Alpha Communications RD-GB2/A User manual

USER MANUAL
AWD260 REV. 12/2017
RD-GB2/A
GB2 Bus
Amplifier/
Repeater
TECHNOLOGY
42 Central Drive | Farmingdale NY 11735-1202
P: 631-777-5500 | F: 631-777-5599
Toll-Free: 1-800-666-4800
http://www.alphacommunications.com/

INTRODUCTION
First and foremost we would like to thank you for purchasing this product.
Our commitment to achieving the satisfaction of customers like you is manifested through our ISO-9001 certification
and the manufacture of products like the one you have just purchased.
Its advanced technology and strict quality control will ensure that customers and users enjoy the numerous features
that this device offers. To get the most out of them and ensure proper operation from day one, we recommend that you
read this instruction manual.
CONTENTS
2
SET-UP WARNINGS
-Do not overtighten the screws on the RD-GB2Abus amplifier module connector.
-Before connecting the device, check the connections between the power supply unit, door panel, distributors, GSM
interface, monitors, telephones and hands-free audio terminals.
-Use the Golmar cable (2x1mm ).RAP-2150 2
-Always follow the instructions contained in this manual.
RD-GB2A BUS AMPLIFIER
Introduction...................................................................................................................................................................2.
Contents....................................................................................................................................................................... 2.
Set-up warnings................................................................................................................................ 2.............................
Safety precautions.............................................................................................................................. .............. 2............ .
Characteristics..............................................................................................................................................................3.
RAP-2150 cable characteristics (Golmar).................................................................................... .............. 3................... .
Operating modes............................................................................................................................................ .................
...........................................................................................................................................................4.
Repeater mode
...............................................................................................................................................................5.Router mode
........................................................................................................................................................... 6.Gateway mode
Description of the RD-GB2ABus amplifier module........................................................................................... ................
.................................................................................................................................................................7.
Description
Installation........................................................................................................................................................................
.............................................................................. ............7.. .
Illustration of RD-GB2ABus amplifier module installation
........................................................................................ .....8-9................................... .Description of the DIP switches
.............................................................................................. .................................. 9.... .Description of the status LEDs
......................................................................................... ................ 9-10................ .Description of the function buttons
................... ................. 11-16... .Door panel call addresses and monitor addresses assigned to each RD-GB2A module
.....
...................................................... ..... 17-20.................. .
Configuring the button code (up to 32 addresses/apartments)
.................................................... ..... 21-30.................. .Configuring the button code (up to 128 addresses/apartments)
Wiring diagrams................................................................................................................................................ ...............
..................... 31.
Installation of a video door entry system with the RD-GB2Amodule 'repeater' mode of the monitor bus
.................32.Installation of a video door entry system with the RD-GB2Amodule 'repeater' mode of the door panel bus
.............. ...... 33...... .Installation of a video door entry system with RD-GB2Amodule 'router' mode (button/coded panel)
..................... 34.Installation of a video door entry system with RD-GB2A module 'gateway' mode (interior button panel)
..................... 35.Installation of a video door entry system with RD-GB2A module 'gateway' mode (interior coded panel)
................................................................................... 36.Installation of a video door entry system with 3 access panels
..................................................................................... ........37........... .Connection of Golmar DC and AC lock releases
SAFETY PRECAUTIONS
-.Always disconnect the power supply before installing or making modifications to the device
-.The fitting and handling of this device must be carried out by authorised personnel
-The wiring must run at least 40 cm away from any other wiring.
-Install the RD-GB2Amodule in a dry protected location free from the risk of dripping or splashing water.
-Install the RD-GB2Amodule with an FA-GB2A power supply.
-Avoid locations that are humid, dusty or near heat sources.
-Ensure that the air vents are free from obstruction so that air can circulate freely.
-To prevent damage, the RD-GB2Amodule must be firmly secured in place.

3
CHARACTERISTICS
RD-GB2A BUS AMPLIFIER
-RD-GB2ABus amplifier module with simplified wiring (non-polarised 2-wire bus).
-RD-GB2ABus amplifier module for the GB2 system that allows the following operating modes:
wRepeater mode, enables the distance of the door panel bus or monitor bus to be increased when it exceeds 80 m
(distance with Golmar RAP-2150 2x1mm twisted pair cable).
2
wRouter mode, enables the installation to have 8 risers/verticals.
wGateway mode, enables an installation with one general entrance door panel and 8 buildings with interior door panels.
-In repeater mode:
wEnables door panel bus or monitor bus distance to be increased when it exceeds 80m.
(Distance with Golmar RAP-2150 twisted pair 2x1mm cable).
2
wThe RD-GB2A module cannot be used as a repeater in installations with risers/verticals or general entrance door
panels.
wOnly one RD-GB2Amodule as repeater per installation.
-In router mode, enables the installation to have 8 risers/verticals:
wUp to 23 monitors and apartments with a Vesta2 monitor per riser. (Mixed inst with telephones max. 23 elements)..
w
wUp to 18 monitors and apartments with a Vesta7 monitor per riser. (Mixed inst with telephones max. 18 elements)..
wUp to 32 telephones and apartments with T562/Nhea telephones per riser (audio door entry system inst , audio only)..
wAn RD-GB2Amodule is required with FA-GB2A power supply for each riser/column.
wUp to 4 coded access panels with button access panels, see below:
-Installation with 1 door panel with pushbuttons up to 128 apartments (double button)/71 apartments (single button).
-Installation with 2 door panels with pushbuttons up to 64 apartments (double button)/31 apartments (single
button) on each door panel.
-Installation with 3 door panels with pushbuttons up to 42 apartments (double button)/21 apartments (single
button) on each door panel.
-Installation with 4 door panels with pushbuttons up to 32 apartments (double button)/16 apartments (single
button) on each door panel.
wThe door panel(s) must have an EL632 GB2Asound module installed for compatibility with this operating mode.
-In gateway mode, enables a system with one general entrance door panel and up to 8 interior buildings.
wUp to 23 monitors and apartments with a Vesta2 monitor per interior building. (Mixed installations with telephones
max. 23 elements).
wUp to 18 monitors and apartments with a Vesta7 monitor per interior building. (Mixed installations with telephones
max. 18 elements).
wUp to 32 telephones and apartments with T562/Nhea telephones per interior building (audio door entry system
installation, audio only).
wUp to 3 access door panels per interior building.
wUp to 1 general entrance door panel. (Note: To connect more than one general entrance door panel, consult
our technical service department).
wUp to 8 interior buildings (each interior building up to 3 access panels).
wAn RD-GB2Amodule is required with FA-GB2A power supply for each interior building.
wThe door panel(s) must have an EL632 GB2Asound module installed for compatibility with this operating mode.
-Each RD-GB2Amodule requires an FA-GB2A power supply.
-It is necessary to configure the operating mode.
-DIP switches (operating mode, RD-GB2Amodule address number and end of line).
-Status LEDs.
Electrical resistance of the conductor at 20°C
ELECTRICAL CHARACTERISTICS
19.5 /Km
Capacity between conductors
Characteristic impedance
VALUES
CONSTRUCTION CHARACTERISTICS
Class V
VALUES
Flexible 1mm twisted pair polished copper conductor
2
45pf/m 10%
100 10%
RAP-2150 (GOLMAR) CABLE CHARACTERISTICS
15 /mV
Wiring

RD-GB2A BUS AMPLIFIER
4
-This operating mode enables the distance of the door panel bus or monitor bus to be increased when it exceeds 80 m
(distance with Golmar RAP-2150 2x1mm twisted pair cable).
2
-The RD-GB2Amodule requires an FA-GB2A power supply.
-Install the RD-GB2Amodule with an FA-GB2A power supply.
-The RD-GB2A module cannot be used as a repeater in installations with risers/verticals or general entrance door
panels.
-Only one RD-GB2Amodule as repeater per installation.
OPERATING MODES
'Repeater' operating mode:
Twisted pair 2x0.75mm2
RAP-2150 (twisted pair 2x1mm )
2
60m
A
60m
B
1m
A1
80m 80m 1m
Cable
60m
B1
80m
D2L- 2GB
A
C
B
C
D
VESTA2
FA- 2GB /A
VESTA2
G 2B Building installation
D2L- 2GB
A1
C
B1
C
VESTA2
FA- 2GB /A
VESTA2
GB2 Building installation
with RD-GB2A on monitor bus
A
D
FA- 2GB /A
RD-GB2A
B
30m
C
40m
10m
D
15m
*
( )
*
( ) Distances with Golmar cable (twisted pair 2x1mm ).RAP-2150 2
D2L- 2GB
A1
C
B
C
VESTA2 VESTA2
GB2 Building installation
with RD-GB2A on door panel bus
A
D
FA- 2GB /A
FA-GB2/A
B1
RD-GB2A
Distances and cross-sections
M busonitor
Door panel bus
M busonitor
Door panel bus
M busonitor
Door panel bus
E 632 GB2AL
building mode
E 632 GB2AL
building mode
E 632 GB2AL
building mode
Repeater
mode Repeater
mode
IMPORTANT: For description, installation, configuration and programming of door panels and monitors, see the
corresponding manuals.

RD-GB2A BUS AMPLIFIER
5
-This operating mode enables the installation to have up to 8 risers/verticals.
-One RD-GB2Amodule per riser/column.
wUp to 23 monitors and apartments with a Vesta2 monitor per riser. (Mixed inst with telephones max. 23 elements)..
wUp to 18 monitors and apartments with a Vesta7 monitor per riser. (Mixed inst with telephones max. 18 elements)..
wUp to 32 telephones and apartments with T562/Nhea telephones per riser (audio door entry system installation,
audio only).
-An RD-GB2Amodule is required with FA-GB2A power supply for each riser/column.
-Install the RD-GB2Amodule with an FA-GB2A power supply.
-The door panel(s) must have an EL632 GB2Asound module installed for compatibility with this operating mode.
-Up to 4 coded access panels with button access panels, see below:
wInstallation with 1 door panel with pushbuttons up to 128 apartments (double button)/72 apartments (single button).
wInstallation with 2 door panels with pushbuttons up to 62 apartments (double button)/31 apartments (single button) on
each door panel.
wInstallation with 3 door panels with pushbuttons up to 42 apartments (double button)/21 apartments (single button) on
each door panel.
wInstallation with 4 door panels with pushbuttons up to 32 apartments (double button)/16 apartments (single button) on
each door panel.
OPERATING MODES
'Router' operating mode:
FA- 2GB /A
FA- 2GB /A
D2L- 2GB VESTA2
A1
12 Vdc / 270mA
E 632 GB2AL
Router mode
RD-GB2A
Nº 8
VESTA2
FA- 2GB /A
D2L- 2GB VESTA2
A1
VESTA2
FA- 2GB /A
D2L- 2GB VESTA2
A1
VESTA2
D2L- 2GB VESTA2VESTA2 D2L- 2GB VESTA2VESTA2 D2L- 2GB VESTA2VESTA2
A
D
C C
C C
C C
C C
C C
C C
B1B1B1
Stairway 1Stairway 2Stairway 8
Technical room
Twisted pair 2x0.75mm2
RAP-2150 (twisted pair 2x1mm )
2
60m
A
60m
B
1m
A1
80m 80m 1m
Cable
60m
B1
80m
30m
C
40m
10m
D
15m
*
( )
*
( ) Distances with Golmar cable (twisted pair 2x1mm ).RAP-2150 2
Distances and cross-sections
B
1
( ) It is recommended to install the RD-GB2A amplifiers and their respective FA-GB2A power supplies in a technical room.
Connection between RD-GB2A amplifiers with a distance of 20cm.
RD-GB2A
Nº 2
RD-GB2A
Nº 1
1
( )
R modeouter outerR mode outerR
mode
IMPORTANT:
-For description, installation, configuration and programming of door panels and monitors, see the corresponding manuals.

RD-GB2A BUS AMPLIFIER
6
-This operating mode enables a system with one general entrance door panel and up to 8 interior buildings.
-One RD-GB2Aamplifier per interior building.
wUp to 23 monitors and apartments with a Vesta2 monitor per interior building. (Mixed installations with telephones
max. 23 elements).
wUp to 18 monitors and apartments with a Vesta7 monitor per interior building. (Mixed installations with telephones
max. 18 elements).
wUp to 32 telephones and apartments with T562/Nhea telephones per interior building (audio door entry system
installation, audio only).
-An RD-GB2Amodule is required with FA-GB2A power supply for each interior building.
-Install the RD-GB2Amodule with an FA-GB2A power supply.
-The door panel must have an EL632 GB2Asound module installed for compatibility with this operating mode.
-Up to one general entrance door panel. (Note: To connect more than one general entrance door panel, consult
our technical service department).
-Up to 8 interior buildings (each interior building up to 3 access panels).
OPERATING MODES
'Gateway' operating mode:
FA- 2GB /A
FA- 2GB /A
D2L- 2GB VESTA2
A1
12 Vdc/
270mA
RD-GB2A
Nº 8
VESTA2
FA- 2GB /A
D2L- 2GB VESTA2
A1
VESTA2
FA- 2GB /A
D2L- 2GB VESTA2
A1
VESTA2
D2L- 2GB VESTA2VESTA2 D2L- 2GB VESTA2VESTA2 D2L- 2GB VESTA2VESTA2
A
D
C C
C C
C C
C C
C C
C C
B1B1B1
Interior building 1Interior building 2Interior building 8
Technical room
B
RD-GB2A
Nº 2
RD-GB2A
Nº 1
1
( )
12 Vdc/
270mA
E
D
12 Vdc/
270mA
E
D
12 Vdc/
270mA
E
D
Twisted pair 2x0.75mm2
RAP-2150 (twisted pair 2x1mm )
2
60m
A
60m
B
1m
A1
80m 80m 1m
Cable
60m
B1
80m
30m
C
40m
10m
D
15m
*
( )
*
( ) Distances with Golmar cable (twisted pair 2x1mm ).RAP-2150 2
1
( ) It is recommended to install the RD-GB2A amplifiers and their respective FA-GB2A power supplies in a technical room.
Connection between RD-GB2A amplifiers with a distance of 20cm.
IMPORTANT:
For description, installation, configuration and programming of door panels and monitors, see the corresponding manuals.
Distances and cross-sections
60m
E
80m
EL632 GB2A
Gateway mode
general
panel
EL632 GB2A
Building mode
interior
panel
EL632 GB2A
Building mode
interior
panel
EL632 GB2A
Building mode
interior
panel
G modeateway atewayG mode atewayG
mode

RD-GB2A BUS AMPLIFIER
7
DESCRIPTION OF THE RD-GB2A BUS AMPLIFIER MODULE
Description:
Model: RD-GB2/A
Bus-IN Bus-OUT
Tx/Rx In-Use
PA PB
NoRoute Amp-ON
123
ON
DIP
456
OUT DS IN IN
FRONT TOP
BOTTOM
a.
b.
c.
d.
Status LEDs.
Configuration buttons
Configuration DIP switch.
Output terminals from the amplifier to the bus.
Interior door panel connection terminals
(general entrance door panel system).
DIN rail latch release.
Bus input terminals.
e.
f.
g.
The RD-GB2A module can be mounted onto a
DIN rail (4 elements) by applying slight pressure.
To remove the RD-GB2A module from the DIN
rail, use a flat screwdriver to lever it off, as shown
in the drawing.
Install the RD-GB2A module in a dry protected location free from the risk of dripping or splashing water.
DIN 46277
Install the RD-GB2A module with an FA-GB2A power supply.
INSTALLATION
Illustration of RD-GB2A Bus amplifier module installation:
ab
d
a
eg
c
f
b
Model: RD-GB2/A
Bus-IN Bus-OUT
Tx/Rx In-Use
PA PB
NoRoute Amp-ON

RD-GB2A BUS AMPLIFIER
8
INSTALLATION
The DIP switches of the RD-GB2A module enable configuration of one of the 3 operating modes, module address
number and end of line.
-Repeater mode enables door panel bus or monitor bus distance to be increased when it exceeds 80 m.
-Router mode enables the installation to have up to 8 risers/columns.
-Gateway mode, enables an installation with one general entrance door panel and 7 buildings with interior door panels.
Description of the DIP switches:
1 2 3
ON
DIP
4 5 6
Configuring the operating mode:
Repeater mode:
DIP switches: 1 and 2 set to OFF.
*
( )
1 2 3
ON
DIP
4 5 6
Router mode:
DIP switches: 1 set to ON and 2 set to OFF.
1 2 3
ON
DIP
4 5 6
Gateway mode:
DIP switches: 1 set to OFF and 2 set to ON.
1 2 3
ON
DIP
4 5 6
No function.
1 2 3
ON
DIP
4 5 6
Configuring the address number on the RD-GB2A module installed:
To configure the RD-GB2A module as No. 1: DIP switches 3, 4 and 5 set to OFF.
-Button panel call addresses (0 to 31) for monitor address (0 to 31) respectively.
-Coded panel call addresses (1 to 32) for monitor address (0 to 31).
Note: Call address '32' on the coded panel calls the monitor with address '0'.
1 2 3
ON
DIP
4 5 6
To configure the RD-GB2A module as No. 2: DIP switch 3 set to ON, 4 and 5 set to OFF.
-Button panel call addresses (32 to 63) for monitor address (0 to 31) respectively.
-Coded panel call addresses (33 to 64) for monitor address (0 to 31).
Note: Call address '64' on the coded panel calls the monitor with address '0'.
1 2 3
ON
DIP
4 5 6
To configure the RD-GB2A module as No. 3: DIP switch 3 set to OFF, 4 set to ON and 5 set to OFF.
-Button panel call addresses (64 to 95) for monitor address (0 to 31) respectively.
-Coded panel call addresses (65 to 96) for monitor address (0 to 31).
Note: Call address '96' on the coded panel calls the monitor with address '0'.
1 2 3
ON
DIP
4 5 6
1 2 3
ON
DIP
4 5 6
To configure the RD-GB2A module as No. 5: DIP switches 3 and 4 set to OFF and 5 set to ON.
-Coded panel call addresses (129 to 160) for monitor address (0 to 31).
Note: Call address '160' on the coded panel calls the monitor with address '0'.
1 2 3
ON
DIP
4 5 6
To configure the RD-GB2A module as No. 6: DIP switch 3 set to ON, 4 set to OFF and 5 set to ON.
-Coded panel call addresses (161 to 192) for monitor address (0 to 31).
Note: Call address '192' on the coded panel calls the monitor with address '0'.
1 2 3
ON
DIP
4 5 6
To configure the RD-GB2A module as No. 7: DIP switch 3 set to OFF, 4 and 5 set to ON.
-Coded panel call addresses (193 to 224) for monitor address (0 to 31).
Note: Call address '224' on the coded panel calls the monitor with address '0'.
1 2 3
ON
DIP
4 5 6
To configure the RD-GB2A module as No. 4: DIP switches 3 and 4 set to ON and 5 set to OFF.
-Button panel call addresses (96 to 127) for monitor address (0 to 31) respectively.
-Coded panel call addresses (97 to 128) for monitor address (0 to 31).
Note: Call address '128' on the coded panel calls the monitor with address '0'.
To configure the RD-GB2A module as No. 8: DIP switches: 3, 4 and 5 set to ON.
-Coded panel call addresses (225 to 256) for monitor address (0 to 31).
Note: Call address '256' on the coded panel calls the monitor with address '0'.
*
( ) ( )
1
Continued overleaf
*
( ) Factory setting.
IMPORTANT:
-Select a different address number for each RD-GB2Amodule.
-Each address number of the RD-GB2A has 32 different door panel call addresses assigned for each RD-GB2A
module addressed. For further details see pages 11-16.
( )
1
( )
1
( )
1
( )
1
( )
1
( )
1
( )
1
( )
1

RD-GB2A BUS AMPLIFIER
9
INSTALLATION
Continued from previous page.
*
( )
1 2 3
ON
DIP
4 5 6
Configuring the end of line on the RD-GB2A module:
To configure the end of line of the RD-GB2A module:
DIP switch 6: Set the RD-GB2A module where the Bus cable ends
(marked as 'IN' on the terminals) to ON.
1 2 3
ON
DIP
4 5 6
To configure the end of line of the RD-GB2A module:
DIP switch 6: Leave the intermediate modules in the OFF position.
IN IN
IN IN
*
( ) Factory setting.
Description of the status LEDs:
Model: RD-GB2/A
Bus-IN Bus-OUT
Tx/Rx In-Use NoRoute
Bus In:
LED on: When the bus cable is connected to the 'IN' terminal.
Bus-Out:
LED on: When the monitor bus of the RD-GB2A module is connected.
TX/RX:
LED blinking: When the door panel is in communication with an RD-GB2A module monitor.
In-Use:
LED off: When the RD-GB2A module is in standby.
The RD-GB2A module has the following status LEDs:
Description of the function buttons:
Displaying video gain:
Gai 1n
Gai 2n
Gai 3n
Gai 4n
Gai 5n
Gai 6n
ON OFF OFF
OFF ON OFF
ON ON OFF
OFF OFF ON
ON OFF ON
OFF ON ON
Bus-IN LED Bus-OUT LED Tx/Rx LED
( )
*
Video gain
Note: Gain level from 1 to 6, with 1 the minimum value and 6 the maximum.
Step 1: Press button on one of the monitors connected to the RD-GB2A module that requires
video gain adjustment; the 'In-Use' LED will illuminate.
Step 2: Press the 'NoRoute' button to show, through the status LEDs, the level of gain of the RD-GB2A
module; see table:
Model: RD-GB2/A
Bus-IN Bus-OUT
Tx/Rx In-Use NoRoute
To see the level of gain of the RD-GB2A module, press button on one of the monitors
connected to the RD-GB2A module to be displayed (the image of the door panel will be displayed
on the monitor). Note: The image should be displayed throughout the process.
Model: RD-GB2/A
Bus-OUT PA PB
NoRoute Amp-ON
Function
buttons
Status LEDS
*
( ) Factory setting.
Continued overleaf

RD-GB2A BUS AMPLIFIER
10
INSTALLATION
Adjusting video gain:
To adjust the gain of the RD-GB2A module, press button on one of the monitors connected to the RD-GB2A
module to be displayed (the image of the door panel will be displayed on the monitor). Note: The image should be
displayed throughout the process.
.
Step 1: Press button on one of the monitors connected to the RD-GB2A module that requires video gain
adjustment; the 'In-Use' LED will illuminate. (Note: RD-GB2A in gateway mode, establish communication with
the general entrance door panel).
Step 2: Press button PA or PB to reduce or increase the gain level of the RD-GB2A module respectively. The status
LEDs will indicate the modified gain level; see table:
Step 3: Then, to save the selected gain value, press the 'NoRoute' button for 3 seconds; the 'In-Use' LED will blink.
Step 4: Press the 'NoRoute' button again for 3 seconds until the LED illuminates. This indicates that the RD-GB2A
module is operating with the gain value set in the previous steps in 'fixed mode' (always).
Step 5: Check that the new gain value is correct. With the monitor video activated, press the 'NoRoute' button and check
that the status LEDs indicate the required gain value (see video gain table in step 2).
Note: Repeat the procedure (steps 1 to 5) until the RD-GB2Amodule is set to the required video gain
Ga n 1i
Ga n 2i
Ga n 3i
Ga n 4i
Ga n 5i
Ga n 6i
ON OFF OFF
OFF ON OFF
ON ON OFF
OFF OFF ON
ON OFF ON
OFF ON ON
Bus-IN LED Bus-OUT LED Tx/Rx LED
( )
*
Video gain
Continued from previous page.
Set the video gain to 'fixed' or 'automatic' mode:
The RD-GB2A module has 2 operating modes for setting gain:
Model: RD-GB2/A
Bus-OUT PA PB
NoRoute Amp-ON
Function
buttons
'Fixed' mode: The RD-GB2A module will always use the gain configured in the module.
Step 1: Press button on one of the monitors connected to the RD-GB2A module that requires
video gain adjustment; the 'In-Use' LED will illuminate. (Note: RD-GB2A in gateway mode,
establish communication with the general entrance door panel).
Step 2: Then press the 'NoRoute' button for 3 seconds and repeat this step until the 'In-Use' status LED
illuminates.
'Automatic' mode: The RD-GB2A module adjusts the gain automatically when it connects to the
system.
Step 1: Press button on one of the monitors connected to the RD-GB2A module that requires
adjustment to 'automatic' mode; the 'In-Use' LED will illuminate.
Step 2: Then press the 'NoRoute' button for 3 seconds and repeat this step until the 'In-Use' status LED
is blinking.
Default settings:
To use the default settings of the RD-GB2A module (level 1 gain and 'fixed' mode):
Step 1: Disconnect the module from the power supply.
Step 2: Reconnect the module to the power supply. Then, during the first 10 seconds, with the RD-GB2A
module in standby, press the 'NoRoute' button for 3 seconds; the 'In-Use' status LED will blink once
confirming that the module is now using the default settings.
Note: Gain level from 1 to 6, with 1 the minimum value and 6 the maximum.
*
( ) Factory setting.
Model: RD-GB2/A
Bus-IN Bus-OUT
Tx/Rx In-Use NoRoute
Status LEDS

RD-GB2A BUS AMPLIFIER
11
INSTALLATION
Door panel call addresses and monitor addresses assigned to each RD-GB2A module:
Button panel address
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
.
22
23
24
25
26
27
28
29
30
31
Button 'P1' EL632 GB2A module
Button 'P2' EL632 GB2A module
EL610D module No. 1..
"P2" (Add. 2)Button
"P3" (Add. 3)Button
"P4" 4(Add. )Button
"P5" 5(Add. )Button
"P6" 6(Add. )Button
"P7" 7(Add. )Button
"P8" 8(Add. )Button
"P9" 9(Add. )Button
"P10" 10(Add. )Button
"P1" 11(Add. )Button
2EL610D module No.
"P2" 12(Add. )Button
"P3" 13(Add. )Button
"P4" 14(Add. )Button
"P5" 15(Add. )Button
"P6" 16(Add. )Button
"P7" 17(Add. )Button
"P8" 18(Add. )Button
"P9" 19(Add. )Button
"P10" 0(Add. 2 )Button
"P1" 1(Add. 2 )Button
3EL610D module No.
"P2" 22(Add. )Button
"P3" 23(Add. )Button
"P4" 24(Add. )Button
"P5" 25(Add. )Button
"P6" 26(Add. )Button
"P7" 27(Add. )Button
"P8" 28(Add. )Button
"P9" 29(Add. )Button
"P10" 30(Add. )Button
"P1" 1(Add. 3 )Button
Monitor address
RD-GB2A module No. 1
Monitor address Coded panel address
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32 +
1 +
2 +
3 +
4 +
5 +
6 +
7 +
8 +
9 +
10 +
11 +
12 +
13 +
14 +
15 +
16 +
17 +
18 +
19 +
20 +
21 +
22 +
23 +
24 +
25 +
26 +
27 +
28 +
29 +
30 +
31 +
0
1
Button 'P1' EL632 GB2A module
Button 'P2' EL632 GB2A module
( )
*
23
IMPORTANT:
-In door panel systems with call buttons, the first address on the monitor is 'Code 0'.
-In coded panel systems (N3301/GB2), on , 'code 0' is 'code 32', which means that when a call isRD-GB2A module No. 1
made to a monitor with 'code 0' (DIP 1 to DIP 5 set to OFF), needs to be entered on the N3301/GB2 numeric
keypad.
-In the software (Address Manager GB2) of the EL632-GB2A module, button P1 with call 'code 0' is also shown as
'code 32'.
Continued overleaf
( )
*( ) *
( )
*
NOTE: For description, installation, configuration and programming of door panels and monitors, see the corresponding manuals.

RD-GB2A BUS AMPLIFIER
12
INSTALLATION
Continued from previous page.
Button panel address
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
EL610D module No. 4.
"P2" (Add. 32)Button
"P3" (Add. 33)Button
"P4" (Add. 34)Button
"P5" (Add. 35)Button
"P6" (Add. 36)Button
"P7" (Add. 37)Button
"P8" (Add. 38)Button
"P9" (Add. 39)Button
"P10" (Add. 40)Button
"P1" (Add. 41)Button
5EL610D module No.
"P2" (Add. 42)Button
"P3" (Add. 43)Button
"P4" (Add. 44)Button
"P5" (Add. 45)Button
"P6" (Add. 46)Button
"P7" (Add. 47)Button
"P8" (Add. 48)Button
"P9" (Add. 49)Button
"P10" (Add. 50)Button
"P1" (Add. 51)Button
6EL610D module No.
"P2" (Add. 52)Button
"P3" (Add. 53)Button
"P4" (Add. 54)Button
"P5" (Add. 55)Button
"P6" (Add. 56)Button
"P7" (Add. 57)Button
"P8" (Add. 58)Button
"P9" (Add. 59)Button
"P10" (Add. 60)Button
"P1" (Add. 61)Button
7EL610D module No.
"P2" 6(Add. 2)Button
"P3" 6(Add. 3)Button
Monitor address
RD-GB2A module No. 2
Monitor address Coded panel address
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
64 +
33 +
34 +
35 +
36 +
37 +
38 +
39 +
40 +
41 +
42 +
43 +
44 +
45 +
46 +
47 +
48 +
49 +
50 +
51 +
52 +
53 +
54 +
55 +
56 +
57 +
58 +
59 +
60 +
61 +
62 +
63 +
Continued overleaf
( )
*
46
IMPORTANT:
-In coded panel systems (N3301/GB2), on , to make a call to a monitor with 'code 0' (DIP 1 to DIPRD-GB2A module No. 2
5 set to OFF), needs to be entered on the N3301/GB2 numeric keypad.
NOTE: For description, installation, configuration and programming of door panels and monitors, see the corresponding manuals.
( )
*

RD-GB2A BUS AMPLIFIER
13
INSTALLATION
Continued from previous page.
Button panel address
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
7
EL610D module No.
"P4" 6(Add. 4)Button
"P5" 6(Add. 5)Button
"P6" 6(Add. 6)Button
"P7" 6(Add. 7)Button
"P8" 6(Add. 8)Button
"P9" 6(Add. 9)Button
"P10" 7(Add. 0)Button
"P1" 7(Add. 1)Button
8EL610D module No.
"P2" 7(Add. 2)Button
"P3" 7(Add. 3)Button
"P4" 7(Add. 4)Button
"P5" 7(Add. 5)Button
"P6" 7(Add. 6)Button
"P7" 7(Add. 7)Button
"P8" 7(Add. 8)Button
"P9" 7(Add. 9)Button
"P10" 8(Add. 0)Button
"P1" 8(Add. 1)Button
9EL610D module No.
"P2" 8(Add. 2)Button
"P3" 8(Add. 3)Button
"P4" 8(Add. 4)Button
"P5" 8(Add. 5)Button
"P6" 8(Add. 6)Button
"P7" 8(Add. 7)Button
"P8" 8(Add. 8)Button
"P9" 8(Add. 9)Button
"P10" 9(Add. 0)Button
"P1" 9(Add. 1)Button
10EL610D module No.
"P2" 9(Add. 2)Button
"P3" 9(Add. 3)Button
"P4" 94(Add. )Button
"P5" 95(Add. )Button
Monitor address
RD-GB2A module No. 3
Monitor address Coded panel address
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
96 +
65 +
66 +
67 +
68 +
69 +
70 +
71 +
72 +
73 +
74 +
75 +
76 +
77 +
78 +
79 +
80 +
81 +
82 +
83 +
84 +
85 +
86 +
87 +
88 +
89 +
90 +
91 +
92 +
93 +
94 +
95 +
Continued overleaf
( )
*
69
IMPORTANT:
-In coded panel systems (N3301/GB2), on , to make a call to a monitor with 'code 0' (DIP 1 to DIPRD-GB2A module No. 3
5 set to OFF), needs to be entered on the N3301/GB2 numeric keypad.
NOTE: For description, installation, configuration and programming of door panels and monitors, see the corresponding manuals.
( )
*

RD-GB2A BUS AMPLIFIER
14
INSTALLATION
Continued from previous page.
Button panel address
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
10
EL610D module No.
"P6" 9(Add. 6)Button
"P7" 9(Add. 7)Button
"P8" 9(Add. 8)Button
"P9" 9(Add. 9)Button
"P10" 10(Add. 0)Button
"P1" 10(Add. 1)Button
11EL610D module No.
"P2" 102(Add. )Button
"P3" 103(Add. )Button
"P4" 104(Add. )Button
"P5" 105(Add. )Button
"P6" 106(Add. )Button
"P7" 107(Add. )Button
"P8" 108(Add. )Button
"P9" 109(Add. )Button
"P10" 110(Add. )Button
"P1" 111(Add. )Button
12EL610D module No.
"P2" 112(Add. )Button
"P3" 113(Add. )Button
"P4" 114(Add. )Button
"P5" 115(Add. )Button
"P6" 116(Add. )Button
"P7" 117(Add. )Button
"P8" 118(Add. )Button
"P9" 119(Add. )Button
"P10" 120(Add. )Button
"P1" 12(Add. 1)Button
13EL610D module No.
"P2" 12(Add. 2)Button
"P3" 123(Add. )Button
"P4" 124(Add. )Button
"P5" 125(Add. )Button
"P6" 126(Add. )Button
"P7" 127(Add. )Button
Monitor address
RD-GB2A module No. 4
Monitor address Coded panel address
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
128 +
97 +
98 +
99 +
100 +
101 +
102 +
103 +
104 +
105 +
106 +
107 +
108 +
109 +
110 +
111 +
112 +
113 +
114 +
115 +
116 +
117 +
118 +
119 +
120 +
121 +
122 +
123 +
124 +
125 +
126 +
127 +
Continued overleaf
( )
*
82
IMPORTANT:
-In coded panel systems (N3301/GB2), on , to make a call to a monitor with 'code 0' (DIP 1 to DIPRD-GB2A module No. 4
5 set to OFF), needs to be entered on the N3301/GB2 numeric keypad.
1
NOTE: For description, installation, configuration and programming of door panels and monitors, see the corresponding manuals.
( )
*

RD-GB2A BUS AMPLIFIER
15
INSTALLATION
Continued from previous page.
RD-GB2A module No. 5
Monitor address Coded panel address
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
192 +
161 +
162 +
163 +
164 +
165 +
166 +
167 +
168 +
169 +
170 +
171 +
172 +
173 +
174 +
175 +
176 +
177 +
178 +
179 +
180 +
181 +
182 +
183 +
184 +
185 +
186 +
187 +
188 +
189 +
190 +
191 +
Monitor address Coded panel address
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
160 +
129 +
130 +
131 +
132 +
133 +
134 +
135 +
136 +
137 +
138 +
139 +
140 +
141 +
142 +
143 +
144 +
145 +
146 +
147 +
148 +
149 +
150 +
151 +
152 +
153 +
154 +
155 +
156 +
157 +
158 +
159 +
RD-GB2A module No. 6
( )
*
06
IMPORTANT:
-In coded panel systems (N3301/GB2), on , to make a call to a monitor with 'code 0' (DIP 1 toRD-GB2A module No. 5
DIP 5 set to OFF), needs to be entered on the N3301/GB2 numeric keypad.
-In coded panel systems (N3301/GB2), on , to make a call to a monitor with 'code 0' (DIP 1 toRD-GB2A module No. 6
DIP 5 set to OFF), needs to be entered on the N3301/GB2 numeric keypad.
1
Continued overleaf
291
NOTE: For description, installation, configuration and programming of door panels and monitors, see the corresponding manuals.
( )
*
( )
*

RD-GB2A BUS AMPLIFIER
16
INSTALLATION
Continued from previous page.
RD-GB2A module No. 7
Monitor address Coded panel addressMonitor address Coded panel address
RD-GB2A module No. 8
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
256 +
225 +
226 +
227 +
228 +
229 +
230 +
231 +
232 +
233 +
234 +
235 +
236 +
237 +
238 +
239 +
240 +
241 +
242 +
243 +
244 +
245 +
246 +
247 +
248 +
249 +
250 +
251 +
252 +
253 +
254 +
255 +
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
224 +
193 +
194 +
195 +
196 +
197 +
198 +
199 +
200 +
201 +
202 +
203 +
204 +
205 +
206 +
207 +
208 +
209 +
210 +
211 +
212 +
213 +
214 +
215 +
216 +
217 +
218 +
219 +
220 +
221 +
222 +
223 +
( )
*
42
IMPORTANT:
-In coded panel systems (N3301/GB2), on , to make a call to a monitor with 'code 0' (DIP 1 toRD-GB2A module No. 7
DIP 5 set to OFF), needs to be entered on the N3301/GB2 numeric keypad.
-In coded panel systems (N3301/GB2), on , to make a call to a monitor with 'code 0' (DIP 1 toRD-GB2A module No. 8
DIP 5 set to OFF), needs to be entered on the N3301/GB2 numeric keypad.
2
652
NOTE: For description, installation, configuration and programming of door panels and monitors, see the corresponding manuals.
( )
*
( )
*

17
The EL610D button module needs to be configured in order to assign a call
code to the buttons. Carry out this configuration with the DIP switch
located at the back of the module.
Depending on the configuration option selected, the buttons will be assigned
with a certain call code.
To configure the call code on the monitors. It is worth noting the call code
of each button, as shown in the table below.
Important: Select a different configuration option for each EL610D module.
P1- P10: Button 1 - button 10.
(1)
*
( ) Factory setting.
*
( )
Configuring the button code (up to 32 addresses/apartments)
EL610D button module
2
Dip1
1
3
Dip2 Dip3 Dip4 Dip5 Dip6 Dip7 Dip8
Module configuration option
P1
11
31
21
DIP switch
On
Off
Off
Off
Off
On
Off
On
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
On
On
On
Button code
P2 P3 P4 P5 P6 P7
2
22
12
3
23
13
4
24
14
5
25
15
6
26
16
7
27
17
8
28
18
9
29
19
10
30
20
P8 P9 P10 (1)
*
( )
2
Dip1
1
4
6
3
5
7
Dip2 Dip3 Dip4 Dip5 Dip6 Dip7 Dip8 P1
1
11
21
31
6
16
26
On
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
On
Off
Off
Off
On
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
On
Off
Off
Off
On
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
On
Off
Off
Off
On
Off
Off
Off
On
On
On
On
On
On
On
P3 P5 P7 P9
2
12
22
_
7
17
27
3
13
23
8
18
28
4
14
24
9
19
29
5
15
25
10
20
30
(1)
*
( )
Double button module codes
Single button module codes
_ _ _
IMPORTANTE:
For description, installation, configuration and programming of the door panel, EL610D module and monitors, see the
manuals supplied with the respective door panel and monitors.
RD-GB2A BUS AMPLIFIER
INSTALLATION

18
Configuring double button module codes:
EL632 GB2A
P1P2 P2
1 2 3 4 5 6 7 8
ON
9 10
78
56
34
12
1 2 3 4 5 6 7 8
ON
9 10
78
56
34
12
1 2 3 4 5 6 7 8
ON
9 10
78
56
34
12
EL610D
1 2 3
ON DIP
4 5 6
1 2 3
ON DIP
4 5 6
1 2 3
ON DIP
4 5 6123
ON DIP
4 5 6
1 2 3
ON DIP
4 5 6
1 2 3
ON DIP
4 5 6
1 2 3
ON DIP
4 5 6
123
ON DIP
4 5 6
123
ON DIP
4 5 6
123
ON DIP
4 5 6
123
ON DIP
4 5 6
123
ON DIP
4 5 6
1 2 3
ON DIP
4 5 6
1 2 3
ON DIP
4 5 6
1 2 3
ON DIP
4 5 6
1 2 3
ON DIP
4 5 6
1 2 3
ON DIP
4 5 6
123
ON DIP
4 5 6
123
ON DIP
4 5 6
123
ON DIP
4 5 6
123
ON DIP
4 5 6
123
ON DIP
4 5 6
1 2 3
ON DIP
4 5 6
1 2 3
ON DIP
4 5 6
1 2 3
ON DIP
4 5 6
1 2 3
ON DIP
4 5 6
1 2 3
ON DIP
4 5 6
123
ON DIP
4 5 6
123
ON DIP
4 5 6
123
ON DIP
4 5 6
123
ON DIP
4 5 6
123
ON DIP
4 5 6
123
ON DIP
4 5 6
123
ON DIP
4 5 6
123
ON DIP
4 5 6
123
ON DIP
4 5 6
123
ON DIP
4 5 6
123
ON DIP
4 5 6
123
ON DIP
4 5 6
123
ON DIP
4 5 6
123
ON DIP
4 5 6
123
ON DIP
4 5 6
123
ON DIP
4 5 6
123
ON DIP
4 5 6
123
ON DIP
4 5 6
123
ON DIP
4 5 6
123
ON DIP
4 5 6
123
ON DIP
4 5 6
1 2 3 4 5 6
ON
NA2
+AP-
C1 NA1 AP+ C2 AP+ AP- P1 P2 BUSBUS
Relay 2
Relay 1
_
12Vdc
12
Front Back
VESTA2 VESTA2
Monitor code Monitor codeMonitor code
Co 1de Co 0 / 32de
Co 10de Co 9de
Co 8de Co 7de
Co 6de Co 5de
Co 4de Co 3de
Co 2de Co 11de
Co 20de Co 19de
Co 18de Co 17de
Co 16de Co 15de
Co 14de Co 13de
Co 12de Co 21de
Co 30de Co 29de
Co 28de Co 27de
Co 26de Co 25de
Co 24de Co 23de
Co 22de Co 31de
Co 1de
Co 10de
Co 8de
Co 6de
Co 4de
Co 2de
Co 20de
Co 18de
Co 16de
Co 14de
Co 12de
Co 30de
Co 28de
Co 26de
Co 24de
Co 22de
( )
** -In door panel systems with call buttons, the first address on the monitor is 'Code 0'.
-In the software (Address Manager GB2), call 'code 0' of button 'P1' on the sound module is also shown as 'code 32'.
( )
**
Co 10de Co 9de
Co 8de Co 7de
Co 6de Co 5de
Co 4de Co 3de
Co 2de Co 11de
Co 20de Co 19de
Co 18de Co 17de
Co 16de Co 15de
Co 14de Co 13de
Co 12de Co 21de
Co 30de Co 29de
Co 28de Co 27de
Co 26de Co 25de
Co 24de Co 23de
Co 22de Co 31de
C 1ode C 0ode
RD-GB2A BUS AMPLIFIER
INSTALLATION
Module No. 1
Module No. 2
Module No. 3

19
Configuring single button module codes:
1 2 3 4 5 6 7 8
ON
9 10
78
56
34
12
1 2 3 4 5 6 7 8
ON
9 10
78
56
34
12
1 2 3 4 5 6 7 8
ON
9 10
78
56
34
12
Not used
Not used
Not used
Not used
Not used
Not used
Not used
Not used
Not used
Not used
Not used
Not used
Not used
Not used
Not used
Continued overleaf
EL632 GB2
P1
P2 P2
Not used
1 2 3 4 5 6
ON
NA2
+AP-
C1 NA1 AP+ C2 AP+ AP- P1 P2 BUSBUS
Relay 2
Relay 1
_
12Vdc
12
EL632 GB2A
EL610D
1 2 3
ON DIP
4 5 6
C 0/32ode
C 5ode
C 4ode
C 3ode
C 2ode
C 1ode
C 10ode
C 9ode
C 8ode
C 7ode
C 6ode
C 15ode
C 14ode
C 13ode
C 12ode
C 11ode
Front Back
VESTA2
Monitor code
P1
Not used
Not used
Not used
Not used
Not used
Not used
Not used
Not used
Not used
Not used
Not used
Not used
Not used
Not used
Not used
Not used
1 2 3
ON DIP
4 5 6
1 2 3
ON DIP
4 5 6
1 2 3
ON DIP
4 5 6
1 2 3
ON DIP
4 5 6
1 2 3
ON DIP
4 5 6
1 2 3
ON DIP
4 5 6
1 2 3
ON DIP
4 5 6
1 2 3
ON DIP
4 5 6
1 2 3
ON DIP
4 5 6
1 2 3
ON DIP
4 5 6
1 2 3
ON DIP
4 5 6
1 2 3
ON DIP
4 5 6
1 2 3
ON DIP
4 5 6
1 2 3
ON DIP
4 5 6
1 2 3
ON DIP
4 5 6
( )
**
C 5ode
C 4ode
C 3ode
C 2ode
C 1ode
C 10ode
C 9ode
C 8ode
C 7ode
C 6ode
C 15ode
C 14ode
C 13ode
C 12ode
C 11ode
C 0ode
RD-GB2A BUS AMPLIFIER
INSTALLATION
( )
** -In door panel systems with call buttons, the first address on the monitor is 'Code 0'.
-In the software (Address Manager GB2), call 'code 0' of button 'P1' on the sound module is also shown as 'code 32'.
Module No. 1
Module No. 2
Module No. 3

20
1 2 3 4 5 6 7 8
ON
9 10
78
56
34
12
1 2 3 4 5 6 7 8
ON
9 10
78
56
34
12
1 2 3 4 5 6 7 8
ON
9 10
78
56
34
12
Not used
Not used
Not used
Not used
Not used
Not used
Not used
Not used
Not used
Not used
Not used
Not used
Not used
Not used
Not used
Continued from previous page.
1 2 3 4 5 6 7 8
ON
9 10
78
56
34
12
Not used
Not used
Not used
Not used
Not used
Not used
Not used
Not used
Not used
EL610D
1 2 3
ON DIP
4 5 6
1 2 3
ON DIP
4 5 6
1 2 3
ON DIP
4 5 6
1 2 3
ON DIP
4 5 6
1 2 3
ON DIP
4 5 6
1 2 3
ON DIP
4 5 6
1 2 3
ON DIP
4 5 6
1 2 3
ON DIP
4 5 6
1 2 3
ON DIP
4 5 6
1 2 3
ON DIP
4 5 6
1 2 3
ON DIP
4 5 6
Co 25de
Co 24de
Co 23de
Co 22de
Co 21de
Co 30de
Co 29de
Co 28de
Co 27de
Co 26de
Co 31de
1 2 3
ON DIP
4 5 6
1 2 3
ON DIP
4 5 6
1 2 3
ON DIP
4 5 6
1 2 3
ON DIP
4 5 6
1 2 3
ON DIP
4 5 6
Co 20de
Co 19de
Co 18de
Co 17de
Co 16de
Not used
Not used
Not used
Not used
Not used
Not used
Not used
Not used
Not used
Not used
Not used
Not used
Not used
Not used
Not used
Not used
Not used
Not used
Not used
Not used
Monitor code
C d 20o e
C d 19o e
C d 18o e
C d 17o e
C d 16o e
C d 25o e
C d 24o e
C d 23o e
C d 22o e
C d 21o e
C d 30o e
C d 29o e
C d 28o e
C d 27o e
C d 26o e
C d 31o e
RD-GB2A BUS AMPLIFIER
INSTALLATION
Module No. 5
Module No. 6
Module No. 7
Module No. 4