AllwinTech OneInGate 111 User manual

1
OneInGate 111 VoIP Router
Quick Install Guide
Version: 0.9.6(draft)
Document number: QIG-OneIn120-0.96
Date Issued by 09/21/2004

2
Table of contents
Chapter 1 Introducing OneInGate 120 VoIP Router.......................................................................3
1.1 Key Features .......................................................................................................................3
1.2 Specifications .....................................................................................................................3
Chapter 2 Getting Started................................................................................................................5
2.1 Identifying External Components................................................................................... 5
2.2 Installation.........................................................................................................................6
Chapter 3 Configuration ..............................................................................................................7
3.1 Connection ......................................................................................................................... 8
3.2 System status................................................................................................................... 10
3.3 VoIP Call Out................................................................................................................... 11
Chapter 4 VoIP Router Setting .................................................................................................. 13
4.1 VPN point-to-point VoIP phone environment setting ..............................................13
4.2 Installation plan........................................................................................................ 13
4.3 VPN Point-to-point VoIP phone construction.......................................................... 14
On net call: .......................................................................................................................14
4.4 Setting Procedure .....................................................................................................15

3
Chapter 1 Introducing OneInGate 120 VoIP Router
1.1 Key Features
VoIP
zSupport 2 simultaneous VoIP calls
zSupport T.38 FAX relay
zSupport QoS for VoIP
zCompliant with H.323 standard
zBuild in Web call Server function
zExtensible by external IVR/CDR/Billing servers for value- added application
zSupport Alternate gatekeepers
zSupport worldwide off net call by ITSP service
zSupport Multiple dialing plan / Call hunting group
zAdaptive Jitter Buffer function
zMultiple call profile for adjust VAD, Audio CODEC, H.245
tunneling, DTMF In/Out band, FAX relay, Frame Size, Q.931
Fast start parameters
Router
zSupport static and dynamic IP from DHCP, PPPoE
zBuilt-in DHCP Server
zSupport TCP/UDP Port Mapping (Local Server Mapping)
zSupport User-definable Static Routing Table
zSupport Network Access Rules (LAN-to-WAN & WAN-to-LAN)
zSelf-Protection against DoS Attacks
zDynamic DNS Support
1.2 Specifications
zPhysical: 214 X 147 X 32 mm
zPower: 12V DC, 1A(Max.) Adaptor
zWeight: 450 g
zWAN: 10/100Mbps RJ-45 connector, auto-sensing
zLAN: 4-port 10/100Mbps Ethernet Switch. (Auto MDI-II/MDI-X)
zVoIP: 2 SLIC(FXS) connect to phone sets

4
zLED Indicators : Power, Status, WAN linking , 4X LAN linking, Phone 1, phone 2
zSupported Protocol: UDP, TCP, Standard H.323, NAT,BOOTP, TFTP, FTP, HTTP, TELNET,
IEEE 802.3/ IEEE 802.3u
zSelectable Coders: G.711, G.723.1, G.726, G.729A
zDTMF / Call progress tone detection and generation
zG.168 echo cancellation
z1 Reset button for load factory default IP parameters setting
zUser friendly Web configure interface
zConfiguration/Upgrade by FTP and Web
zBuild-in watching dog for auto recovery

5
Chapter 2 Getting Started
2.1 Identifying External Components
Front Panel
Message: Flash light means GW booting OK
Ready: Constant light means VOIP service OK
Line: The PSTN line is in use.
VOIP: The VoIP line is in use
Status: The server registers status
Rear Panel
(Figure2-2)
12V: For the included power adapter. Be sure to use only the 12VDC power adapter included
with the product. Using the wrong power adapter can damage the product and void the
warranty.
Phone: Normal RJ-11 phone jacks used to connect analog telephones and fax machines.
Line: Normal RJ-11 phone jacks used to connect analog phone line or landline.
Reset: Clear all settings and restore them to the initial values present when the device was
purchased. After performing the reset, make sure to redefine the IP settings for the device in
the ‘Connection’.
LAN 1~3: A 10/100 dual-speed Ethernet port fitted with an RJ-45 connector used to connect
the VoIP gateway to a LAN device.
WAN : A 10/100 dual-speed Ethernet port fitted with an RJ-45 connector used to connect the
VoIP gateway to WAN device (usually a router).

6
2.2 Installation
Do not place heavy objects on the Router. Placing the Router in a well ventilated area is very
important. Not doing so may cause damage to the unit.
(Figure2-3)

7
Chapter 3 Configuration
The default setting of DHCP Server inside OneInGate120 VoIP Router is turn ON, So please set up
your PC TCP/IP network as “Get IP Automatically” from DHCP to get internal IP from
OneInGate120. By default, The OneInGate120 will become the network gateway and default IP is
192.168.1.1 and will assign your PC IP as 192.168.1.X.
Please go to “Control Panel” ”Network”. In the “Configure” page, choose the TCP/IP→of LAN card,
and press “Properties” please choose “Obtain IP Address Automatically”
Launch your browser and open the OneInGate120 Internal UI WAP page as
http://192.168.22.1/admin.
(Figure3-1)
The default User name is voip
The default Password is 1234

8
3.1 Connection
Click “Connection” option below “System Setup” item:
( Figure3-2)
Please select the type of Internet connection you have and set up the router to use the IP
Address Automatically, Static-IP or PPPoE ADSL connection.
If your ISP has not given you an IP address, select Obtain an IP Address Automatically
(default). If you have been given a specific IP address, select Specify an IP Address.
(Figure3-3)
To use Static-IP ADSL connection, please select “Specify an IP Address” and enter WAN IP
settings, including the Primary and Secondary DNS IPs, supplied by your ISP.

9
(Figure3-4)
To use PPPoE ADSL connection, please select Yes in use “PPPoE” ADSL service and
enter the “username” and “password” in the PPPoE setup section. Most of ADSL ISPs
assign dynamic-IP settings to the router when using PPPoE. Please select Obtain IP Address
Automatically(default setting). You can leave the Primary and Secondary DNS IP settings in
default. The router automatically obtains these settings from your ISP when the PPPoE
connection is successfully established.
(Figure3-5)

10
3.2 System status
“System Setup” →”System status” to check system status.
(Figure3-6)