Ambifuego KALIDO 73 User guide

October 2005
ACF526 Issue Technigas
KALIDO 73
Convector Gas Fire
MODEL NUMBERS: ACF526NG & ACF526P
INSTALLATION, USER AND SERVICING INSTRUCTIONS
THESE INSTRUCTIONS MUST REMAIN WITH THE USER
THIS APPLIANCE MEETS THE REQUIREMENTS OF THE EUROPEAN GAS DIRECTIVE
BEFORE INSTALLATION, CHECK THAT THE LOCAL DISTRIBUTION CONDITIONS, NATURE OF GAS & PRESSURE AND
ADJUSTMENT OF THE APPLIANCE ARE COMPATIBLE.
0120
Ambifuego
Avda Cañada del Cura, 29, Pol. Ind. de Levante
03187 Los Montesinos - Alicante.
Tel. [phone] Fax. [phone]
Correo electrónico: [e-mail] web: www.ambifuego.net

2
Installation & Service Record
Please ensure that installer completes the installation record below
INSTALLATION RECORD
Appliance Supplied by: …………………………....
Installation Date: ……………Serial No.: ….……...
Installed By: …………..…...Reg. No.: …..……
Signed by Installer: ……………………………..…
RECORD OF 1st SERVICE
Serviced by: ………… Reg. No.:…………....
Service Date: …………… Signed: ….…….…...
Comments: ……………………………………………
……………………………………………………………
……………………………………………………
RECORD OF 2nd SERVICE
Serviced by: ………… Reg. No.:…………....
Service Date: …………… Signed: ….…….…...
Comments: ……………………………………………
………………………………………………………………
……………………………………………………..
RECORD OF 3rd SERVICE
Serviced by: ………… Reg. No.:…………....
Service Date: …………… Signed: ….…….…...
Comments: ……………………………………………
……………………………………………………………
………………………………………………….
RECORD OF 4th SERVICE
Serviced by: ………… Reg. No.:…………....
Service Date: …………… Signed: ….…….…...
Comments: ……………………………………………
………………………………………………………………
……………………………………………………..
RECORD OF 5th SERVICE
Serviced by: ………… Reg. No.:…………....
Service Date: …………… Signed: ….…….…...
Comments: ……………………………………………
……………………………………………………………
……………………………………………………
RECORD OF 6th SERVICE
Serviced by: ………… Reg. No.:…………....
Service Date: …………… Signed: ….…….…...
Comments: ……………………………………………
………………………………………………………………
……………………………………………………
RECORD OF 7th SERVICE
Serviced by: ………… Reg. No.:…………....
Service Date: …………… Signed: ….…….…...
Comments: ……………………………………………
……………………………………………………………
……………………………………………………
RECORD OF 8th SERVICE
Serviced by: ………… Reg. No.:…………....
Service Date: …………… Signed: ….…….…...
Comments: ……………………………………………
………………………………………………………………
……………………………………………………..
RECORD OF 9th SERVICE
Serviced by: ………… Reg. No.:…………....
Service Date: …………… Signed: ….…….…...
Comments: ……………………………………………
……………………………………………………………
…………………………………………………..
RECORD OF 10th SERVICE
Serviced by: ………… Reg. No.:…………....
Service Date: …………… Signed: ….…….…...
Comments: ……………………………………………
………………………………………………………………
………………………………………………..

3
Important Notes –Please read before undertaking the installation
1. This is not a “Do it yourself” product and it must be installed by a competent
person.
2. The fire has a ceramic Fire-bed arrangement; this contains Refractory Ceramic Fibres,
which are man-made vitreous silicate fibres. Excessive exposure to these materials can
cause irritation to eyes, skin and respiratory organs. Hence we recommend that when
handling these materials the release of dust should be kept to a minimum. During
installation and servicing we recommend that a HEPA filtered vacuum be used to remove
any dust and soot in and around the fire. If any of the ceramic fire-bed components need
to be replaced we recommend that the removed parts be sealed in a heavy-duty
polythene bag, and be labelled as RCF waste. RCF not “Hazardous waste” and can be
disposed of at a licensed tipping site for the disposal of industrial waste.
The appliance incorporates a permanent pilot. This is located on the front of the burner,
and must not be adjusted by the installer. This system must not be put out of operation,
and if any parts require changing, only original manufacturer parts shall be used.
This appliance is designed to be used either Natural or LPG gas however, each
individual appliance is only capable of running off the type of gas specified at the time of
purchase. It is important to note that once a type of gas has been specified the fire
cannot run off any other type. The type of gas that your fire is capable of burning is stated
on the data information panel.
This appliance has been designed, tested and approved to meet standards in place for
product use, performance and safety. Installation of your appliance must comply with
current building regulations. It is therefore recommend that a registered gas installer be
employed for this task. The engineer will provide you with information about the safety
limits of the installation and should fix a notice plate in a place where it can be readily
seen.
This appliance is designed as a decorative heating device and consequently all body
parts become very hot in use. Except for the control knob and control access door, which
are designed to stay cool, all other parts are working surfaces and should not be
touched.
The front of this appliance does not give full protection for young children, the
elderly or infirm, extra protection should be considered for these conditions conforming
to BS 6539 or BS 6778. The appliance is not fitted with a functional integral guard. In
normal use, consideration should be given to the use of an additional guard, conforming
to the standard above, such that access to the open flame is minimised
3. The chimney must be swept before the appliance is fitted.
4. The Installation Instructions must be adhered to without exception.
Before fitting this appliance, ensure that the following components are enclosed
a) Gas Fired Convector complete with burner and controls.
b) Installation, Servicing & Users Instructions
c) 1 Packet of ceramic fibre flakes
c) Decorative frame and louvered bottom cover

4
e) Five Piece Log Set.
APPLIANCE DATA
ACF526NG
ACF7526P
GAS TYPE
NATURAL GAS
PROPANE
SUPPLY PRESSURE
20mb
37mb
HEAT INPUT
6.8kW Net
6.6kW Net
GAS RATE
0.72m/h
0.2m/h 512g/hr
INJECTOR SIZE
Ø2.1 mm
Ø1.35mm
GAS CONNECTION
8mm COMPRESSION
ELECTRICAL
230V / 50Hz / 3A
Burner Pressure
17,5mbr 27mbr
NOX Concentration
Class 5
GENERAL INSTALLATION REQUIREMENTS
Fitting the Appliance
1 This installation must be carried out in accordance with all local laws and regulations.
2 The 526 Convector can be fitted into fireplace openings which are large enough or can
be altered to accept this appliance. The dimensions are shown in Figure 1. If the
fireplace has to be altered a lintel may be required to
support the masonry over the opening.
The fireplace opening should be formed
from or lined with non-combustible
material.
3 The installation must meet the requirements of the
current CE regulations.
4 The Hearth
The hearth supporting the appliance within the fireplace
must be made of a non combustible material at least
12mm in thickness.
Because of the heat radiated from this appliance the hearth should extend 250mm in
front of the appliance. Alternatively the appliance may be installed 250mm above finished
floor level without requiring the extended hearth.
5 The Chimney Flue
The following types of chimney or flues are acceptable:
a) A conventional open flue connected with a short length of 100mm diameter flue
pipe and a register plate or lined with a flexible flue liner of at least 100mm
diameter T250 rating.
b) A 100mm diameter (or larger) gas flue
The flue must have a minimum effective height of 3 metres. 90º bends are not allowed.
FIGURE 1

5
No restrictor plate or flue damper is permitted. Where a variable damper is fitted, this
must be removed.
c) A dedicated power flue kit is available for the appliance. The appropriate fitting
instructions are supplied with the kit.
7 Ventilation.
Purpose made ventilation must be installed in accordance with local regulations.
8 The appliance is designed for use with both natural gas and propane. The two gases
require different burners that are not interchangeable between the different gas types. .
9 The appliance must not be installed in a room containing a bath or shower or in a private
garage.
10 Shelf
If a shelf made of combustible material is to be fixed to the wall above the appliance a
space of at least 150mm must be left between the top of the fascia and the underside of
the shelf.
Fitting the Firebox
1 Check that the fireplace is of the correct size or has been modified to accept the selected
firebox. (See Figure 1)
2 It is recommended that, before proceeding further, a simple smoke test be performed to
check the condition of the chimney. Light a smoke match or a twist of rolled paper, hold
it under the open flue and observe the behaviour of the smoke. If it is being drawn into
the chimney proceed with the installation. If not, pre-heat the chimney over the period of
a few minutes and recheck. If there is any doubt about the soundness of the chimney a
smoke pellet should be used after preheating the flue and if smoke still fails to clear,
further investigation of the chimney is required and the appliance MUST NOT be fitted
until any fault has been rectified.
3 Clear the recess of any loose material and ensure that the base on which the appliance
will stand is level.
4 Make good the plasterwork or wall decoration up to the edges of the fire opening.
5 Disassemble the appliance in order to separate the flue connector from the convector
box so that it can be connected to the chimney.

6
a Remove the glass window by undoing the two nuts + two screws and lifting clear.
Store it in a safe place.
b Remove the screw at the bottom of the fascia and pull the burner forward.
Remove the four screws holding the control fascia in position. Remove the screw
holding the circulation fan switch plate to the gas control valve. Loosen the
thermocouple nut and remove the connection wires from the flue temperature
switch. Lift the burner assembly clear of the appliance.
c Undo the four screws holding the firebox in the convector box and lift the firebox
out of the convector box. See figure 2. As the firebox is lifted away disconnect the
circulation fan lead from the wiring box by separating the ‘Molex’ connectors.
d Unscrew the ten self tapping screws securing the flue break assembly to the
convector box and remove.
e From inside the convector box loosen the four screws holding flue connector, slide
it sideways and remove from the outside of the convector box.
6 Install the register plate and the connecting length of flue pipe or line the chimney with
100mm flexible flue liner. Connect and seal the lower end of the flue pipe or liner to the
flue connector. Temporarily lodge the flue connector in position until the convector box is
placed in position. Alternatively a gas flue can be used in which case the appropriate
appliance connector will have to be selected.
7 The gas supply should be routed from the meter or cylinder to a point at the rear of the
fireplace. This point should be on the centre line of the appliance and 35mm above the
base on which the convector box will sit. From this point route the supply in 8mm
diameter tubing forward to the front of the fire opening. Exposed pipe within the fire
opening should be wrapped, painted with bituminous paint or factory sheathed.
8 ‘Knock out’ the gas entry hole in the rear of the convector box with a sharp hammer blow.
Place a diaphragm grommet (supplied) in the hole and cut a slit for the gas supply pipe.
Slide the convector box into position. Reach up through the flue aperture and draw the
flue connector down into position. Pull the four screws previously loosened through the
keyhole slots, slide sideways and tighten the four screws. Re-assemble the flue break
assembly into the convector box with the ten self tapping screws previously removed.
Make sure the convector box is pushed fully home and then fix the flanges to the wall
with wall plugs and screws. Make sure the flue temperature switch sensor is still in
position in its bracket.
9 Place the heat exchanger in position in front of the flue assembly within the convector
box making sure that the flue spigot on the back of the firebox is inserted into the
rectangular hole in the flue break. Re-connect the power supply to the fan using the
FIG. 3

7
molex connector. Fix into place with the four screws previously removed.
10 Temporarily place the burner and mark the gas pipe for cutting. Trim the gas supply pipe
to the mark. The end of the supply tube should finish 10 mm above the base. Prior to
connecting the burner to the gas supply it is advisable to blow out the pipe to clear any
dirt that may be present and which could cause a blockage in the control valve or pilot.
11 Replace the connection from the flue temperature switch and tighten the thermocouple
nut (Caution; do not over tighten). Replace the burner/control assembly in position and
secure. Fix the switch box to the gas control valve with the M4 screw previously
removed. Replace the fascia panel and secure with four black headed self tapping
screws. Using the nut and olive provided, connect the 8mm supply pipe to the pressure
test point fitting.
12 Gas Soundness Check
Once the gas supply is connected, all joints must be checked for gas soundness . Note:
It is permissible to light the fire for short periods when the burner has not been filled with
the loose infill.
ELECTRICAL CONNECTION TO MAINS SUPPLY
1 It is recommended that the electrical connection to the mains supply is made via a fused
spur or an un-switched three-pin socket and plug. The supply MUST BE FITTED WITH A
3A FUSE.
2 The appliance is supplied with 2.5 metres of three-core mains cable pre- wired to the
circulation fan and its speed control switch. This should be routed to the power point as
inconspicuously as possible - i.e. chased into the plaster.
Filling the Burner.
Fill the burner tray level to the top using the ceramic fibre flakes provided making sure
that the burner ports between the flame guides down the centre are left completely clear.
Any flakes that are too large may be broken to fit.
Placing of the Refractory Logs.
Keep logs clear of the pilot flame to ensure good cross lighting.
Lay the logs a shown in the Figures.

8
Closing the Glass Door.
1 Place the glass door in position over the studs on the heat exchanger making sure the
joint in the rope seal lies along the lower edge. Secure in position with the 2 nuts and 2
screws. Tighten evenly.
Installing The Decorative Frame.
1 Hook the decorative frame over the supporting lugs within the convector box.
COMMISSIONING
WARNING.
This appliance is fitted with a spillage monitoring system consisting of a flue
temperature switch. Should the chimney become blocked, the sensor will become
hot, and the appliance will go out. The installer must not attempt to adjust this
system, nor shall he put it out of operation. Should any part of this system need to
be replaced, only original manufacturers parts shall be used.
1 Before attempting to light the appliance the gas supply must be turned on by removing
the cap from the isolator fitting and unscrewing the plug all the way out. Replace the cap
making sure that the tab engages with the slot in the top of the plug. Tighten the cap
securely. Light the appliance in accordance with the instructions in the lighting section.
Briefing the User
1 Demonstrate the full operation of the appliance to the customer.
2 Inform the customer that all cleaning procedures should be carried out only when the
appliance is cold.
3 Leave these instructions with the customer.
4 Advice the importance of having the appliance serviced and the chimney checked for
clearance of combustion products on an annual basis.
SERVICE AND MAINTENANCE
BEFORE ANY SERVICING IS CARRIED OUT ISOLATE THE APPLIANCE FROM THE
GAS SUPPLY. AFTER REFITTING THE APPLIANCE, CHECK FOR GAS
SOUNDNESS AT ALL GAS JOINTS AND TEST FOR SPILLAGE.
This product may use fuel effect pieces containing Refractory Ceramic Fibre
(RCF). This material contains man-made vitreous silicate fibres. Excessive
exposure to these materials may cause temporary irritation to eyes, skin and
respiratory tract; consequently, it makes sense to take care when handling these
articles to ensure that the release of dust is kept to a minimum.

9
To ensure that the release of fibres from these RCF articles is kept to a minimum,
during installation and servicing we recommend that a HEPA filtered vacuum
cleaner is used to remove any dust accumulated in and around the appliance
before and after working on the appliance. We recommend that any replaced items
are not broken up, but are sealed within heavy duty polythene bags and clearly
labelled as RCF waste. RCF waste is classed as a stable, non-reactive hazardous
waste and may be disposed of at landfill sites licensed to accept such waste.
Protective clothing is not required when handling these articles but we
recommend that the normal hygiene rules are followed of not smoking, eating or
drinking in the work area and that hands are washed before eating or drinking.
The appliance should be serviced at least once a year by a gas fitter registered in
The UK & Ireland . This is the basic procedure, and law of the EU.
1 Unclip and lift away the decorative frame.
2 Unscrew the two nuts +two screws and remove the glass door.
3 The refractory logs should be taken off the fire and shaken to remove any debris but
should only be cleaned if absolutely necessary. This should be done by gently brushing
with a soft brush in a direction away from the person and any persons nearby. This
operation should be performed outside facing downwind. A vacuum cleaner must not be
used for this purpose.
4 The gas supply should have been turned off the isolation point. Disconnect the gas
supply pipe from the pressure test point fitting. Remove the burner / control unit and lift it
out of the firebox as described in the installation section.
5 Empty the ceramic flakes from the burner on to a clean surface and thoroughly clean the
burner ports.
6 Operate the spark generator and observe that the spark is satisfactory.
7 Lay the control mount assembly on a flat surface and remove, clean and replace the
main injector.
8 Any soot or debris should be removed from the flue ways and it should be inspected for
soundness. To inspect the flue the main heat exchanger will have be removed as
described in the installation section.
9 Refit the burner / control unit in position. Re-connect the gas supply. Refill the burner with
the ceramic flakes making sure none is placed over the burner ports. Replace the
refractory logs on the burner.
10 Replace the glass door and secure. Tighten the fastenings evenly.
AFTER REFITTING THE APPLIANCE CHECK FOR GAS SOUNDNESS AT ALL GAS
JOINTS AND TEST FOR SPILLAGE.
12 Replace the decorative frame.
13 The service record sheet enclosed with these instructions should be complete to
maintain the validity of the warranty.

10
USERS GUIDE
Useful tips & recommendations
Once your appliance has been fitted, the following recommendations are made to ensure
you enjoy the best results from your purchase;
1 The installation of this appliance must have been carried out by a qualified installer and
in accordance with all local laws and regulations.
2 The chimney must be swept before the appliance is installed and checked annually to
ensure continued clearance of combustion products and that there is no excessive build-
up of soot.
3 The glass door and the upper part of the decorative frame are considered to be a
working surfaces and as such will become hot when in use. Care should be exercised
when using the controls of the appliance when it is hot. We also recommend that a
fireguard be fitted for the protection of young children, the elderly or infirm.
4 When new any ceramic components may produce a slight odour, but this will completely
vanish after a few hours of use.
5 The appliance MUST NOT be used with the door open or with the glass panel removed.
If there is any suspicion of damage to the glass the appliance must not be used.
6 Check periodically that any purpose-made ventilation is free from obstruction.
7 To obtain the best results from your fire we recommend that it be serviced annually.
8 These instructions are provided to assist you to operate the fire correctly and should be
kept in a safe place.
9 If you have any reason to suspect a gas leak, turn off the appliance at the isolating point
and contact your installer.
10 This appliance is fitted with a flue blockage device that will shut off the appliance in the
event of abnormal flue conditions. If this device repeatedly shuts off the appliance your
installer should be informed and the cause rectified. This device is NOT a substitute for
an independently mounted carbon monoxide detector.
11 Curtains should not be hung above the appliance.
Operation of the fire
1 It should be noted that your fire is fitted with a Flame Supervision Device, which cuts off
the gas supply to your fire if, for any reason the pilot light is extinguished. The pilot flame
heats the thermocouple probe and allows gas to flow to the burners. If due to pilot failure,
the thermocouple cools, no gas will flow to the main burner. If the fire is turned off or the
flames go out, wait for AT LEAST 3 MINUTES before attempting to relight the fire.
2 The power supply to the appliance should be left on at all times as the appliance is fitted
with a fan to increase the circulation of convicted air. The fan will operate when the
interior temperature has reached approximately 50ºC. The fan has two speed settings
which are controlled by a switch located beside the gas control. The lowest position is
slow and the upper position is fast. The fan may be run at whatever speed the user finds
most appropriate. Once the fire has been switched off, the fan will continue to run until
the interior temperature reduces to 37ºC. The fire is to be used with the circulation fan
turned ON. The control knob should be set to MIN to avoid the appliance overheating.

11
Lighting the Appliance
1 Open the louvered door at the base of the appliance under the glass door by pulling on
the top edge at the sides.
2 Push in and turn the control knob anti-clockwise to the PILOT position.
3 Hold the knob in for several seconds to purge any air from the system.
4 With the knob still depressed turn it from the "OFF" position to the "PILOT" position until
the pilot light ignites Continue to depress the control knob for a further 10-15 seconds.
Release the control knob, the pilot should stay alight. If the pilot flame goes out, repeat
the process, holding down the control knob for a slightly longer period.
5 Depress the control knob slightly and turn anti-clockwise to the MAX position. The main
burner should now light.
6 Turn the control knob clockwise to the MIN position. The flames will get lower but the
main burner should remain alight.
7 Depress the control knob slightly and turn clockwise to the PILOT position. The main
burner should go out but the pilot flame should remain alight.
8 Depress the control knob slightly and turn clockwise to the OFF position. The pilot flame
should go out.
IMPORTANT:
After turning OFF, or if the pilot burner or main burner go out for any reason, wait 3
minutes before attempting to relight.
Turning the fire off.
1. Slightly depress the control knob and turn clockwise to the "PILOT" position. The main
burner will go out but the pilot will remain alight.
FIG. 7

12
2. Depress the control knob and turn clockwise to "OFF". The fire is now turned off
completely.
REMOTE CONTROL ELECTRONIC IGNITION SYSTEM
Igniting the Appliance.
Simultaneously press the “(Spark) OFF” and “▲ or big flame” buttons of the receiver for ignition.
(Fig-A).
An acoustic signal indicates that the start sequence has begun.
The electronic system then checks that the main gas is flowing and ignites the main burner; this
may take up to 20 seconds.
IMPORTANT: During the lighting procedure the main valve button
must be in the ON position. (Fig-B).
Remember if you are trying to light the fire with your remote control and there is no acoustic
signal or the pilot light does not ignites, change the batteries in the remote control and the
receiver. The receiver box is located in the lower part of the insert in a box, next to the speed
switch. In order to change the batteries of the receiver you will have to loose a screw. (Fig-C).
Adjusting the Heat Setting
You are now able to use the remote control. To increase the flame, the top button (▲ or big
flame ) should be depressed. Pressing the lower button (▼ or small flame) on the handset will
reduce the flame. It is also possible to turn the main burner all the way down so that it is
effectively off, leaving only the pilot ignited.
You can control the fan speed with help of the ventilator switch. (Fig-D).
Fig-A Fig-B Fig-C Fig-D
Extinguishing the Appliance Fully
From any heat setting, press the “OFF” button for a few seconds. This will cause the burner to
fully extinguish.
IMPORTANT:
After turning OFF, or if the pilot burner or main burner go out for any reason, wait 3
minutes before attempting to relight. There is a internal mechanism that will block it
during some minutes.

13
Remote control with climate control system (depending the gas fire model)
Display setting
After having changed the batteries, press the symbols (OFF) and (▼) and select ºF/12
hours or ºC/24 hours.
Hour setting
For the selection of the hour you have to press (▼) and (▲). Once the screen light you
can proceed to the hour (▲ ) and (▼ ) minutes setting.
Setting of the temperature
Press SET and select ☼or C (Temperature day or night). Once choose the option press
SET till it flickers. Then adjust the temperature pressing (▲) or (▼). (Fig.1).
Setting the timer
Press SET alternatively till the option TIMER appears. Keep pressing SET till it flickers.
The program 1 (P1), ☼ set the lighting and Cswitch it off . In both options you an
adjust the time by pressing (▼) or (▲). For the second program (P2) proceed the same
way. (Fig.2)
Fig. 1 Fig.2 Fig.3
Please note it is advised to replace the batteries yearly ,on the remote and receiver,
whilst servicing the appliance.
Cleaning the fire
Ensure that the appliance is cool. Regular dusting with a dry cloth is usually all that is
necessary to keep your fire looking at it's best. From time to time it may be necessary to
clean the steel surface with a slightly damp cloth - do this while the fire is cool and
ensure that no water remains on the appliance surface.
Glass.
Let the fire and glass cool completely. Only the outside of the glass can be cleaned by
the user. Wash the glass with warm water, using a soft paper towel or cloth, rinse and
dry thoroughly. Never use abrasive or harsh chemicals to clean the glass.
For stubborn deposits use a cleaner available from your dealer. Do not allow the cleaner
to touch any brass ornamentation.
1 Ensure that the fire is cold before undertaking any cleaning. Remember that heat is
retained for some time after the fire is switched off. In normal use your fire requires only
minimal cleaning. Some soot may form on any ceramic pieces placed in the flames but
this is generally harmless unless an excessive amount is deposited.
2 If large pieces of debris are found in the fire, sufficient to alter the appearance or
operation of the appliance, the chimney / flue should be inspected and the appliance
serviced before further use.
3 In any event, the chimney should be checked annually to ensure continued clearance of
the combustion products and that there is no excessive build-up of soot.

14
Troubleshooting
Pilot sparks but does not light –
No gas to fire, check isolators are open.
Pipework blockage, clean out.
Air not fully purged, repurge supply or wait longer.
Spark earthing to metal work, reset gap correctly.
Check for spilled ceramics in pilot area.
Blocked pilot, clean out internally.
Pilot lights but then goes out –
Severe restriction in gas supply, clear obstruction.
Faulty thermocouple, replace pilot unit.
Hold control knob in for longer.
Check control knob does not foul control plate.
Fire does not spark at pilot –
HT lead detached, refit.
Spark gap too large or small, reset correctly.
Faulty piezo unit, replace.
Debris shorting out electrode, clean.
Fire runs for a time and then cuts off –
Excessive room draught or flue pull, rectify.
Loose or faulty thermocouple, rectify.
TTB system in operation.
Lint in pilot aeration hole, clean thoroughly internally
Pilot flame shrinks when fire is on high –
Poor gas flow to fire, check pressure with fire on high.
If pressure is low, remove any restriction in pipework or valve.
Check all isolators are adequately sized and fully open.
Check meter pressure is adequate.
Lint in pilot aeration hole, clean thoroughly internally.
Fire smells when first lit or in use –
Newness smell from brand new appliance.
Spillage occurring. Carry out spillage test and rectify any
problems.
Low temperature sealants or combustible materials used in
incorrect positions
Failure of the fire not lighting remotely, may require new batteries been fitted to the hand set and receiver.
It is recommended to replace the batteries when the fire is been serviced on a yearly basis.
Guarantee
The guarantee is valid for a period of 2 years from the purchase date. This guarantee does not
cover parts normally subject to wear or which last less than the aforementioned Guarantee period, as
thermocouples, batteries, gaskets, painted parts, logs or stones. The ceramic glass is not included in the
guarantee.
The guarantee will be invalided by incorrect installation or misuse of the appliance.
During this period the Dealer undertakes to repair or replace the faulty parts. Such repairs shall not alter
the date of expiry of the Guarantee.
AMBIFUEGO RESERVES THE RIGHT TO MODIFY OR UPDATE ITS
PRODUCTS OR SPECIFICATIONS WITHOUT PRIOR NOTICE, AS ITS
POLICY IS ONE OF CONTINUAL IMPROVEMENT.