Amba Elory E2830 Technical manual

Instructions for Use & Installation
ELORY COLLECTION
CONSULT THIS INSTRUCTION MANUAL IN ITS ENTIRETY PRIOR TO
THE HANDLING & INSTALLATION OF ANY TOWEL WARMER
FOLLOW THE GENERAL GUIDELINES & INCLUDED WIRING DIAGRAM.
790 Pickens Industrial Dr,
Marietta, GA 30339 USA
Phone : [phone]
Fax : [phone]
www.ambaproducts.com
3165407
IP 54
SKU Width HEIGHT Power Amps BTU
E2830 28 3/8” 30 3 /8” 270 watts 2.3 921
E2130 20 1/2” 30 1/2” 180 watts 1.6 614
110v
COMPONENTS
1
1
2
4
5 3
4
2
3
4
5
1 – Plastic Anchor
2 – Washer
3 – Threaded wall support
4 – Fixing Screw
5 — Threaded Fastener
1 – Locking Nut
2 – Cover Plate
3 – Connector
4 – Cover Plate Screws
5 — Threaded Fastener

2
www.ambaproducts.com
IMPORTANT INSTRUCTIONS
WARNINGS & PRECAUTIONS
BEFORE INSTALLING THE TOWEL WARMER CAREFULLY READ ALL INSTRUCTIONS
Ensure that VOLTAGE (V) & FREQUENCY (HZ) indicated in the serial number plate correspond to
the voltage & frequency available in the place of installation
At receipt of goods, ensure that packaging is intact:
ANY DAMAGES THAT OCCUR DURING TRANSPORT
ARE NOT COVERED BY WARRANTY
• This heater is hot when in use — to avoid burns do not let bare skin touch hot surfaces
• For indoor use only
• Wiring procedures & connections shall be in accordance with the national & local codes having jurisdiction
• Piling multiple towels on top of each other increases the risk of discoloring due to heat
• Discoloration of some towels may occur — this could be the result of fabric makeup, detergent residue,
or if too many towels are placed on the towel warmer. For these reasons amba products cannot be held
liable for any damage to towels. Consider the option of using a digital heat controller for delicates,
acrylics, or nylon — for further protection do not place items directly on unit
• When using electrical appliances, basic precautions should always be followed to reduce the risk of fire,
electric shock, & injury to persons, including the following:
• Caution: high temperature, risk of fire — keep electrical cords, drapery, furnishings, & other combustibles away
from front of heater
• Bad smells may be caused by residues inside the heater, or by the inner plastic parts as unit operates with no
liquids inside (dry system)
• Do not use heater in case of damaged wire or plug, in case of malfunction, drop, or other kind of circumstance
that may require adjustments or repair: contact Amba Products
• We recommend the p.V.C. Protective tape is left in place until the heater is fully installed: please remove tape
from bracket location first — after the installation, remove the P.V.C. Protective tape to avoid glue residue
• Be careful while handling the heater to avoid scratching, marking, grazing or denting the surface: these damages
are not covered by the warranty
• Be careful during installation & use in the presence of children & disabled people
• To switch off the heater, press the on/off button
• Wiring the connection to the power source incorrectly will cause sparks & burning/breaking of the heater —
consult installation instructions & wiring diagram carefully
• Ensure that the room trip switch is off before any maintenance operation
• Do not insert foreign bodies inside the heater in order to avoid electrical shocks, fire and damages to the heater
• Do not use the heater close to combustibles, paints, or any other flammable liquid
• Keep the heater away from water in order to avoid electrical shocks or damage to the unit
• Always install per local electrical code
Amba Products declines any responsibility if the instructions mentioned above are not kept
• Utilize the heater only for warming rooms, or warming & drying towels
• Utilize the heater as described in this manual only. Any other use not recommended by Amba Products
may cause fire, electric shock, or injuries to individuals
• Use only on 15 ampere branch circuit —a dedicated circuit is not required.
• The unit has to be connected to a power-supply circuit equipped with an omni-polar disconnection
electrical system, with a distance among contacts of 1/8”

3
www.ambaproducts.com
MAINTENANCE
UPKEEP & CARE
TECHNICAL SPECIFICATIONS
• Before any maintenance operation ensure that the power source is disconnected and that the switch is
in the off position
• Before any maintenance wait for the unit to cool down completely
• Clean the outside surface with a soft cloth and liquid detergent or stainless steel cleaner
• Do not use abrasive cleaning or scouring products
• To maintain the delicate external finishes use the following methods with each finish:
High-quality and high technology, given by a product certified and ratified according to European and American norms for
electrical devices, made of components that meet the standard requirement of current safety regulations: The product’s Heat
Controller is certified ETL Canada and CE with protection degree IP54 that ensures consumer safety.
Surface temperatures of appliances during normal operations are maintained below the temperature of 60–65°c / 140–149°f
without towels, and 90°c / 194°f with towels, as required by following standards:
• For residue buildup do not use extreme pressure on the surface to avoid scratches & damages to the heater
• It is also possible to use a solvent — use caution & make sure to read the technical forms and norms for it’s use
• In case of uncertainty, do not hesitate to contact Amba Products
Amba Products declines any responsibility if these instructions are not followed
• Brushed finishes: rub the soft cloth following the grain of the finish
• Polished finishes: do not rub cloth in a circular motion – do not use excessive force
115v–10A 60Hz UL 2021 SAFETY FIXED AND LOCATION-DEDICATED ELECTRIC ROOM HEATERS
220v--5A 50Hz CE EUROPEAN NORM
CSA C22.2 No. 46 ELECTRICAL AIR-HEATERS, ENVIRONMENTAL PRODUCTS GENERAL INSTRUCTION No. 1
Normal Temperature of Appliance
Temperature of Appliance with Towel
MODEL
ELORY 60–65°C
85–90°C
140–149°F
185–194°F

4
www.ambaproducts.com
INSTALLATION
INSTRUCTIONS
CAUTION:
DO NOT TAKE OFF THE PROTECTIVE P.V.C. TAPE BEFORE INSTALLING TOWEL WARMER TO
AVOID SCRATCHING, MARKING OR GRAZING THE SURFACE.
• Consult electrician to ensure proper wiring.
Brick Wall
Plastic
Anchor
Brick wall:
• Drill the holes in the wall ø6 mm ( 1/4 inches)
and put the plastic anchor (1) into the wall;
Drywall:
• Leave out the plastic anchor (1) and proceed
with step 2
STEP 1
STEP 3
STEP 2
Drywall
Fixing
Screw
Drywall:
• Fasteners should be fixed to studs or structural
members behind the drywall
• If not possible on both sides, toggle bolts can
be used on one side.
• Fasten Threaded Wall support (3) with plastic
anchor (1) with the Fixing Screw (4): repeat
this procedure also for the other points marked
on the wall
• Install the towel warmer in the four connections as
shown in drawing. Technical Drawings can be found
on our website www.Ambaproducts.com
Plastic Anchor
Washer
Threaded
Fastener
Threaded
Wall Support
STEP 4
REMOVE THE PROTECTIVE P.V.C. TAPE BEFORE
SWITCHING THE TOWEL WARMER ON
DIRECT WIRE CONNECTION:

5
www.ambaproducts.com
Built-in DIGITAL HEAT CONTROLLER
OPERATIONAL INSTRUCTIONS
Level Settings:
1 — Minimum Heat
9 — Maximum Heat
STEP 1
INCREASE POWER LEVEL
DECREASE POWER LEVEL
On-OFF TOGGLE
POWER LEVEL DISPLAY
TOUCH CONTROLS WORK BY A LIGHT TOUCH OF YOUR FINGER TIP
After switching on unit wait a few seconds for the self Calibration (lights up in circular movement);
Choose from 9 different heat levels.
Controller can handle up to a maximum power load of 1200watts.
Can be used in conjuction with a hardwired programmable timer (consult electrician)