Amazon B07F2C9CFR Operating and safety instructions

created by: Impala Services Ltd.
Page size: A4
B07F2C9CFR, B07F285PQ6, B07FHBYCMC
Two-Handle Hi-Arc Kitchen Faucet
Grifo de Cocina Bimando con Arco Alto
Robinet de Cuisine Surélevé à Deux Poignées

English .............................3
Español............................7
Français .........................11

3
Welcome Guide •English
Contents:
Before getting started, ensure the package contains the following components:
Faucet x1 Sprayer with hose x1
Deck plate gasket (faucet) x1 Sprayer base x1
Rubber washer (faucet) x2 Rubber washer (sprayer base) x1
Locking nut (faucet) x2 Locking nut (sprayer base) x1
Recommended Tools:
• Safety goggles x1 • Adjustable wrenches x1
Part List
Parts Description Qty
AHandle x2
BRed & blue indicator x2
CScrew (H2.5 x M5 x 6 mm) x2
DCap x2
ECartridge (1/2) x2
FRubber washer (Ø45 x Ø21 x 2.5 mm) x2
GLocking nut x2
HAerator gasket x1
IAerator x1
JAerator housing x1
KQuick connector x1
LSprayer hose x1
MSprayer head x1
NSprayer base x1
ORubber washer (Ø45 x Ø21 x 2.5 mm) x1
PLocking nut x1
A
B
C
D
E
G
H
I
J
K
L
M
N
O
P
F
Before First Use
Check for transport damage.
Risk of suffocation! Keep any packaging materials away from children – these materials are a potential
source of danger, e.g. suffocation.
DANGER

4
Installation
Step 1:
Shut Off Water Supply
• Locate water supply inlets and shut off the water supply
valves. These are usually found under the sink or near
the water meter. If you are replacing an existing faucet,
remove the old faucet from the sink and remove any dirt
and/or plumber’s putty from around the faucet holes.
Step 2:
Setup
Deck cover
Lip
Rubber
washer (F)
Locking nut (G)
Deck plate gasket
• Remove locking nuts (G) and rubber washers (G) from
the two water inlet tubes on the faucet.
• Lay the deck plate gasket over the holes in the sink.
• Place the deck cover over the base plate gasket.
Make sure the lip going around the base
plate gasket is pointing upward and that the deck cover is
sitting correctly on the deck plate gasket.
• Slide one rubber washer (G) over each water inlet pipe.
• Screw one locking nut (G) onto each water inlet pipe and
tighten by hand.
Step 3:
Connect Supply Lines
• Reconnect the hot water line to the left water inlet pipe.
• Reconnect the cold water line to the right water inlet
pipe.
• Use wrench to tighten.
If you are replacing the old water supply
lines, make sure you clean the threads of both water inlet
valves and apply plumber’s tape. Use a wrench to tighten
down fittings and follow above steps to connect water lines
to the faucet.
NOTICE
NOTICE

5
Installation
Step 4:
Install Sprayer Base
Locking nut (P)
Rubber washer (O)
Threaded pipe
Sprayer base (N)
• Remove locking nu (P) and rubber washer (O) from
threaded pipe.
• Insert sprayer base (N) into hole.
• Slide the rubber washer (O), onto the threaded pipe.
• Screw the locking nut (P) onto the threaded pipe and
hand-tighten.
Make sure the sprayer base (N) is centered
over the sink hole and then finish tightening locking nut (P)
by hand.
Step 5:
Connect Sprayer Hose
Quick connector (K) Sprayer
hose (L)
• Slide the sprayer hose (L) through the sprayer base (N).
• Connect sprayer hose (L) into quick connector (K).
Step 6:
Check and Run Water
Water inlet
valve
Cold
supply
hose
Hot
supply
hose
Handle (A) Sprayer head (M)
• Check to make sure the faucet is tight.
• Slowly open one water inlet valve and check for leaks; if
no leaks, open the valve all the way.
• Slowly open the other water inlet valve and check for
leaks; if no leaks, open the valve all the way.
If a leak is spotted, close the valve and
remove the water line, along with the Teflon tape on the
threads. Then re-tape the threads and connect the water
line and repeat the procedure.
• Pull the handle (A) in the direction away from you and
make sure there is hot water coming out of the faucet.
• Pull the handle (A) towards you and make sure there is
cold water coming out of the faucet.
• Remove the sprayer head (M) from the sprayer base (N) and
pull the hose out. Make sure there is nothing obstructing
the hose from being pulled out or retracted.
• With the water running, make certain the sprayer sprays
when the lever is pushed in.
NOTICE
NOTICE

6
Cleaning and Maintenance
• Avoid using abrasive chemicals when cleaning, read the cleaner product label prior to use.
IMPORTANT SAFEGUARDS
Read these instructions carefully and retain them for future use. If this product is passed to a third party, then these
instructions must be included.
When using the product, basic safety precautions should always be followed to reduce the risk of injury including the
following:
• To reduce the risk of injury or property damage, read all instructions before installing product.
• Wear safety goggles.
• Product must be installed in accordance with all state & local plumbing & building codes.
• Call a professional if you are uncertain about installing this product.
IMPORTANT, RETAIN FOR FUTURE REFERENCE: READ
CAREFULLY.
Warranty Information
To obtain a copy of the warranty for this product:
Visit amazon.com/AmazonBasics/Warranty
— or —
Contact Customer Service at 1-866-216-1072
Feedback
Love it? Hate it?
Let us know with a customer review.
AmazonBasics is committed to delivering customer-driven products that live up to your high standards. We encourage you
to write a review sharing your experiences with the product.
Please visit: amazon.com/review/review-your-purchases#
For further services:
Visit amazon.com/gp/help/customer/contact-us
— or —
Contact Customer Service at 1-866-216-1072

MADE IN CHINA
amazon.com/AmazonBasics