American Standard DetectLink 6072121 User manual

M985145 SKU# 607X121 EN (8/23)
6072121/607B121
American Standard is devoted to making life,
in the heart of your home, better every day…
…so, thank you for inviting us in! With the very best in kitchen
and bathroom products, we are here to help make your life
happier, healthier and simpler. Our commitment to quality,
innovation and performance has made us part of your everyday
routine for nearly 150 years, and we look forward to being a
part of your life for many years to come.
Learn more at www.AmericanStandard.com
REGISTER YOUR WARRANTY
Try the easy-scan QR code to quickly enter
your information or find your product’s
detailed warranty here:
www.AmericanStandard.com/warranty
Registering allows you to keep your product information
safe, and us the ability to contact you in the event of a
product recall or any news about your purchase.
And if ever you have a question or need help…?
Call us at 1-855-815-0004

OWNERS MANUAL
IoT DetectLnk™Exposed
Toilet Flush Valve
6072121 / 607B121
Image shown may vary from product purchased.
INSIDE THE BOX (BATTERY VERSION)
Battery Power Kit PK01.WRK
POWER KITS SOLD SEPARATELY
60780XX FOR BATTERY VERSIONS
Vacuum Breaker
Tube
Stop Valve
Flush Valve
INSIDE THE BOX (AC VERSION)
Hard-Wired AC
Power Kit Hard-Wired AC &
Multi-AC Power Kit
PK00.HAC / PK00.BBU PK00.MAC / PK00.HAC
PK00.BBU
POWER KITS SOLD SEPARATELY
607BXXX/607B0XX FOR AC VERSIONS
Vacuum Breaker
Tube
Stop Valve
Flush Valve
NOTE TO INSTALLER: Please give this manual to the customer after installation.
To learn more about American Standard Selectronic®Products visit our website at:
www.americanstandard-us.com or e-mail us at: [e-mail]
For Parts, Service, Warranty or other Assistance,
please call (844) CRT-TEAM / [phone]
(In Toronto Area only: 1-905-306-1093)

PRIOR TO INSTALLATION
Note: Prior to installing the DetectLnk™ Flush Valve the following items must be
installed.
1. Urinal/Toilet
2. Drain line
3. Water supply line
IMPORTANT:
• All plumbing and electrical wiring should be installed in accordance with applicable
codes and regulations.
• The use of water hammer arrestors is strongly recommended for commercial applications.
All piping behind the walls should be properly secured and fastened.
• Water supply lines must be sized to provide an adequate volume of water for each fixture.
• Flush all water lines prior to operation Dirt and debris can cause flush valve to run
continuously.
• With the exception of Stop Valve Inlet, DO NOT use pipe sealant or plumbing grease
on any valve component or coupling!
• Protect the chrome or special finish on the Flushometer. DO NOT USE toothed tools on
finished surfaces to install or service these valves. Also see “Care and Cleaning”
section of this manual.
• This product contains mechanical and/or electrical components that are subject to normal
wear. These components should be checked on a regular basis and replaced as needed to
maintain the valve’s performance.
Consult xture manufacturer for minimum pressure requirements. Most High
Efciency water closets require a minimum owing pressure of 25 psi (172 kPa).
Many building codes and the ASME A112.19.2 xture standard list Maximum
static water pressure as 80 PSI (552 kPa).
10'
RECOMMENDED TOOLS
Teflon Tape
Installation steps will indicate which tools should be used with asscociated letter
A
Flat Blade
Screwdriver
B
Adjustable
Wrench
C
Hacksaw
D
Tape Measure
E
Tubing Cutter
F
File
G
2.5 & 1.5 mm
Hex Wrench
H
Solder & Torch
I

Note: Install Optional Sweat Adapter (Supplied) for
copper pipe supply line.
1. Measure the distance (A) from the finished wall to the
center of the inlet spud on the fixture.
2. Cut the supply pipe 1-1/4” (A-B=C) shorter than the
measurement taken in Step 1. File any rough edges
off the end of the supply pipe.
3. Clean the end of the supply pipe. Push the threaded
Adapter until it is seated against the internal stop.
Sweat the Adapter to the pipe.
CENTER LINE OF
FIXTURE SPUD
FINISHED WALL
FILE EDGES
SOLDER
ADAPTER
ADAPTER
32mm
(1-1/4")
A
(A-B)= B
C
CLEAN
1INSTALL SWEAT ADAPTER
F
2INSTALL COVER TUBE, WALL ESCUTCHEON AND STOP VALVE
Turn off hot and cold water
supplies before beginning.
Fig. 4a
Fig. 4b
Fig. 4c
1
1
4
2
3
TEFLON TAPE
FINISHED WALL
X
X
2
FLUSH VAVLE INSTALLATION
1. Measure from finished wall to first thread of Adapter
or threaded supply pipe (dimension “X”). Cut
COVER TUBE (1) to length (X). Apply Teflon Tape to
the threaded end of the Adapter or supply pipe.
2. Push WALL ESCUTCHEON (2) onto the COVER
TUBE (1). Slide both onto the SUPPLY PIPE (3).
3. Push the COVER TUBE (1) in to expose the threads
of the supply pipe. With a wrench thread the STOP
VALVE (4) onto the SUPPLY PIPE (3). Align and
tighten.
4. Pull COVER TUBE (1) against STOP VALVE (4) and
push WALL ESCUTCHEON (2) against finished wall.
G I D E
A C D F

3FLUSH OUT SUPPLY LINES
1
CLOCKWISE CLOSES
STOP VALVE
COUNTER-CLOCKWISE
OPENS STOP VALVE
REMOVE COVER
2
2
B
1. Remove STOP VALVE COVER (1) from STOP
VALVE (2).
2. Open STOP VALVE (2) with a flat blade screwdriver.
3. Turn on water supply to flush line of any debris or
sediment.
4. Close STOP VALVE (2) and replace STOP VALVE
COVER (1).
2
4
1
3
4a INSTALL VACUUM BREAKER TUBE: APPLICABLE FOR STANDARD CERAMICS
Note: Step 4a is only applicable if using standard
ceramics. If using IoT Ceramics, skip to step 4b.
1. Insert VACUUM BREAKER TUBE (1) through
HEX NUT (4), FLUSH VALVE BOTTOM COVER
(2), and SPUD COVER (3).
2. Thread SPUD COVER (3) on to the toilet base.
Note: Ensure that the O-ring is properly seated in the
base of HEX NUT (4).
C

1
2
3
4b
1. Slide SPUD COVER (1) over HEX NUT (2).
2. Secure SPUD COVER (1) by tightening SET SCREW (3).
H
INSTALL VACUUM BREAKER TUBE: APPLICABLE WITH ASA IOT CERAMICS
2
6
5
1
3
4
C D
4
7
Note: Step 4b is only applicable if using ASA IoT Ceramics.
Otherwise, refer to step 4a.
1. Separate HEX NUT (4) from SPUD COVER (7).
2. Thread WIRE (5) through FLUSH VALVE BOTTOM COVER
(2) and SPUD COVER (3).
3. Insert VACUUM BREAKER TUBE (1) through
the FLUSH VALVE BOTTOM COVER (2), SPUD COVER (3),
HEX NUT (6), AND HEX NUT (4).
4. Thread HEX NUT (4) on to the Toilet Base.
Note: Ensure that the O-ring is properly seated in the base of
HEX NUT (4).
Note: Vacuum breaker tube can be shortened by up to 1-1/2"
if desired.
Note: Spud Cover (3) and Wire Cover is only available in the
ASA IoT Ceramics Package.

4b CONTINUED
2
1
1. Thread WIRE (1) through the back of FLUSH
VALVE BODY (2).
Note: There is a small hole on the top back of the
brass body for the wire head to fit through.
WIRE HOLE
BOTTOM VIEW

2
1
3
5CONNECT VALVE BODY TO STOP VALVE
1. Push VALVE BODY (1) in to STOP VALVE (2) allowing the O-ring to seal the connection.
2. Thread HEX NUT (3) on to STOP VALVE (2) to secure the connection.
Note: Do not use pipe sealant or plumbing grease.
C
6CONNECT VALVE BODY TO VACUUM BREAKER TUBE
2
1
C
1. Thread HEX NUT (1) on to the bottom of
VALVE BODY (2).
Note: Ensure that the bladder on the vacuum
breaker tube makes a good connection with
the bottom of the flush valve body.
Note: If using a wired version, ensure the
wires do not get pinched while securing the
flush valve body.

2
1
3
4
Note: This step is only applicable if using ASA
IoT Ceramics
1. Insert WIRE COVER (1) through FLUSH VALVE
BOTTOM COVER (3) and SPUD COVER (4).
2. Cover the WIRE (2) with the WIRE COVER (1).
(Applicable with AC Version) Cover the AC wire
with the WIRE COVER (1) similar to WIRE (2).
Note: The Wire Cover will be loose until the
next step to secure it. Ensure that the wire
does not slip out between steps.
Note: Avoid pinching or excessively bending
the wires.
Note: If the vacuum breaker tube was cut to a
shorter length, the wire cover will also need to
be cut. Wire cover length should be from the
top of the installed spud cover to the bottom
of the valve body fixation nut plus 1/8”.
Note: WIRE COVER (1) is only included in ASA
IoT Ceramics Package.
7INSTALL WIRE COVER: APPLICABLE WITH ASA IOT CERAMICS
8SECURE FLUSH VALVE BOTTOM COVER
2
1
H
1. Secure FLUSH VALVE BOTTOM COVER (2)
with the two SET SCREWS (1) on each side.

9a MAKE WIRED CONNECTIONS: BATTERY VERSION
Note: This step is only applicable for the battery
version.
Important: Align the polarity markings (7) on the
wire ends when making the connections.
1. Connect the SOLENOID WIRE (1) to the RED
AND BLACK WIRE (2) in the flush valve head.
2. Connect BLACK AND PURPLE WIRE (5) to the
BATTERY PACK (6) within the top of the flush
valve head.
3. Place the BATTERY PACK (6) within the top of
the flush valve head.
Note: Do not tighten flush valve head at this point.
1
2
6
5
7
9b MAKE HOLE FOR AC WIRE
Note: This step is only applicable for the AC version.
1. Secure FLUSH VALVE HEAD (1) on to the flush
valve body.
2. Using the WIRE CHANNEL (2) as a template,
mark the drill location on the wall.
3. Make an opening in the wall at the marked
location.
IMPORTANT: The hole diameter should be no
smaller than the wire channel and no larger than
the wire channel escutcheon cover.
2
1