Bluetooth Wireless Speaker - Speakerphone
qsg Q10230 Copyright © 2012 Aluratek, Inc. All Rights Reserved.
aluratek.com
Quick Start Guide
ABS02F
Product Application
Operation
Note: The pairing mode will last 2 minutes. ABS02F will switch to the standby mode automatically if
no devices can be connected within 2 minutes.
Pairing with the transmitter such as iPhone, smart phone, and tablet:
Please make sure the device supports A2DP profile. The pairing procedure will vary
depending on the actual device. Please refer to the user guide of your device for
detail instruction. The general pairing procedures are as follows:
1. Make sure ABS02F is turned ON.
2. Activate ABS02F pairing mode by press and hold the button for 10 seconds.
(you will hear 3 audio tones and the blue LED will flash rapidly)
3. Activate your device’s Bluetooth function and set your device to search for Bluetooth
devices. Select ABS02F when it is found.
4. For transmitter with Bluetooth version 2.1, you will not need to input a code. If you
are prompted for PIN, please enter “0000”.
5. If prompted by your device to connect, please select “Yes”.
6. After connecting successfully, the blue LED will flash every 5 seconds.
Note: Please make sure the audio output is set to Bluetooth / ABS02F for audio streaming from the device.
For more information, please visit: http://aluratek.com/warranty-return-policy
You can register your product online at: http://aluratek.com/product-registration
Web: www.aluratek.com/support
Local (Tustin, CA): 714-586-8730
Toll free: 1-866-580-1978
Aluratek warrants this product against defect in material or workmanship for
1 Year from the date of purchase.
If you need further assistance, please contact the Aluratek support department for
troubleshooting prior to returning this device.
Tech Support & Warranty Information
Operation
Charging the battery
The battery is not fully charged and it is highly recommended that you charge ABS02F
before you begin using it.
Note: Using ABS02F “out of the box” will not harm the device. You will experience reduced battery life as the
unit will not be fully charged.
Connect the larger USB end of the cable provided to your PC / power adapter.
Connect the smaller USB end to charging port of ABS02F. Please charge the battery
for a minimum of (4) hours. The Red LED will be on while charging. When charging
is complete, the red LED will turn off.
Function Operation LED Indicator
Power On Switch the power button to ON Red LED ON
Radio and TV Interference Statement
WARNING!!! This equipment has been tested and found to comply with the limits of a
Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed
to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by whatever measures may be
required to correct the interference.
Volume control
Charge the built-in
lithium ion battery
with the included
USB cable
On - Off switch
Connect any MP3 Player
with a 3.5mm auxiliary
audio output
(2W x 2) Speakers
Microphone: Pair with
your smartphone to use as
a wireless speakerphone
Forward / Backward
Play / Pause / Pair / Connect
and Disconnect incoming call
Enter Pairing
Mode
Ensure ABS02F is turned ON. Press and
hold button for 10 seconds. You
will hear 3 audio tones
Blue LED flashes
every 5 seconds
Enable
Bluetooth
(after Power
ON / OFF)
Ensure ABS02F is turned ON. Press and
hold button for 7 seconds.
Blue LED flashes
rapidly
