Allen-Bradley FLEX I/O 1794-IR8 User manual


  "  #!!   % $# #  $#  '  & 
   

(Cat. No. 1794-IR8)







 
This module mounts on a 1794 terminal base unit.
1. Rotate keyswitch (1) on terminal base unit (2) clockwise to position 3
as required for this type of module.
2. Make certain the flexbus connector (3) is pushed all the way to the left
to connect with the neighboring terminal base/adapter. You cannot
install the module unless the connector is fully extended.
3. Make sure that the pins on the bottom of the module are straight so
they will align properly with the connector in the terminal base unit.
4. Position the module (4) with its alignment bar (5) aligned with the
groove (6) on the terminal base.
5. Press firmly and evenly to seat the module in the terminal base unit.
The module is seated when the latching mechanism (7) is locked into
the module.
Installation Instructions
Allen-Bradley

24V dc FLEX I/O RTD Input Module2
    
!ATTENTION: Remove field-side power before
removing or inserting this module. This module is
designed so you can remove and insert it under
backplane power. When you remove or insert a module
with field-side power applied, an electrical arc may
occur. An electrical arc can cause personal injury or
property damage by:
•sending an erroneous signal to your system’s field
devices causing unintended machine motion
•causing an explosion in a hazardous environment
Repeated electrical arcing causes excessive wear to
contacts on both the module and its mating connector.
Worn contacts may create electrical resistance.
   
If this product has the CE mark it is approved for installation within the
European Union and EEA regions. It has been designed and tested to meet
the following directives.
EMC Directive
This product is tested to meet Council Directive 89/336/EEC
Electromagnetic Compatibility (EMC) and the following standards, in
whole or in part, documented in a technical construction file:
•EN 50081-2 EMC – Generic Emission Standard, Part 2 – Industrial
Environment
•EN 50082-2 EMC – Generic Immunity Standard, Part 2 – Industrial
Environment
This product is intended for use in an industrial environment.
Low Voltage Directive
This product is tested to meet Council Directive 73/23/EEC Low Voltage,
by applying the safety requirements of EN 61131–2 Programmable
Controllers, Part 2 – Equipment Requirements and Tests.
For specific information required by EN 61131-2, see the appropriate
sections in this publication, as well as the following Allen-Bradley
publications:
•Industrial Automation Wiring and Grounding Guidelines For Noise
Immunity, publication 1770-4.1
•Automation Systems Catalog, publication B111
This equipment is classified as open equipment and must be mounted in
an enclosure during operation to provide safety protection.

24V dc FLEX I/O RTD Input Module 3
Publication 1794Ć5.22 - May 1999

1. Connect the individual high and low signal wiring to numbered
terminals on the 0–15 row (A) on the terminal base unit as indicated
in the wiring table.
2. Connect 24V dc common to terminal 16 on row (B).
!ATTENTION: You must power this module from the same
power supply that supplies the adapter module so they both
power up or down together. You must cycle power for the
adapter to recognize this module.
3. Connect individual channel signal returns to the associated terminal
on row (B) as shown in the wiring table.
Important: Use the following Belden cables for connecting the RTD to
the terminal base unit:
        
2Ćwire Not applicable 9501
3Ćwire Less than 100ft (30.5 ) with nor al hu idity 9533
Over 100ft (30.5 )  high hu idity183503
1Greater than 55% for ore than 8 hours
4. Connect individual channel shield returns to the associated terminal
on row (B) for 1794-TB3 and -TB3S or row (C) for the 1794-TB3T or
-TB3TS as shown in the wiring table.
5. Connect +24V dc to terminal 34 on the 34-51 row (C).
ATTENTION: To reduce susceptibility to noise, power
analog modules and digital modules from separate power
supplies. Do not exceed a length of 33 ft (10m) for dc
power cabling.
ATTENTION: Do not daisy chain power or ground from
this terminal base unit to any ac or dc digital module
terminal base units.
6. If daisy-chaining 24V dc common, connect jumper from terminal 33
to terminal 16 on the next terminal base unit.
7. If daisy-chaining +24V dc, connect jumper from terminal 51 to
terminal 34 on the next terminal base unit.
Allen-Bradley

24V dc FLEX I/O RTD Input Module4
Publication 1794Ć5.22 - May 1999
8. Connect the shield to functional earth ground as near as possible to
the module.
ATTENTION: Total current draw through the terminal
base unit is limited to 10A. Separate power connections to
the terminal base unit may be necessary.
17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
16
12 34567891011121314150
35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51
34
1794ĆTB3, ĆTB3S, ĆTB3T
0 -15
34-51
16-33
A
B
C
RTD
1794ĆTB3 and ĆTB3S Te minal Base Units
RTD
Channel High Signal
Te minal Low Signal Te minal Signal Retu n1Shield Retu n
0 0 1 17 18
1 2 3 19 20
2 4 5 21 22
3 6 7 23 24
4 8 9 25 26
5 10 11 27 28
6 12 13 29 30
7 14 15 31 32
24V dc Common 16 thru 33
+24V dc power 34 thru 51
1When using a 2Ćwire RTD, umper the signal return to the low signal terminal.

24V dc FLEX I/O RTD Input Module 5
Pub ication 1794Ć5.22 - May 1999
RTD
1794ĆTB3T and ĆTB3TS Term nal Base Un ts
RTD
Channel H gh S gnal
Term nal Low S gnal Term nal S gnal Return Sh eld Return1
0 0 1 17 39
1 2 3 19 40
2 4 5 21 41
3 6 7 23 42
4 8 9 25 43
5 10 11 27 44
6 12 13 29 45
7 14 15 31 46
24V dc Common 16, 17, 19, 21, 23, 25, 27, 29, 31 and 33
+24V dc power 34 and 51
1Termina s 39 to 46 are chassis ground.
Example of 2Ć, 3Ć and 4Ćw re RTD W r ng to a 1794ĆTB3 Base Un t
17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
16
12 34567891011121314150
35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51
34
1794ĆTB3
0 -15
34-51
16-33
A
B
C
4ĆW re RTD 2ĆW re RTD3ĆW re RTD
C ip or tieback
4th ead.
Attent on: Keep exposed area of inner conductor as short as possib e.
Allen-Bradley

24V dc FLEX I/O RTD Input Module6
.'% -%)( 1  0 
Example of 2Ć, 3Ć and 4Ćw re RTD W r ng to a 1794ĆTB3T Base Un t
                
               

 
                

1794ĆTB3T
0 -15
34-51
16-33
A
B
C
3ĆW re RTD 2ĆW re RTD
4ĆW re RTD
'%* )+ -%" &
-$ '"!
Attent on: ""* "/*),"! +" )# %(("+ )(!. -)+ , ,$)+- , *),,%'"
Ind cators
              
     
3


AB
+_+_+_+_+_+_+_+_
A= Status Indicator – indicates diagnostics results and
configuration status.
B= Insertable label for writing individual input designations.

24V dc FLEX I/O RTD Input Module 7
Publication 1794Ć5.22 - May 1999
Block Transfer Read and Write
The following block transfer read and write word bit information is
presented for experienced users only. Refer to the user manual
(publication 1794-6.5.4)for this product for complete information on
programming and configuring your module.
Read Words
Dec. Bit
Word 15 14 13 12 11 10 09 08 07 06 05 04 03 02 01 00
0 Reserved
1 Channel 0 Input Data
2 Channel 1 Input Data
3 Channel 2 Input Data
4 Channel 3 Input Data
5 Channel 4 Input Data
6 Channel 5 Input Data
7 Channel 6 Input Data
8 Channel 7 Input Data
9 Overrange Bits Underrange Bits
10 0 0 0 0 0 Bad
Cal
Cal
Dne
Cal
Rng RIUP Critical Error Bits
Pwr
Up Res. 0 0
Write Words
Dec. Bit
Word 15 14 13 12 11 10 09 08 07 06 05 04 03 02 01 00
0 8Ćbit Calibration Mask Cal
Clk
Cal
Hi
Cal
Lo
Filter Cutoff Enh MDT
1RTD3Type RTD2Type RTD1Type RTD0Type
2RTD7Type RTD6Type RTD5Type RTD4Type
here: Enh = Enhanced mode
MDT = Module data type
Allen-Bradley

24V dc FLEX I/O RTD Input Module8
Pu lication 1794Ć5.22 - May 1999
Data Type
Word Description
Write word
0
Module Data Type
0
01 00 Bits
0 0 oC (default)
0 1 oF
1 0 Bipolar counts scaled etween -32768 and +32767
1 1 Unipolar counts scaled etween 0 and 65535
RTD Type
Word Description
RTD Type - Range
Write Word 1 Bit 03 02 01 00 Channel 0
0 0 0 0 Resistance (default)
0 0 0 1 No sensor connected - do not scan
0 0 1 0 100 ohm Pt α = 0.00385 Euro (-200 to +870oC)
0 0 1 1 100 ohm Pt α = 0.003916 U.S. (-200 to +630oC)
0 1 0 0 200 ohm Pt α = 0.00385 Euro (-200 to +630oC)
0 1 0 1 500 ohm Pt α = 0.00385 Euro (-200 to +630oC)
0 1 1 0 Reserved
0 1 1 1 10 ohm Copper (-200 to +260oC)
1 0 0 0 120 ohm Nickel (-60 to +250oC)
1 0 0 1 100 ohm Nickel (-60 to +250oC)
1 0 1 0 200 ohm Nickel (-60 to +250oC)
1 0 1 1 500 ohm Nickel (-60 to +250oC)
1 1 0 0 Reserved

24V dc FLEX I/O RTD Input Module 9
#" &  % 
   
 "   
"#
"        ! "!  $  
"#
       ! "!  $  
       ! "!  $  
 "    "        ! "!  $  
       ! "!  $  
       ! "!  $  
       ! "!  $  
Allen-Bradley

24V dc FLEX I/O RTD Input Module10
Publication 1794Ć5.22 - May 1999
   
CSAcertifies products for general use as well as for use in azardous locations. 
        as s own below, and not by
statements in any user documentation.
Example of t e CSA certification product label

To comply wit CSA certification for use in azardous locations, t e following information
becomes a part of t e product literature for CSAĆcertified AllenĆBradley industrial control
products.
•T is equipment is suitable for use in Class I, Division 2,
Groups A, B, C, D, or nonĆ azardous locations only.
•T e products aving t e appropriate CSA markings (t at is, Class I Division 2, Groups
A, B, C, D), are certified for use in ot er equipment w ere t e suitability of combination
(t at is, application or use) is determined by t e CSA or t e local inspection office
aving jurisdiction.
 Due to t e modular nature of a PLCcontrol system, t e product wit t e
ig est temperature rating determines t e overall temperature code rating of a PLC
control system in a Class I, Division 2 location. T e temperature code rating is marked on
t e product label as s own.
Temperature code rating
Look for temperature code
rating ere

T e following warnings apply to products aving CSA certification for use in azardous
locations.