allgood Modric 2470 User manual

DO NOT install this product in areas where the
following may be present or occur:
• Corrosive or flammable gases, liquids or vapours.
• Ambient temperatures higher than 40ºC or less
than -5ºC.
• Possible obstructions which would hinder the
access or removal of the hand dryer.
P.04 Allgood plc, 297 Euston Road, London, NW1 3AQ www.allgood.co.ukAllgood plc, 297 Euston Road, London, NW1 3AQ www.allgood.co.uk P.01
Safety and guidance notes
A. All wiring to be in accordance with
the current I.E.E. Regulations, or the
appropriate standards of your
country and MUST be installed by a
suitably qualified person.
B. The Hand Dryer should be provided
with a local isolator switch capable
of disconnecting all poles, having a
contact separation of at least 3mm.
C. Ensure that mains supply (Voltage,
Frequency, and Phase) complies
with the rating label.
D. The Hand Dryer should only be used
in conjunction with fixed wiring.
E. The Hand Dryer should not be
used where it is liable to be subject
to direct water spray for prolonged
periods of time.
F. This appliance can be used by
children aged 8 and above and
persons with reduced physical,
sensory or mental capabilities or
lack of experience and knowledge
if they have been given supervision
or instruction concerning use of the
appliance in a safe way and
understand the hazards involved.
Children should be supervised to
ensure that they do not play with
the appliance.Cleaning and user
maintenance shall not be made by
children without supervision.
H. Stationary appliances not fitted with
means for disconnection from the
supply mains having a contact
separation in all poles that provide
full disconnection under over
voltage category III, the instructions
state that means for disconnection
must be incorporated in the fixed
wiring in accordance with the
wiring rules.
3
Servicing instructions
The minimum service period for the
2470 panel should be every 3 months
or more frequent intervals as experience
dictates:
1. Isolate the Hand Dryer unit from the
electricity supply before servicing.
2. Remove dust, fluff and any other
build up of foreign matter from
inlet and outlet grille areas
(Illustration 3).
ORIGINAL FIXING INSTRUCTIONS
Modric 2470 flush mounted hand dryer
ORIGINAL FIXING INSTRUCTIONS
Modric 2470 flush mounted hand dryer
IMPORTANT
Read these instructions before
commencing with the installation.
IMPORTANT
After installation or servicing, units must be checked,
and only left when electrically and mechanically safe.

P.02 P.03
ORIGINAL FIXING INSTRUCTIONS
Modric 2470 flush mounted hand dryer
ORIGINAL FIXING INSTRUCTIONS
Modric 2470 flush mounted hand dryer
Mounting instructions
The aperture required in the wall
to mount the 2470 unit is 458mm
(H) x 318mm (W) x 105mm (D), see
Illustration 1. The distance from finished
floor level to the bottom of the aperture
is as follows:-
• Male washrooms 1028mm
• Female washrooms 978mm
• Disabled washrooms 876mm
• Children aged 14-17 978mm
• Children aged 11-13 876mm
• Children aged 8-10 774mm
• Children aged 4-7 672mm
To install the 2470 unit please follow
the steps below and outlined in
Illustration 2:
1. Create an aperture in the wall to
the dimensions outlined in the
Mounting Instructions (Page 2).
2. Unattach the fascia of the 2470
unit by unclicking the back of the
2 hinges positioned in the right
hand side of the back box.
3. Unscrew the cover of the hand dryer
and the unit itself and take out of
the back box.
Wiring instructions
Always ensure that the installation
conforms to the current edition of
the I.E.E. wiring regulations, BS 7671
(UK) or the appropriate standards in
your country. Ensure that the unit is
separately fused with a suitably rated
fuse and that it is connected to the
supply with a double pole isolating
switch having a contact separation of
at least 3mm. Care should be taken
that single insulated conductors
cannot come into contact with the
mounting surface.
4. Offer the back box into the aperture
in the wall and fix it in place
through the holes on the side and
back of the back box.
5. Locate the hand dryer unit into the
back box and connect the wiring to
the unit as outlined in the Wiring
Instructions (Page 2). Reattach the
fascia by re-clicking the hinges back
in to position.
6. Close the fascia panel and using the
2450K key provided, lock the panel
closed via the lock positioned in
the hand dryer chute.
12
Allgood plc, 297 Euston Road, London, NW1 3AQ www.allgood.co.ukAllgood plc, 297 Euston Road, London, NW1 3AQ www.allgood.co.uk
318
458
WARNING
The hand dryer MUST be isolated from the power
supply during installation or maintenance.
IMPORTANT
After installation or servicing, units must be checked,
and only left when electrically and mechanically safe.