Altronix T1RAL3F8 User manual

Rev. T1RAL111518 More than just power.TM
Installing Company: _______________ Service Rep. Name: __________________________________
Address: _____________________________________________ Phone #: __________________
Installation Guide
All registered trademarks are property of their respective owners.
T1RAL3F8
8 Door Kit with Fused Outputs
Fully assembled kit includes:
- Trove1R rack enclosure with Altronix backplane (TAL1R)
- (1) eFlow6NB - Power Supply/Charger
- (1) VR6 - Voltage Regulator
- (1) PDS8 - Fused Dual Output Power Distribution Module
- (1) ACMS8 - Fused Dual Output Access Power Controller
T1RAL33F16
16 Door Kit with Fused Outputs
Fully assembled kit includes:
- Trove1R rack enclosure with Altronix backplane (TAL1R)
- (2) eFlow6NB - Power Supply/Chargers
- (2) ACMS8 - Fused Dual Output Access Power Controllers
All components of these Trove kits are UL Listed sub-assemblies.
Please refer to the included corresponding
Sub-Assembly Installation Guides for further information.
Access & Power Integration

- 2 - Trove1RAL Series Installation Guide
Overview:
Altronix Trove Rack kits are pre-assembled and consist of Trove1AL1R enclosure/backplane with factory
installed Altronix power supply/charger(s) and sub-assemblies.
Configuration Chart:
Altronix
Model
Number
120VAC
60Hz
Input
Current
(A)
Power
Supply
Board
Input
Fuse
Rating
Power
Supply
Board
Battery
Fuse
Rating
Nominal DC
Output Voltage Maximum Supply
Current for Main
and Aux. Outputs on
Power Supply board
and ACMS8 Access
Power Controllers’
outputs
Fail-Safe/Fail-Secure or Dry Form “C” Outputs Current Per ACMS8 Output (A) ACMS8 Board Input Fuse Rating ACMS8 Board Output Fuse Rating PDS8 Board Input Fuse Rating PDS8 Board Output Fuse Rating
[DC] [Aux]
Output
Range
(VDC)
Output
Range
(VDC)
T1RAL3F8 3.5 5A/
250V
10A/
32V
20.19-
26.4
20.19-
26.4 24VDC @ 5.6A 8 2.5 15A/
32V
3A/
32V
10A/
32V
3A/
32V
T1RAL33F16 75A/
250V
10A/
32V
Power Supply 1 (24VDC)
16 2.5 15A/
32V
3A/
32V – –
20.19-
26.4
20.19-
26.4 24VDC @ 5.6A
Power Supply 2 (12VDC)
10.0-
13.2
10.1-
13.2 12VDC @ 5.3A
Specifications:
Agency Listings:
• CE European Conformity.
Mechanical:
• Black enclosure with ample knockouts for
convenient access.
• Includes: tamper switch, cam lock and
mounting hardware.
• Modular 2U standard EIA 19” drawer with
extendable slides up to 48”.
• Dimensions (H x W x D): 3.375” x 19.0” x 26.5”
(85.8mm x 482.6mm x 673.1mm)
Included Accessories:
• One (1) tamper switch
(Altronix Model TS112 or equivalent).
• Cam lock.
Available Accessories (not included):
• RE2: Rack Mount Battery Enclosure accommodates
up to four (4) 12VDC/7AH batteries.
• WM5, WM25, WM100: Magnetic Cable Tie Mounts
(5, 25, 100 counts).

Trove1RAL Series Installation Guide - 3 -
Installation Instructions for Altronix Trove Rack Kits:
Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/ANSI, and with all local
codes and authorities having jurisdiction. These products are for indoor use only and must be installed within
the protected premises.
Note: First assemble and Install Z Bracket Wire Management Accesory
(refer to Z Bracket Installation pg. 4)
1. Remove backplane from enclosure prior to installing into rack cabinet
(do not discard hardware).
2. In order to mount included UL Listed tamper switch (Altronix Model TS112 or
equivalent) turn the enclosure upside down. Punch out the knockout in
designated location, on the back of the unit, from outside of the drawer
(Fig. 1, pg. 3). Insert the tamper switch into the knockout from outside of the
drawer with the button facing outwards and spaded connectors inside the drawer.
Connect tamper switch wiring to the Access Control Panel input or the
appropriate UL Listed reporting device.
To activate alarm signal open the rack drawer.
3. Slide the rack enclosure into an open 2U location in the four post rack cabinet.
4. Utilizing proper fasteners attach front ears to the rack rails.
5. Attach the rear of the adjustable slides to the rear rails of the rack cabinet with the proper fasteners.
6. Secure the rack cover (Fig. 2a, pg. 3) and rack drawer to earth ground (Fig. 2b, pg. 3).
7. Make sure that all internal cofigurations (wiring, voltage selection, switch settings, etc.) are
complete before mounting backplane back into enclosure.
8. Refer to the eFlow Power Supply/Charger Installation Guide for eFlow6NB and corresponding sub-assembly
Installation Guides for the following models: ACMS8, PDS8, VR6 for further instructions.
Fig. 1
Back of the drawer,
viewed from outside.
Tamper Switch
mounting location
Fig. 2
Fig. 2a
Fig. 2b

- 4 - Trove1RAL Series Installation Guide
Assembling and Attaching
Z Bracket Wire Management Accessory (included):
Altronix Trove Rack enclosures include Z Bracket, a convenient and reliable wire management accessory.
Hardware (included):
Ten (10) bolts and eight (8) lock nuts.
1. Carefully unpack Z Bracket. Do not discard hardware
(included) (Fig. 3, pg. 4).
2. Attach arms to each other using bolts and
lock nuts (Fig. 3a, pg. 4).
3. Attach the hinge brackets to the ends of
arms using bolts and nuts positioning
them as shown on (Fig. 3b, pg. 4).
4. Make sure that all nuts are tightened.
5. Attach the hinge bracket on the longer side of Z Bracket to the adjustable slide using bolts and lock nuts
(included) (Fig. 4, 4a, pg. 4).
6. Attach the hinge bracket on the shorter side of Z Bracket to the rear of the rack enclosure using bolts
(included).
Fig. 4
Fig. 4a
Fig. 3b
Two (2)
Fig. 3
Fig. 3a

Trove1RAL Series Installation Guide - 5 -
T1RAL3F8 Configuration:
Fig. 5
AC
L G N
DCAC1 1 min
enable 2 hr. disable
OFF - 24V
ON - 12V
ON
TRIGGER EOL
SUPERVISED
--- BAT + --- DC +
NC C NO
AC FAIL
NC C NO
BAT FAIL + AUX ---
NO GND
RESET
Altronix
eFlow6NB
24VDC
Altronix
VR6/PDS8
OUT1 OUT2 OUT3 OUT4 OUT5 OUT6 OUT7 OUT8
1 2 3 4 5 6 7 8
Common Power Outputs (NEG)
P
N
+ INP1 - + INP2 -
PDS8
Dual Voltage
Power Distribution
Module
PWR2+ PWR2+
COM -
COM -
P
N
Fuse1
Fuse2 Fuse3 Fuse4 Fuse5 Fuse6 Fuse7 Fuse8
IN1 Fuse
IN2 Fuse
PWR1+ PWR1+
OUT1
RISK OF FIRE REPLACE FUSES WITH SAME TYPE AND RATING
OUT2
OUT3
OUT4
OUT5
OUT6
OUT7
OUT8
PWR1+
PWR1
PWR1<-->PWR2
PWR1<-->PWR2
PWR1<-->PWR2
PWR1<-->PWR2
PWR1<-->PWR2
INP Logic
NO <-->NC
FACP
EN <-->DIS FACP
FACP
FACP
EOL JMP
PWR2+
Power 2
Power 1
+INP2--+INP1-- +INP3-- +INP4-- +INP5-- +INP6-- +INP7-- +INP8--
15
3
3
3
3
3
3
3
3
ACMS8 ACMS8CB
1 2 3 4
ON
15
PWR1+
PWR2+
COM--
COM--
5 6 7 8
1 2 3 4 5 6 7 8
ON
ONON
PWR2
OFF
+PWR1-- +PWR2--
NC RST EOL +F +R
C GND GND -F -R
NO C NC COM NO C NC COM
Output 1 Output 2
NO C NC COM NO C NC COM
Output 3 Output 4
NO C NC COM NO C NC COM
Output 5 Output 6
NO C NC COM NO C NC COM
Output 7 Output 8
Altronix ACMS8
To IEC connector
To LED
lense

- 6 - Trove1RAL Series Installation Guide
T1RAL33F16 Configuration:
Fig. 6
AC
L G N
DCAC1 1 min
enable 2 hr. disable
OFF - 24V
ON - 12V
ON
TRIGGER EOL
SUPERVISED
--- BAT + --- DC +
NC C NO
AC FAIL
NC C NO
BAT FAIL + AUX ---
NO GND
RESET
Altronix
eFlow6NB
24VDC
AC
L G N
DCAC1 1 min
enable 2 hr. disable
OFF - 24V
ON - 12V
ON
TRIGGER EOL
SUPERVISED
--- BAT + --- DC +
NC C NO
AC FAIL
NC C NO
BAT FAIL + AUX ---
NO GND
RESET
Altronix
eFlow6NB
12VDC
OUT1
RISK OF FIRE REPLACE FUSES WITH SAME TYPE AND RATING
OUT2
OUT3
OUT4
OUT5
OUT6
OUT7
OUT8
PWR1+
PWR1
PWR1<-->PWR2
PWR1<-->PWR2
PWR1<-->PWR2
PWR1<-->PWR2
PWR1<-->PWR2
INP Logic
NO <-->NC
FACP
EN <-->DIS FACP
FACP
FACP
EOL JMP
PWR2+
Power 2
Power 1
+INP2--+INP1-- +INP3-- +INP4-- +INP5-- +INP6-- +INP7-- +INP8--
15
3
3
3
3
3
3
3
3
ACMS8 ACMS8CB
1 2 3 4
ON
15
PWR1+
PWR2+
COM--
COM--
5 6 7 8
1 2 3 4 5 6 7 8
ON
ONON
PWR2
OFF
+PWR1-- +PWR2--
NC RST EOL +F +R
C GND GND -F -R
NO C NC COM NO C NC COM
Output 1Output 2
NO C NC COM NO C NC COM
Output 3 Output 4
NO C NC COM NO C NC COM
Output 5 Output 6
NO C NC COM NO C NC COM
Output 7 Output 8
OUT1
RISK OF FIRE REPLACE FUSES WITH SAME TYPE AND RATING
OUT2
OUT3
OUT4
OUT5
OUT6
OUT7
OUT8
PWR1+
PWR1
PWR1<-->PWR2
PWR1<-->PWR2
PWR1<-->PWR2
PWR1<-->PWR2
PWR1<-->PWR2
INP Logic
NO <-->NC
FACP
EN <-->DIS FACP
FACP
FACP
EOL JMP
PWR2+
Power 2
Power 1
+INP2--+INP1-- +INP3-- +INP4-- +INP5-- +INP6-- +INP7-- +INP8--
15
3
3
3
3
3
3
3
3
ACMS8 ACMS8CB
1 2 3 4
ON
15
PWR1+
PWR2+
COM--
COM--
5 6 7 8
1 2 3 4 5 6 7 8
ON
ONON
PWR2
OFF
+PWR1-- +PWR2--
NC RST EOL +F +R
C GND GND -F -R
NO C NC COM NO C NC COM
Output 1Output 2
NO C NC COM NO C NC COM
Output 3 Output 4
NO C NC COM NO C NC COM
Output 5 Output 6
NO C NC COM NO C NC COM
Output 7 Output 8
To IEC connector
Altronix ACMS8
Altronix ACMS8
To LED lenses

Trove1RAL Series Installation Guide - 7 -
Notes:

- 8 - Trove1RAL Series Installation Guide
Trove1R Enclosure Dimensions:
3.375” x 19.0” x 26.5” (85.8mm x 482.6mm x 673.1mm). Shown with Z Bracket attached.
0.1”
2.5mm
1.5”
38.1mm
11.175” (283.8mm)
2.4”
61mm
4.57”
116.1mm
3.375”
85.8mm
26.5”
673.1mm
19” (482.6mm)
R 1.27” (32.3mm)
1” (25.4mm)
0.55” (14mm)
3.62”
92mm
Altronix is not responsible for any typographical errors.
––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
140 58th Street, Brooklyn, New York 11220 USA | phone: [phone] | fax: [phone]
website: www.altronix.com | e-mail: [email protected] | Lifetime Warranty
IITrove1RAL Series H31U MEMBER