Ambient Weather EZ-29-24 User manual

Version 2.0 ©Copyright 2019, Ambient LLC. All Rights Reserved. Page 1
Ambient Weather EZ-29-24 Chimney Mounting Pole Kit
User Manual
Table of Contents
1. Introduction.....................................................................................................................................1
2. Warnings and Cautions ...................................................................................................................2
3. Parts List .........................................................................................................................................2
4. Tools Required................................................................................................................................3
5. Installation.......................................................................................................................................3
6. EZ-125-35M 35” Mast Extension (Optional) .................................................................................9
7. Mast Extension Installation...........................................................................................................10
8. Liability Disclaimer ......................................................................................................................10
9. Warranty Information....................................................................................................................10
1. Introduction
Thank you for your purchase of the Ambient Weather EZ-29-24 Chimney Mounting Pole Kit. The
following user guide provides step by step instructions for installation, operation and troubleshooting.
The EZ-29-24 chimney mounting pole kit provides a stable weather station mounting solution for
chimneys. Provides straps for mounting around the chimney.
Ambient Weather pole mounting kit constructed of rust proof 10-steel tubing, galvanized using the
Flo-Coat (zinc-chromate ploymer) for excellent corrosion proof protection.
Includes one 35" 1.25"-diameter smooth mast. Add a mast extension (see below) to extend the pole an
additional 35" per extension.

Version 2.0 ©Copyright 2019, Ambient LLC. All Rights Reserved. Page 2
Figure 1
2. Warnings and Cautions
Warning: Any metal object may attract a lightning strike, including your weather station
mounting pole. Never install the weather station in a storm.
Warning: If you are mounting the weather station to a house or structure, consult a licensed
electrician for proper grounding. A direct lightning strike to a metal pole can damage or destroy your
home.
Warning: Installing your weather station in a high location may result in injury or death.
Perform as much of the initial check out and operation on the ground and inside a building or home.
Only install the weather station on a clear, dry, day.
3. Parts List
QTY
Item
Image
4
Screws
4
Side Clips
4
12” Mounting Assemblies (2 shown
attached together in the image)

Version 2.0 ©Copyright 2019, Ambient LLC. All Rights Reserved. Page 3
QTY
Item
Image
4
Strap Bolts
2
1” Metal Straps
8
7/16” Nuts, 1 for each strap bolt and 1
for each screw
8
Lock washers, 1 for each strap bolt
and 1 for each screw
4. Tools Required
•7/16” deep socket or wrench
•Tin Sheers
•Pliers
•Level or Plumb
5. Installation
1. Pre-assemble the strap bolts, lock washers, nuts, and screws. There are two complete
assemblies per strap.
2. Tighten the strap bolt, lock washer and nut.
3. Finger tighten the screws, lock washer and nut assembly.

Version 2.0 ©Copyright 2019, Ambient LLC. All Rights Reserved. Page 4
Figure 2
4. While on the ground (NOT ON THE ROOF), pre-assemble the metal strapping.
5. Slide one slide clip over each end of the metal strapping with the flanges pointing away from
the chimney.
Figure 3

Version 2.0 ©Copyright 2019, Ambient LLC. All Rights Reserved. Page 5
6. Thread the metal strap through each end of the strap bolts with the strap bolt eyelets pointing
away from the chimney.
Figure 4
7. Bend the metal strap through the strap bolt eyelit.
Figure 5
8. Slide the slide clip over the top of the excess metal strap.

Version 2.0 ©Copyright 2019, Ambient LLC. All Rights Reserved. Page 6
9. Repeat these instructions for the second strap mount assembly.
Figure 6
10. Slide both strap assemblies over the top of the chimney.
Figure 7
11. Pull the strapping taught with pliers by the ends of the metal strapping.
12. Cut excess strap with tin sheers. Leaving at least 3” margin between the slide clips and the
end of the strap.

Version 2.0 ©Copyright 2019, Ambient LLC. All Rights Reserved. Page 7
Figure 8
13. With the metal strapping taught, crimp the side clip flanges by bending onto the metal strap
with pliers. The final tightening procedure is performed in the next step.
Figure 9
14. With a 7/16” deep socket wrench, tighten the metal strap until the unit is secure.
15. Repeat this procedure for the second mounting strap assembly. It is recommended the
mounting straps are at least 12” apart.

Version 2.0 ©Copyright 2019, Ambient LLC. All Rights Reserved. Page 8
Figure 10
16. Insert the metal pole into each of the 12” Mounting Assemblies. Tighten U-nuts to secure the
pole.
17. Use a level or plumb to make sure the pole is level and adjust accordingly.
18. Perform final tightening on all bolts.
19. Cut-off any excess strapping with tin sheers.

Version 2.0 ©Copyright 2019, Ambient LLC. All Rights Reserved. Page 9
Figure 11
6. EZ-125-35M 35” Mast Extension (Optional)
Galvanized 1-1/4 inch (3.25 cm) O.D., 35 inch (89 cm) long steel post with one end crimped for
insertion into another post of the same O.D.
Made of 18 gauge 1008-10 steel tubing, galvanized using the Flo-Coat (zinc-chromate-polymer)
process for excellent corrosion protection.
When used with the EZ-48-3AB-125-35 Mast assembly, this extension will raise the anemometer to a
height of 84 inches, with an effective adjustment range of 72 to 89 inches (187.2 to 231.4 cm).

Version 2.0 ©Copyright 2019, Ambient LLC. All Rights Reserved. Page 10
Figure 12
7. Mast Extension Installation
Insert the swaged end of the mast extension into the mounting tripod mast and tighten so the extension
does not rotate.
Repeat this step for additional mast extensions (maximum two is recommended).
Figure 13
8. Liability Disclaimer
The specifications of this product may change without prior notice.
This product is not a toy. Keep out of the reach of children.
No part of this manual may be reproduced without written authorization of the manufacturer.
Ambient, LLC WILL NOT ASSUME LIABILITY FOR INCIDENTAL, CONSEQUENTIAL,
PUNITIVE, OR OTHER SIMILAR DAMAGES ASSOCIATED WITH THE OPERATION OR
MALFUNCTION OF THIS PRODUCT.
9. Warranty Information
Ambient, LLC provides a 1-year limited warranty on this product against manufacturing defects in
materials and workmanship.
This limited warranty begins on the original date of purchase, is valid only on products purchased and
only to the original purchaser of this product. To receive warranty service, the purchaser must contact
Ambient, LLC for problem determination and service procedures.