Allen-Bradley 1734-OE4C User manual

Installation Instructions
POINT I/O 4 Channel Analog Current
Output Module
Catalog numbers 1734-OE4C
Table of Contents
Topic Page
Important User Information 2
Environment and Enclosure 3
Preventing Electrostatic Discharge 3
North American Hazardous Location Approval 4
European Hazardous Location Approval 5
Before You Begin 6
Install the Mounting Base 8
Install the Module 9
Install the Removable Terminal Block 11
Remove a Mounting Base 13
Wire the Module 14
Communicate with Your Module 15
Interpret Status Indicators 16
Specifications 17

2POINT I/O 4 Channel Analog Current Output Module
Publication 1734-IN034C-EN-E - August 2016
Important User Information
Solid-state equipment has operational characteristics differing from those of electromechanical
equipment. Safety Guidelines for the Application, Installation and Maintenance of Solid State Controls
(Publication SGI-1.1 available from your local Rockwell Automation sales office or online at
http://www.rockwellautomation.com/literature/) describes some important differences between
solid-state equipment and hard-wired electromechanical devices. Because of this difference, and also
because of the wide variety of uses for solid-state equipment, all persons responsible for applying this
equipment must satisfy themselves that each intended application of this equipment is acceptable.
In no event will Rockwell Automation, Inc. be responsible or liable for indirect or consequential damages
resulting from the use or application of this equipment.
The examples and diagrams in this manual are included solely for illustrative purposes. Because of the
many variables and requirements associated with any particular installation, Rockwell Automation, Inc.
cannot assume responsibility or liability for actual use based on the examples and diagrams.
No patent liability is assumed by Rockwell Automation, Inc. with respect to use of information, circuits,
equipment, or software described in this manual.
Reproduction of the contents of this manual, in whole or in part, without written permission of Rockwell
Automation, Inc., is prohibited.
Throughout this manual, when necessary, we use notes to make you aware of safety considerations.
WARNING: Identifies information about practices or circumstances that can cause an
explosion in a hazardous environment, which may lead to personal injury or death,
property damage, or economic loss.
ATTENTION: Identifies information about practices or circumstances that can lead to
personal injury or death, property damage, or economic loss. Attentions help you
identify a hazard, avoid a hazard and recognize the consequences.
SHOCK HAZARD: Labels may be on or inside the equipment (for example, drive or
motor) to alert people that dangerous voltage may be present.
BURN HAZARD: Labels may be on or inside the equipment (for example, drive or
motor) to alert people that surfaces may reach dangerous temperatures.
IMPORTANT
Identifies information that is critical for successful application and understanding of
the product.

POINT I/O 4 Channel Analog Current Output Module 3
Publication 1734-IN034C-EN-E - August 2016
Environment and Enclosure
Preventing Electrostatic Discharge
ATTENTION: This equipment is intended for use in a Pollution Degree 2
industrial environment, in overvoltage Category II applications (as defined in IEC
60664-1), at altitudes up to 2000 m (6562 ft) without derating.
This equipment is considered Group 1, Class A industrial equipment according
to IEC/CISPR 11. Without appropriate precautions, there may be difficulties
with electromagnetic compatibility in residential and other environments due to
conducted and radiated disturbances.
This equipment is supplied as open-type equipment. It must be mounted within
an enclosure that is suitably designed for those specific environmental
conditions that will be present and appropriately designed to prevent personal
injury resulting from accessibility to live parts. The enclosure must have
suitable flame-retardant properties to prevent or minimize the spread of flame,
complying with a flame spread rating of 5VA, V2, V1, V0 (or equivalent) if
non-metallic. The interior of the enclosure must be accessible only by the use of
a tool. Subsequent sections of this publication may contain additional
information regarding specific enclosure type ratings that are required to
comply with certain product safety certifications.
In addition to this publication, see the following:
• Industrial Automation Wiring and Grounding Guidelines, for additional
installation requirements, Allen-Bradley publication 1770-4.1.
• NEMA Standards publication 250 and IEC publication 60529, as applicable,
for explanations of the degrees of protection provided by different types of
enclosure.
ATTENTION: This equipment is sensitive to electrostatic discharge, which can
cause internal damage and affect normal operation. Follow these guidelines
when you handle this equipment:
• Touch a grounded object to discharge potential static.
• Wear an approved grounding wrist strap.
• Do not touch connectors or pins on component boards.
• Do not touch circuit components inside the equipment.
• Use a static-safe workstation, if available.
• Store the equipment in appropriate static-safe packaging when not in use.

4POINT I/O 4 Channel Analog Current Output Module
Publication 1734-IN034C-EN-E - August 2016
North American Hazardous Location Approval
The following information applies when
operating this equipment in hazardous
locations:
Informations sur l’utilisation de cet équipement
en environnements dangereux:
Products marked “CL I, DIV 2, GP A, B, C, D” are
suitable for use in Class I Division 2 Groups A, B, C,
D, Hazardous Locations and nonhazardous locations
only. Each product is supplied with markings on the
rating nameplate indicating the hazardous location
temperature code. When combining products within
a system, the most adverse temperature code
(lowest “T” number) may be used to help determine
the overall temperature code of the system.
Combinations of equipment in your system are
subject to investigation by the local Authority Having
Jurisdiction at the time of installation.
Les produits marqués “CL I, DIV 2, GP A, B, C, D” ne
conviennent qu'à une utilisation en environnements de
Classe I Division 2 Groupes A, B, C, D dangereux et non
dangereux. Chaque produit est livré avec des marquages
sur sa plaque d'identification qui indiquent le code de
température pour les environnements dangereux. Lorsque
plusieurs produits sont combinés dans un système, le code
de température le plus défavorable (code de température le
plus faible) peut être utilisé pour déterminer le code de
température global du système. Les combinaisons
d'équipements dans le système sont sujettes à inspection
par les autorités locales qualifiées au moment de
l'installation.
EXPLOSION HAZARD
• Do not disconnect equipment unless
power has been removed or the area
is known to be nonhazardous.
• Do not disconnect connections to
this equipment unless power has
been removed or the area is known
to be nonhazardous. Secure any
external connections that mate to
this equipment by using screws,
sliding latches, threaded connectors,
or other means provided with this
product.
• Substitution of components may
impair suitability for Class I, Division
2.
• If this product contains batteries,
they must only be changed in an
area known to be nonhazardous.
RISQUE D’EXPLOSION
• Couper le courant ou s'assurer que
l'environnement est classé non
dangereux avant de débrancher
l'équipement.
• Couper le courant ou s'assurer que
l'environnement est classé non
dangereux avant de débrancher les
connecteurs. Fixer tous les connecteurs
externes reliés à cet équipement à l'aide
de vis, loquets coulissants, connecteurs
filetés ou autres moyens fournis avec ce
produit.
• La substitution de composants peut
rendre cet équipement inadapté à une
utilisation en environnement de Classe I,
Division 2.
• S'assurer que l'environnement est classé
non dangereux avant de changer les
piles.
ATTENTION: To comply with UL restrictions, field power and all connected
devices must be powered from a single source compliant with the following:
Class 2
ATTENTION: To comply with the CE Low Voltage Directive (LVD), field power
and all connected I/O must be powered from a source compliant with the
following:
Safety Extra Low Voltage (SELV) or Protected Extra Low Voltage (PELV).

POINT I/O 4 Channel Analog Current Output Module 5
Publication 1734-IN034C-EN-E - August 2016
European Hazardous Location Approval
The following applies when the product bears the Ex Marking
This equipment is intended for use in potentially explosive atmospheres as defined by European Union
Directive 94/9/EC.
DEMKO certifies that this equipment has been found to comply with the Essential Health and Safety
Requirements relating to the design and construction of Category 3 equipment intended for use in Zone
2 potentially explosive atmospheres, given in Annex II to this Directive.
Compliance with the Essential Health and Safety Requirements has been assured by compliance with
EN 60079-0:2012+A11:2013, EN 60079-15:2010, reference certificate number DEMKO
04ATEX0330347X.
WARNING: This equipment shall be mounted in an ATEX certified enclosure
with a minimum ingress protection rating of at least IP54 (as defined in
IEC60529) and used in an environment of not more than Pollution Degree 2 (as
defined in IEC 60664-1) when applied in Zone 2 environments. The enclosure
must utilize a tool removable cover or door.
WARNING: This equipment shall be used within its specified ratings defined
by Rockwell Automation.
WARNING: Provision shall be made to prevent the rated voltage from being
exceeded by transient disturbances of more than 140% of the rated voltage
when applied in Zone 2 environments.
WARNING: This equipment must be used only with ATEX certified Rockwell
Automation backplanes.
WARNING: Secure any external connections that mate to this equipment by
using screws, sliding latches, threaded connectors, or other means provided
with this product.
WARNING: Do not disconnect equipment unless power has been removed or
the area is known to be nonhazardous.
ATTENTION: If this equipment is used in a manner not specified by the
manufacturer, the protection provided by the equipment may be impaired.
ATTENTION: This equipment is not resistant to sunlight or other sources of
UV radiation.

6POINT I/O 4 Channel Analog Current Output Module
Publication 1734-IN034C-EN-E - August 2016
Before You Begin
Note that this series C product can be used with the following:
• DeviceNet and PROFIBUS adapters
• ControlNet and EtherNet/IP adapters, using RSLogix 5000 software, version 11
or later
See the figures to familiarize yourself with major parts of the module, noting that the
wiring base assembly is one of the following:
• 1734-TB or 1734-TBS POINT I/O two-piece terminal base, which includes the
1734-RTB removable terminal block and 1734-MB mounting base
• 1734-TOP or 1734-TOPS POINT I/O one-piece terminal base
POINT I/O 4 Channel Analog Current Output Module
Module
Status
Network
Status
NODE:
0
1
2
3
1
10
9
8
7
2
3
4
5
6
44328

POINT I/O 4 Channel Analog Current Output Module 7
Publication 1734-IN034C-EN-E - August 2016
Description Description
1 Module locking mechanism 6 Mounting base – 1734-TB, 1734-TBS
2 Slide-in writable label 7 Interlocking side pieces
3 Insertable I/O module 8 Mechanical keying (orange)
4 Removable Terminal Block (RTB) handle 9 DIN rail locking screw (orange)
5 RTB with screw or spring clamp 10 Module wiring diagram
Description Description
1 Module locking mechanism 6 Interlocking side pieces
2 Slide-in writable label 7 Mechanical keying (orange)
3 Insertable I/O module 8 DIN rail locking screw (orange)
4 Handle 9 Module wiring diagram
5 One-piece terminal base with screw or
spring clamp – 1734-TOP, 1734-TOPS
1
9
8
7
6
2
4
5
44221
3

8POINT I/O 4 Channel Analog Current Output Module
Publication 1734-IN034C-EN-E - August 2016
Install the Mounting Base
To install the mounting base on the DIN rail (Allen-Bradley part number 199-DR1;
46277-3; EN50022), proceed as follows:
1. Position the mounting base vertically above the installed units (adapter, power
supply or existing module).
2. Slide the mounting base down allowing the interlocking side pieces to engage the
adjacent module or adapter.
3. Press firmly to seat the mounting base on the DIN rail. The mounting base snaps
into place.
4. To remove the mounting base from the DIN rail, remove the module, and use a
small bladed screwdriver to rotate the base locking screw to a vertical position.
This releases the locking mechanism. Then lift straight up to remove.
ATTENTION: This product is grounded through the DIN rail to chassis
ground. Use zinc plated, yellow-chromate steel DIN rail to be sure of proper
grounding. The use of other DIN rail materials, such as aluminum and plastic,
which can corrode, oxidize, or are poor conductors, can result in improper or
intermittent grounding. Secure DIN rail to mounting surface approximately
every 200 mm (7.87 in.) and use end-anchors appropriately.
31586

POINT I/O 4 Channel Analog Current Output Module 9
Publication 1734-IN034C-EN-E - August 2016
Install the Module
The module can be installed before or after base installation. Make sure that the mounting
base is correctly keyed before installing the module into the mounting base. In addition,
make sure the mounting base locking screw is positioned horizontal referenced to the base.
1734-TB Base
WARNING: When you insert or remove the module while backplane power
is on, an electrical arc can occur. This could cause an explosion in hazardous
location installations.
Be sure that power is removed or the area is nonhazardous before
proceeding. Repeated electrical arcing causes excessive wear to contacts on
both the module and its mating connector. Worn contacts may create
electrical resistance that can affect module operation.
Turn the keyswitch to align the
number with the notch.
Notch position 4 is shown.
Make sure the DIN rail locking
screw is in the horizontal position.
44229

10 POINT I/O 4 Channel Analog Current Output Module
Publication 1734-IN034C-EN-E - August 2016
1734-TOP Base
1. Using a bladed screwdriver to rotate the keyswitch on the mounting base
clockwise until the number required for the type of module being installed aligns
with the notch in the base.
2. Make certain the DIN rail locking screw is in the horizontal position.
You cannot insert the module if the locking mechanism is unlocked.
3. Insert the module straight down into the mounting base and press to secure.
The module locks into place.
Turn the keyswitch to align the
number with the notch.
Notch position 4 is shown.
Make sure the DIN-rail locking
screw is in the horizontal position.
44228

POINT I/O 4 Channel Analog Current Output Module 11
Publication 1734-IN034C-EN-E - August 2016
Install the Removable Terminal Block
A Removable Terminal Block (RTB) is supplied with your wiring base assembly. To
remove, pull up on the RTB handle. This allows the mounting base to be removed and
replaced as necessary without removing any of the wiring. To reinsert the Removable
Terminal Block, proceed as follows:
1. Insert the end opposite the handle into the base unit. This end has a curved
section that engages with the wiring base.
2. Rotate the terminal block into the wiring base until it locks itself in place.
3. If an I/O module is installed, snap the RTB handle into place on the module.
WARNING: When you connect or disconnect the Removable Terminal Block
(RTB) with field side power applied, an electrical arc can occur. This could
cause an explosion in hazardous location installations.
Be sure that power is removed or the area is nonhazardous before
proceeding.
24VDC
Source
Output
Module
Status
Network
Status
1734
OB4E
NODE:
0
1
2
3
44011
Insert the module
straight down into
the mounting base
Hook the RTB end into
the mounting base end
and rotate until it locks
into place

12 POINT I/O 4 Channel Analog Current Output Module
Publication 1734-IN034C-EN-E - August 2016
WARNING: For 1734-RTBS and 1734-RTB3S, to latch and un-latch the wire,
insert a bladed screwdriver (catalog number 1492-N90 – 3 mm diameter blade)
into the opening at approximately 73° (blade surface is parallel with top surface
of the opening) and push up gently.
WARNING: For 1734-TOPS and 1734-TOP3S, to latch and un-latch the wire,
insert a bladed screwdriver (catalog number 1492-N90 – 3 mm diameter) into
the opening at approximately 97° (blade surface is parallel with top surface of
the opening) and press in (do not push up or down).
73° 85°
97°

POINT I/O 4 Channel Analog Current Output Module 13
Publication 1734-IN034C-EN-E - August 2016
Remove a Mounting Base
To remove a mounting base, you must remove any installed module, and the module
installed in the base to the right. Remove the Removable Terminal Block, if wired.
1. Unlatch the RTB handle on the I/O module.
2. Pull on the RTB handle to remove the Removable Terminal Block.
3. Press on the module lock on the top of the module.
4. Pull on the I/O module to remove from the base.
5. Repeat steps 1, 2, 3 and 4 for the module to the right.
6. Use a small bladed screwdriver to rotate the orange base locking screw to a
vertical position. This releases the locking mechanism.
7. Lift straight up to remove.
Install a 1734-TOPS Base
1. Position the base vertically above the installed units, such as an adapter, power
supply, or existing module.
2. Slide the base down, allowing the interlocking side pieces to engage the adjacent
installed unit.
3. Press firmly to seat the base on the DIN rail until the base snaps into place.
4. Verify that the DIN-rail locking screw is in a horizontal, locked position before
inserting an I/O module.
Remove a 1734-TOPS Base
1. To remove a wiring base from the DIN rail, you must remove the module
installed to the right of the base.
2. Squeeze the module locking mechanism of the module to the right of the base,
pulling up to remove the module.
3. Turn the orange locking screw to a vertical position to unlock the base from the
DIN rail.
4. Slide the base up to release it from its mating units.

14 POINT I/O 4 Channel Analog Current Output Module
Publication 1734-IN034C-EN-E - August 2016
Wire the Module
Wiring Diagram
WARNING: If you connect or disconnect wiring while the field-side power is
on, an electrical arc can occur. This could cause an explosion in hazardous
location installations. Be sure that power is removed or the area is
nonhazardous before proceeding.
Channel Current Common Supply
0046
11
5 7
22
33
DC power is provided by the internal power bus.
1734
OE4C
44352
Output 0 connection 0 Output 1 connection 1
Output 2 connection 2 Output 3 connection 3
C 4 5 C
V 6 7 V
C = Common
V = Supply
In = Output channel
Chas Gnd = Chassis Ground
C = Common
V = 24V DC supply
4-wire
AC or DC Out 0 Out 1
3
5
7
01
2
4
6
Out 2 Out 3
Current
output
device
Current
output
device
2-wire
Chas Gnd
CC
VV

POINT I/O 4 Channel Analog Current Output Module 15
Publication 1734-IN034C-EN-E - August 2016
Communicate with Your Module
I/O messages are sent to (consumed) and received from (produced) the POINT I/O
modules. These messages are mapped onto the processor’s memory.
This POINT I/O output module produces 4 bytes of input data (scanner Rx) (fault
status). It consumes 8 bytes of Output data (scanner Tx).
Default Data Map for the 1734-OE4C Analog Output Module
Message size: 4 Bytes
15 14 13 12 11 10 09 08 07 06 05 04 03 02 01 00
Produces
(scanner Rx) High Byte - Channel 1 Status High Byte - Channel 0 Status
Not used HCA LCA CM CF Not used HCA LCA CM CF
High Byte - Channel 3 Status High Byte - Channel 2 Status
Not used HCA LCA CM CF Not used HCA LCA CM CF
Where: CF = Channel Fault status; 0 = no error, 1 = fault
CM = Calibration Mode; 0 = Normal, 1 = calibration mode
LCA = Low Clamp Alarm; 0 = no error, 1 = fault
HCA = High Clamp Alarm; 0 = no error, 1 = fault
Message size: 8 Bytes
15 14 13 12 11 10 09 08 07 06 05 04 03 02 01 00
Consumes
(scanner Tx) Output Channel 0 High Byte Output Channel 0 Low Byte
Output Channel 1 High Byte Output Channel 1 Low Byte
Output Channel 2 High Byte Output Channel 2 Low Byte
Output Channel 3 High Byte Output Channel 3 Low Byte

16 POINT I/O 4 Channel Analog Current Output Module
Publication 1734-IN034C-EN-E - August 2016
Interpret Status Indicators
Refer to the following diagram and table for information on how to interpret the
status indicators.
Indicator Status for Module
Indicator State Description
Module
status Off No power applied to device.
Green Device operating normally.
Flashing green Device needs commissioning due to missing, incomplete, or
incorrect configuration.
Flashing red Recoverable fault.
Red Unrecoverable fault may require device replacement.
Flashing red/green Device is in self-test mode.
Network
status Off Device is not online: - Device has not completed dup_MAC-id test.
- Device not powered – check module status indicator.
Flashing green Device is online but has no connections in the established state.
Green Device is online and has connections in the established state.
Flashing red One or more I/O connections are in timed-out state.
Red Critical link failure – failed communication device. Device detected
error that prevents it from communicating on the network.
Flashing red/green Communication faulted device – the device has detected a network
access error and is in communication faulted state. Device has
received and accepted an Identity Communication Faulted Request
– long protocol message.
Channel
status Off Module in CAL mode.
Solid green Channel actively controlling outputs
Flashing green Channel calibrating
Flashing red Open wire or no field power present
Solid red Unused
Module status
Network status
Status of output 0
Status of output 1
Status of output 2
Status of output 3 44352
4-20mA
Analog
Output
Module
Status
Network
Status
1734
OE4C
0
1
2
3
NODE:

POINT I/O 4 Channel Analog Current Output Module 17
Publication 1734-IN034C-EN-E - August 2016
Specifications
Output Specifications
Attribute Value
Number of outputs 4 analog, single-ended, non-isolated
Resolution current 16 bits – over 0…21 mA
0.32 μA/cnt
Output current terminal 0 mA output until communication established
4…20 mA user configurable
0…20 mA user configurable
Absolute accuracy(1) current
terminal, min
(1) Includes offset, gain, non-linearity and repeatability error terms.
0.4% (0.1% if calibrated)
Accuracy drift w/temperature
current terminal <50 ppm/°C
Resistive load on mA output 0…750 Ω
Conversion type Digital to analog converter
Conversion rate 1 μs
Data format Signed integer
Calibration Factory calibrated
Step response to 63% of
value, max 160 μs
Surge current 2 A for 10 ms, repeatable every 3 s
Status indicators, logic side 1 green/red network status
1 green/red module status
4 green/red output status
IMPORTANT
Refer to Publication 1734-SG001 for information on breaking the field
power distribution bus. Refer to sections “When to Use the Field Power
Distributor” and “When to Use the Expansion Power Unit”.

18 POINT I/O 4 Channel Analog Current Output Module
Publication 1734-IN034C-EN-E - August 2016
General Specifications
Attribute Value
Module location 1734-TB or 1734-TBS wiring base assembly
POINTBus current, max 75 mA
Power dissipation, max 1.86 W @ 750 Ωon each output
2.15 W @ 0 Ωon each output
Thermal dissipation, max @
28.8V DC 6.34 BTU/hr @ 750 Ωload on each output 7.33 BTU/hr @ 0 Ωload on each channel
Supply voltage, backplane 5V DC
Supply voltage range, field
power input 10…28.8V DC (includes 5% AC ripple), 220 mA, Class 2
Output current 4…20 mA or 0…20 mA
Isolation voltage 50V, tested @ 1500V AC for 60 s, outputs and field power to system
No isolation between individual outputs or outputs to field power
External DC power supply
current, nom 110 mA @ 24V DC (including output @ 20 mA)
Dimensions (HxWxD), approx. 56.0 x 12.0 x 75.5 mm
(2.21 x 0.47 x 2.97 in.)
Keyswitch position 4
Enclosure type rating None (open-style)
Wire size 0.25…2.5 mm2(23…13 AWG) solid or stranded copper wire rated at
100 ° C (212 ° F), or greater, 1.2 mm (3/64 in.) insulation max
Wiring category(1) 2 – on signal ports
1 – on power ports
Wire type Shielded
Terminal base screw torque Determined by installed terminal block
Weight, approx. 36.9 g (1.3 oz)
North American temp code T4A
IEC temp code T4
(1) Use this conductor category information for planning conductor routing as described in Industrial Automation Wiring
and Grounding Guidelines, publication 1770-4.1.

POINT I/O 4 Channel Analog Current Output Module 19
Publication 1734-IN034C-EN-E - August 2016
Environmental Specifications
Attribute Value
Temperature, operating IEC 60068-2-1 (Test Ad, Operating Cold),
IEC 60068-2-2 (Test Bd, Operating Dry Heat),
IEC 60068-2-14 (Test Nb, Operating Thermal Shock):
-20…55 °C (-4…131 °F)
Temperature,
surrounding air, max. 55 °C (131 °F)
Temperature, nonoperating IEC 60068-2-1 (Test Ab, Unpackaged Nonoperating Cold),
IEC 60068-2-2 (Test Bb, Unpackaged Nonoperating Dry Heat),
IEC 60068-2-14 (Test Na, Unpackaged Nonoperating Thermal Shock):
-40…85 °C (-40…185 °F)
Relative humidity IEC 60068-2-30 (Test Db, Unpackaged Damp Heat):
5…95% noncondensing
Vibration IEC 60068-2-6, (Test Fc, Operating):
5 g @ 10…500 Hz
Shock, operating IEC 60068-2-27 (Test Ea, Unpackaged Shock):
30 g
Shock, nonoperating IEC 60068-2-27 (Test Ea, Unpackaged Shock):
50 g
Emissions CISPR 11
Group 1, Class A
ESD immunity IEC 61000-4-2:
6 kV contact discharges
8 kV air discharges
Radiated RF immunity IEC 61000-4-3:
10V/m with 1 kHz sine-wave 80%AM from 80 MHz…2000 MHz
10V/m with 200 Hz 50% pulse 100%AM @ 900 MHz
10V/m with 200 Hz 50% pulse 100%AM @ 1890 MHz
10V/m with 1 kHz sine-wave 80%AM from 2000…2700 MHz
EFT/B immunity IEC 61000-4-4:
±3 kV at 5 kHz on power ports
±3 kV at 5 kHz on signal ports
Surge transient immunity IEC 61000-4-5:
±1 kV line-line(DM) and ±2 kV line-earth(CM) on power ports
±2 kV line-earth(CM) on shielded ports
Conducted RF immunity IEC 61000-4-6:
10V rms with 1 kHz sine-wave 80%AM @ 150 kHz…80 MHz

20 POINT I/O 4 Channel Analog Current Output Module
Publication 1734-IN034C-EN-E - August 2016
Certifications
Certification (when
product is marked)
(1)
Value
c-UL-us UL Listed Industrial Control Equipment, certified for US and Canada. See
UL File E65584.
UL Listed for Class I, Division 2 Group A,B,C,D Hazardous Locations,
certified for U.S. and Canada. See UL File E194810
CE European Union 2014/30/EU EMC Directive, compliant with:
EN 61326-1; Meas./Control/Lab., Industrial Requirements
EN 61000-6-2; Industrial Immunity
EN 61000-6-4; Industrial Emissions
EN 61131-2; Programmable Controllers (Clause 8, Zone A & B)
Ex European Union 2014/34/EU ATEX Directive, compliant with:
EN 60079-15:2010; Potentially Explosive Atmospheres, Protection “n”
EN 60079-0:2012 + A11:2013; General Requirements
II 3 G Ex nA IIC T4 Gc
DEMKO 04 ATEX 0330347X
EAC Russian Customs Union TR CU 020/2011 EMC Technical Regulation
RCM Australian Radiocommunications Act, compliant with:
AS/NZS CISPR 11; Industrial Emissions
KC Korean Registration of Broadcasting and Communications Equipment,
compliant with:
Article 58-2 of Radio Waves Act, Clause 3
(1) See the Product Certification link at http://www.rockwellautomation.com/products/certification/ for Declaration of
Conformity, Certificates, and other certification details.