ALZA HC-812LTE User manual

TRAIL CAMERA
HC-812LTE
User Manual • Uživatelský manuál •
Užívateľský manuál • Használati utasítás •
Benutzerhandbuch

2
English
3 –30
Čeština
31 –58
Slovenčina
59 –86
Magyar
87 –114
Deutsch
115 –144

3
Dear customer,
Thank you for purchasing our product. Please read the following instructions carefully
before first use and keep this user manual for future reference. Pay particular attention
to the safety instructions. If you have any questions or comments about the device,
please contact the customer line.
󲐜󲐝󲐞󲐟󲐠www.alza.co.uk/kontakt
✆[phone]
Importer Alza.cz a.s., Jankovcova 1522/53, Holešovice, 170 00 Praha 7, www.alza.cz

4
SPECIFICATIONS
Cellular/Wireless
Frequency
G(FDD LTE, TDD LTE)
3G(WCDMA)
2G(GSM
Photo recording
Photo resolution
20MP / 16MP /12MP
File format
JPG
Time lapse mode
5min/30min/1h
Multi-shot mode
Up to 9 photos per detection
Stamp (photos and video)
Date, time, temperature (°C/°F) and
moon phase
Capture mode
Color by day, black and white by night
Audio
Sound recording
(automatically recorded in video
Mode)
N/A
Memory storage
Support
Internal memory: none
External memory : SD/SDHC card
(up to 64 GB)
Viewing
Built-in screen
TFT 2.4”
Power source
Alkaline or lithium batteries
8 x AA
Lithium battery pack
Rechargeable battery pack(LIT-
801)
External (5.5X2.1mm Jack)
DC12V 1000mA ,(6V~12V)
Detection system
Motion sensor
3X PIR
Detection angle
120°
Detection range
Adjustable from 1 to 80 ft
Trigger speed
0.3 sec
Delay between each detection
Adjustable from Instant to 30 min
Night time illumination system
LEDs
6 LEDs
Flash range
< 90 ft
Exposure
Automatic infrared level adjustment
Optical field of view
120°
Dimensions
135mm X 90mm X 76mm
Recommendations
Operating temperature
(-30 °C to + 50 °C) (-22 °F to +122 °F)
Storage temperature
(-40 °C to + 60 °C) (-40 °F to +140 °F)

5
Latch
High power invsibile LED
Photosensor
LED indicator
Lens
Central PIR
Sensor
Side PIR
Sensor
Color Display
Screen
Setup Buttons
8AA Batteries Depot
IM Card slot
USB Port
Micro SD Card
Slot
Mode
Switch
Stand Knob Port

6
INSTALLING BATTERIES
1.Pull the gap lightly and open battery
compartment.
2 Reference the battery icons located on
the inside of the battery compartment.
Insert the batteries according to the
positive and negative battery icons.
3.Close the battery compartment to
resist water and dust.
NOTE: Installing any of the 8-AA batteries
in the wrong direction may cause the
batteries to leak acid and could possibly
explode, causing camera failure and
damage to the battery compartment.

7
BATTERIES CONT
IF USING 12V DC POWER SOURCE
1. Remove the rubber port cap at the
bottom of the camera . Using a universal
12V DC cord, plug in to the bottom port
option.
2. Run the cord to the side of the camera
where there is a hook provided behind
the hinge of the camera door. This will
support the power cord and take
pressure off of the connection point
3. When not in use, replace the rubber
port cap at the bottom of the camera to
protect the 12V DC universal plug-in port.

8
MEMORY CARD INSTALL
INSTALL MICRO-SD CARD
1. Insert the Micro SD card with the
contacts facing away. The Micro SD card
should slide in freely with little resistance.
Continue pressing the card inward until
you hear a click. This means the Micro SD
card is locked in place and ready for
2. To remove Micro SD card, press the
card inwards to release.

9
OPERATING BUTTONS
MENU: Open the Settings menu using the MENU button
REPLAY: Press this button to start the replay mode
Change to the manual recording mode for video recordings
Change to the manual recording mode for taking photos
SHOT: Manually take a video or photo depending on the set recording mode. Video
recordings are ended by pressing the SHOT button
Ok, : No function(in recording mode)

10
QUICK START
Power on
Slide Power Switch from OFF to Test(for setting) then to ON position, the camera powers
on.(Please don't slide the power switch from OFF to ON directly)
A SIM card is needed. Make sure your SIM card supports Short Messaging Service (SMS),
Multimedia Messaging Service (MMS) and data traffic service. When SIM card recognized
by camera, the camera display will show carrier's icon.
TEST (The first way to set the menu)
In TEST mode, the screen lights up. User can do the below operations by remoter:
•Setting Camera Menu, working mode includes camera, video and system setting
•Take picture or video (Press Shot)
•View picture or video (Press OK)
•Check the MMS/SMTP is ON or OFF
ON
In this mode, the screen power off and remoter is useless. The camera works
automatically. Will capture and send picture out if detected any motions by PIR.