:00" .
3.2 Console Power
Push
ON/OFF once to turn the console on.
Push
ON/OFF a second time to shut the console off.
When first turned on; the console display should show CODE .
5

Enter the two digit code (88) shown in the lower center window of the keyboard as in the
following example:
Push CODE 8 8 ENTER .
When the proper code has been entered, the console display will show :00 .
3.3 Console Display
The 4 digit Liquid Crystal Display (LCD) shows the time and information entered from the
keyboard.
3.4 Time Setting and Control
To set a 15 minute period, Push: SET 1 5 0 0 ENTER .
The timer will now count down from 15 minutes and stop at zero.
Any time up to 99 minutes may be preset in a similar manner.
The UP/DN key determines the timer mode. In the up mode the timer will count from zero
up.
Push IN/OUT to start/stop the timer.
Push RESET to return the timer to the previously set value.
3.5 Team Number
To set the Team number push TEAM followed by the team number, and then
push
ENTER .
The scoreboard will now display the Team Number.
4. MAINTENANCE AND TROUBLESHOOTING
4.1 Introduction
This section gives maintenance and troubleshooting information. Included are troubleshooting
guides for typical scoreboard malfunctions. If the cause of a problem cannot be determined,
please contact the customer service department.
6

4.2 Test Equipment
IMPORTANT !!!
In this scoreboard the 120 volt line is on the lamp socket all the time, and the
common is switched to turn the lamps on and off. For this reason, to avoid
damage to the equipment or personal injury, it is important to turn the main
power off when changing the lamps.
A simple analog or digital voltmeter will be sufficient for all user repairable problems. Printed
circuit boards requiring troubleshooting should be returned to the factory.
WARNING
120 VAC wires are exposed whenever the cover over the controller assembly
is removed from the scoreboard. Use extreme caution during troubleshooting
or repair. To avoid possible damage always remove power before removing
the cover or replacing assemblies.
4.3 Troubleshooting
Whenever possible, follow the troubleshooting guides prior to contacting the customer service
department. If a problem not described in the guides exists, contact the customer service
department immediately. Refer to the diagrams provided for assistance in troubleshooting
scoreboard malfunctions.
4.4 Troubleshooting Guides
(A) Scoreboard doesn't light and console doesn't work
(a) Check that the main power switch is turned on.
(b) Replace any defective or blown fuses.
(c) Check the power connections and voltages at the scoreboard.
(d) Contact the customer service department.
(B) Scoreboard digits don't light, but the console works
(a) With the main power switch "off"; remove the cover over the controller assembly.
(b) Check all connections.
(c) Turn the main power on.
(d) If the scoreboard still doesn't light, check the transformer voltage going to the receiver
PCB (printed circuit board) assembly (blue wires) using a voltmeter set on the 12 VAC
7

or higher scale.
If the voltage is less than 8 VAC, contact the customer service department.
If the voltage is between 8-12 VAC, see the replacement parts list for a receiver PCB
assembly, and contact the customer service department.
(C) The scoreboard digits light but the console doesn't work
(a) Check for continuity between the scoreboard and the junction box.
(b) If an open circuit is found, the problem is either the cable or a cable connection.
(c) If the continuity test checks good, check the voltage between the green wire and the white
wire in the junction box, using a voltmeter set on the 12 VAC or higher scale.
If the voltage is 0 VAC see the controller parts list for a transformer assembly.
If the voltage is less than 8 VAC consult the controller wiring diagram for instructions
on long cable compensation.
If the voltage is between 8 VAC and 12 VAC contact the customer service department.
(D) The scoreboard digits light, the console works, but there is no control of the scoreboard.
(a) Check the voltage between the black and red wires in the junction box with a voltmeter set
set on the 3 VDC or higher scale. The voltage should read somewhere between 2-3 VDC
when the console is working properly.
(b) If the voltage is 0 VDC contact the customer service department for assistance.
(c) If the voltage is correct, (2-3 VDC) check that this reading also appears at the scoreboard.
(d) If the correct voltage also appears at the scoreboard, see the replacement parts list for a
receiver PCB assembly.
(E) The scoreboard works, but some lights stay on all the time
(a) With the main power "OFF", switch the plug from the bad digit with the plug for a
known good digit.
EXAMPLE: Plug "A" into "B" and "B" into "A" locations.
(b) Turn the power back on. If the same lamps remain lit all the time, the problem is a shorted
lamp socket. If the lamps on a different digit now stay lit all the time, the problem is on the
driver PCB assembly. See the replacement parts list for the proper replacement part.
(F) The scoreboard works, but some lights do not come on.
(a) Check for burned out lamps.
(b) Check for a broken wire or bad connection on the 12 pin connector.
(c) See the replacement parts list for the proper replacement driver board.
8

5. REPLACEMENT PARTS LIST
5.1 Scoreboard Display Parts
figure 1
DISPLAY ASSEMBLY
9

REPLACEMENT PARTS LIST (MP-3909)
fig.& MFG PART REF VENDOR
index NUMBER DESCRIPTION DES PART #
1- 000000 Display Assembly 000000
1-1 850022 Lamp, 15W/130V CL 15A15 CL
1-1A 930677 Lamp, 30W/130V IF 30A15 IF
1-2 SU479000 Controller Assembly A2 SU479300
*****SEE FIGURE 2*****
1-3 EL00079 Rainshield EL00079
1-4 EL00080 Rainshield Cover EL00080
1-5 000000 Service Door 000000
1-6 705913 Screen, for 15" 0-99 705913
1-7 EL044100 Resistor, 2 OHM 30 WATT HL-24-09Z
1-8 SU00038 Fuse Box Assy, SU00038
1-9 180199 Fuse, 20A 250V 1/4 X 1 1/4" F1-F3 AGC-20
1-10 EL055800 Terminal Block, 3C B-03 EAGLE
120387 Control Console 120387X
***** PROGRAM SCRACE.HEX *****
119771 Slipsheet 119771
150184 Transmitter PCB Assembly A1 150184
702785 Connector, 5 Pin Male Cable P1 RM12BPG5P
151002 Junction Box, Single Press Box 151002
702786 Connector, 5 Pin Female J1 RM12BRD5S
150508 Cable, MP-40 Control YR21233
10

5.2 Scoreboard Controller Assembly Parts
figure 2
CONTROLLER ASSEMBLY
REPLACEMENT PARTS LIST (MP-3909) Controller Assembly
fig.& MFG PART REF VENDOR
index NUMBER DESCRIPTION DES PART #
2- SU479000 Controller Assembly A2 SU479300
2-1 119323 Receiver PCB Assembly A3 119323
*** PROGRAM SPSWY.CNT ***
2-2 118922 Driver PCB Assembly, 3 Position A4-A5 118922
2-3 118522 Transient Suppressor PCB Assembly A8 118522
2-4 701137 Terminal Block, 7C TB1&2 670-7
2-5 703719 Transformer, 8V/18V T1/T2 CS-697
2-7 705723 Spacer, P.C. Board LCBS-6-01
11

6. DIAGRAMS
6.1 Control Console Keyboard and Slipsheet Layout
12

CONSOLE KEYBOARD
6.2 Scoreboard System Layout
SYSTEM LAYOUT
13

6.3 Single Junction Box Wiring
14

SINGLE JUNCTION BOX WIRING
6.4 Power Wiring
POWER WIRING
15

6.5 Controller Assembly Wiring
CONTROLLER ASSEMBLY
16

6.6 Microprocessor 4 X 7 Lamp Pattern (8 Bit)
MICROPROCESSOR 4 X 7 (8 BIT) LAMP PATTERN
17

6.7 Figuregram Wiring
8 BIT FIGUREGRAM WIRING
18

6.8 Jumper Location on 3 Position System
All of the 3 position drivers and receivers are identical except for the jumper on each board.
Make sure the jumpers are set for the model of scoreboard you are installing them into.
(A) On the receiver board (refer to figure); Jumper pins 2 & 3 for models MP-3385,
MP-3312, MP-3529, and MP-3549. Jumper pins 1 & 2 for all other models.
(B) On the driver board (refer to figure); Jumper pins 1 & 2 for use of a horn. Jumper pins
2 & 3 for all others.
JUMPER LOCATION
19

6.9 Triac Placement
The triac is the switch that controls the figuregram lamps. The triacs for any given figuregram
are adjacent to the twelve pin connector on the driver board that controls that figuregram. Shown
below is the triac placement and bit designation relative to the figuregram bit pattern.
MP TRIAC PLACEMENT
20