Ambifuego KALIDO77 Manual

TECHNICAL INFORMATION
32
PIN: 0063CL1279
Inlet Pipe connection 8mm Compression
Appliance mass 5kg
Electrical Supply 230 V ~ 50Hz 0.085A
Natural
Gas Category I2H I2E I2E+ I2L
Gas G20 G20 G20/G25 G25
Supply Pressure (mbar) 20 20 20/25 25
Pilot Burner SIT 0.977.113
Nominal Input (Gross kW) 8.8 8.8 8.8/8.0 8.0
Gas Rate (max. m³/hr) 0.838 0.838 0.838/0.886 0.838
Burner Pressure Mertik(Hot
mbar) 12 12 12/16.3 16.3
Burner Pressure Seagas(Hot
mbar) 10.8 10.8 10.8/14.7 14.7
Efficiency Class 2
Nox Class 4
Burner Injector 650
LPG
Gas Category I3B/P I3+ I3B/P
Gas G30/G31 G30/G31 G31
Supply Pressure (mbar) 30 28-30/37 37
Pilot Burner SIT 0.977.148
Nominal Input (Gross kW) 8.8
Gas Rate (max. m³/hr) 0.252 0.331
Burner Pressure Mertik(Hot
mbar) 28.9 36.8
Burner Pressure Seagas(Hot
mbar) 28.2 35.5
Efficiency Class 2
Nox Class 5
Burner Injector 240
Ambifuego
Avda. Cañada del Cura, 29
Poligono Industrial de Levante
03187 Los Montesinos (Alicante)
tel.: [phone]
[email protected] www.ambifuego.net
KALIDO77
USER, INSTALLATION AND SERVICING
INSTRUCTIONS (GB & IE)
Please read these instructions carefully before installation or use, and leave
with the customer for storage is a safe place for future reference.
This appliance has been designed and approved for use in other countries than shown on this
cover. To install in other countries it is essential to obtain the manual in the local translation.
Contact Ambifuego for further information.

GENERAL INFORMATION
2
This manual covers the following appliances:
Kalido77
Preliminary Notes Before Installation
The fire is designed to fit into a purpose made builder’s opening, and
use natural draught flues as listed in the Installation Requirements.
The appliance must be installed by a competent person in
accordance with Gas Safety (Installation and Use) Regulations 1998.
It is strongly recommended that a "Gas Safe" registered engineer be
used for this purpose.
Read all these instructions before commencing installation.
This appliance must be installed in accordance with the rules in force
and only used in a sufficiently ventilated space.
The appliance is designed for installation on to a non-combustible
hearth which must project at least 240mm in front of the appliance.
This appliance is factory set for operation on the gas type, and at the
pressure stated on the appliance data plate.
This appliance has an Electrically operated fan to power the forced
convection. This fan must not be disconnected or put out of operation
and the appliance must not be operated if the fan is broken.
The electrical supply must be connected before the appliance is
ignited.
If the power supply cord is damaged, it must be replaced by the
manufacturer, it's service agents or similarly qualified persons in
order to avoid a hazard.
TECHNICAL INFORMATION
31
LPG
AT Austria 
BE Belgium I3+ G30/G31@28-30/37mbar
CH Switzerland I3+ G30/G31@28-30/37mbar
CY Cyprus I3B/P G30/G31@30mbar
CZ Czech Republic I3+ G30/G31@28-30/37mbar
DE Germany 
DK Denmark I3B/P G30/G31@30mbar
EE Estonia I3B/P G30/G31@30mbar
ES Spain I3+ G30/G31@28-30/37mbar
FI Finland I3B/P G30/G31@30mbar
FR France I3B/P G30/G31@30mbar;
I3+ G30/G31@28-30/37mbar
GB United KingdomI3B/P G30/G31@30mbar;
I3+ G30/G31@28-30/37mbar
GR Greece I3B/P G30/G31@30mbar;
I3+ G30/G31@28-30/37mbar
HR Croatia I3B/P G30/G31@30mbar
HU Hungary I3B/P G30/G31@30mbar
IE Ireland I3+ G30/G31@28-30/37mbar
IT Italy I3+ G30/G31@28-30/37mbar
LT Lithuania I3B/P G30/G31@30mbar
LU Luxembourg 
LV Latvia 
MT Malta I3B/P G30/G31@30mbar
NL The NetherlandsI3B/P G30/G31@30mbar
NO Norway I3B/P G30/G31@30mbar
PL Poland 
PT Portugal I3+ G30/G31@28-30/37mbar
RO Romania I3B/P G30/G31@30mbar
SE Sweden I3B/P G30/G31@30mbar
SL Slovenia I3B/P G30/G31@30mbar
SK Slovakia I3B/P G30/G31@30mbar;
I3+ G30/G31@28-30/37mbar
TR Turkey I3B/P G30/G31@30mbar

TECHNICAL INFORMATION
30
Countries of Destination
The following tables gives detail of the Countries that these
appliances are approved for use within. The tables following
immediately on give the technical characteristics of the appliances.
Natural
AT Austria I2H G20@20mbar
BE Belgium I2E+ G20/G25@20/25mbar
CH Switzerland I2H G20@20mbar
CY Cyprus 
CZ Czech Republic I2H G20@20mbar
DE Germany I2E G20@20mbar;
DK Denmark I2H G20@20mbar
EE Estonia I2H G20@20mbar
ES Spain I2H G20@20mbar
FI Finland I2H G20@20mbar
FR France I2E+ G20/G25@20/25mbar
GB United KingdomI2H G20@20mbar
GR Greece I2H G20@20mbar
HR Croatia I2H G20@20mbar
HU Hungary 
IE Ireland I2H G20@20mbar
IT Italy I2H G20@20mbar
LT Lithuania I2H G20@20mbar
LU Luxembourg I2E G20@20mbar
LV Latvia I2H G20@20mbar
MT Malta 
NL The NetherlandsI2L G25@25mbar
NO Norway I2H G20@20mbar
PL Poland I2E G20@20mbar
PT Portugal I2H G20@20mbar
RO Romania I2H G20@20mbar
SE Sweden I2H G20@20mbar
SL Slovenia I2H G20@20mbar
SK Slovakia I2H G20@20mbar
TR Turkey I2H G20@20mbar
GENERAL INFORMATION
3
Contents
GENERAL INFORMATION . . . . 1
Important Safety Notice . . . . 4
General Fitting Information . . . 6
Battery type (Remote Versions only) . . 6
USER INFORMATION . . . . . 7
Mertik GV34 Manual Control (Twin Knobs). . 7
Mertik GV60 Remote Control (Simple Control) . 10
Seagas Manual Control (Single Control Knob). . 13
INSTALLER INFORMATION . . . . 15
Site Requirements . . . . 15
Ventilation . . . . . 16
Installing the Appliance . . . . 17
Setting Pressure . . . . 18
Testing and commissioning . . . 19
Installing the additional controls (Remote controls) 20
Motor Installation . . . . 20
Simple Version Up and Lower control only . 21
Micro Switch Installation. . . . 22
Arranging the Ceramic Fire-bed . . . 24
Log Arrangement . . . . 24
Flue Spillage Monitoring System. . . 25
Briefing the Customer . . . . 26
Servicing Instructions . . . . 27
Spare Parts . . . . . 28
Troubleshooting. . . . . 29
TECHNICAL INFORMATION . . . . 30
Technical Details . . . . 32

GENERAL INFORMATION
4
IMPORTANT SAFETY NOTICE
This appliance has a ceramic Fire-bed arrangement; this contains Refractory
Ceramic Fibres, which are man-made vitreous silicate fibres. Excessive
exposure to these materials can cause irritation to eyes, skin and respiratory
organs. Hence we recommend that when handling these materials the
release of dust should be kept to a minimum. During installation and
servicing we recommend that a HEPA filtered vacuum be used to remove
any dust and soot in and around the fire. If any of the ceramic fire-bed
components need to be replaced we recommend that the removed parts be
sealed in a heavy-duty polythene bag, and be labelled as RCF waste. RCF is
not “Hazardous waste” and can be disposed of at a licensed tipping site for
the disposal of industrial waste.
The appliance incorporates a permanent pilot. This is located on the front of
the burner, and must not be adjusted by the installer. This system must not
be put out of operation, and if any parts require changing, only original
manufacturer parts shall be used.
This appliance is designed to be used either Natural or LPG gas however,
each individual appliance is only capable of running off the type of gas
specified at the time of purchase. It is important to note that once a type of
gas has been specified the fire cannot run off any other type. The type of gas
that your fire is capable of burning is stated on the data information panel.
This appliance has been designed, tested and approved to meet standards
in place for product use, performance and safety. Installation of your
appliance must comply with current building regulations. It is therefore
recommend that a registered gas installer be employed for this task. The
engineer will provide you with information about the safety limits of the
installation and should fix a notice plate in a place where it can be readily
seen.
This appliance is designed as a decorative heating device and consequently
all body parts become very hot in use. Except for the control knob and
control access door, which are designed to stay cool, all other parts are
working surfaces and should not be touched.
The front of this appliance does not give full protection for young
children, the elderly or infirm, extra protection should be considered for
these conditions conforming to BS 6539 or BS 6778. The appliance is not
fitted with a functional integral guard. In normal use, consideration should be
given to the use of an additional guard, conforming to the standard above,
such that access to the open flame is minimised.
INSTALLER INFORMATION
29
Troubleshooting
Pilot sparks but does not light –
No gas to fire, check isolators are open.
Pipework blockage, clean out.
Air not fully purged, repurge supply or wait longer.
Spark earthing to metal work, reset gap correctly.
Check for spilled ceramics in pilot area.
Blocked pilot, clean out internally.
Pilot lights but then goes out –
Severe restriction in gas supply, clear obstruction.
Faulty thermocouple, replace pilot unit.
Hold control knob in for longer.
Check control knob does not foul control plate.
Fire does not spark at pilot –
HT lead detached, refit.
Spark gap too large or small, reset correctly.
Faulty piezo unit, replace.
Debris shorting out electrode, clean.
Fire runs for a time and then cuts off –
Excessive room draught or flue pull, rectify.
Loose or faulty thermocouple, rectify.
TTB system in operation.
Lint in pilot aeration hole, clean thoroughly internally
Pilot flame shrinks when fire is on high –
Poor gas flow to fire, check pressure with fire on high.
If pressure is low, remove any restriction in pipework or valve.
Check all isolators are adequately sized and fully open.
Check meter pressure is adequate.
Lint in pilot aeration hole, clean thoroughly internally.
Fire smells when first lit or in use –
Newness smell from brand new appliance.
Spillage occurring. Carry out spillage test and rectify any
problems.
Low temperature sealants or combustible materials used in
incorrect positions.

INSTALLER INFORMATION
28
Spare Parts
Burner,Natural XXxxxxx
Burner,LPG XXxxxxx
PilotNatural XXxxxxx
PilotLPG XXxxxxx
Injector Assembly Natural (650 Marking) XXxxxxx
Injector Assembly LPG (280 Marking) XXxxxxx
Control Valve (Mertik) XXxxxxx
SimpleRemote XXxxxxx
ClimateRemote XXxxxxx
Control Valve (Seagas) XXxxxxx
To replace these items, follow the procedure listed in the servicing
instructions above.
GENERAL INFORMATION
5
Bearing in mind that the heat given off by this appliance may affect articles
placed close to it, curtains should not be placed within 30cm.
The appliance is not designed as a dryer. It is not therefore recommended
that the appliance be used in such a manner. Do not place any articles within
30cm of this appliance as this may result in damage to the articles.
The installation must be carried out in accordance with the following
regulations:
The Building Regulations issued by the Department of the Environment, the
Building Standards (Scotland) (Consolidation) Regulations issued by the
Scottish Development Department.
BS 1251, BS 5440 parts 1 & 2, BS 5871 part 2, BS 6461 part1, BS 6891 and
BS 8303
In the Republic of Ireland the installation must also conform to the relevant
standards, particularly in regard to flue sizing and ventilation. Refer to
documents IS813, ICP3, IS327 and any other rules in force.
This appliance must be installed in accordance with the rules in force and
used only in a sufficiently ventilated space, and is intended for use on a gas
installation with a governed meter.
Before installation, ensure that the local distribution conditions (identification
of the type of gas and pressure) and the adjustment of the appliance are
compatible. The technical specification of this appliance is given on the rear
page of this manual.
The fuel bed or this appliance should not be disturbed, and rubbish or other
fuels must not be thrown onto the fire.
The Chimney should be checked regularly to ensure that all the products of
combustion are entering the flue or canopy, and that there is no excessive
build up of soot. If any soot is found to build up it must be removed as
described in the servicing instructions.
Ventilation must be checked regularly to ensure that it is free from
obstruction.

GENERAL INFORMATION
6
General Fitting Information
Inlet Pipe connection 8mm Compression
Flame monitor Permanent Pilot
Appliance mass 5kg
User control: Variable rotary control inc. integrated Piezo ignition,
Permanent pilot facility, Flame failure device and TTB flue blockage
Cut-out.
Before installation of these appliances, the area into which the fire is
to be fitted must be cleared of all debris (including dust), in particular
combustible material.
The appliance must sit on a hearth (or base surface) sufficient to
support the weight of the fire. The burner must then also be secured.
Brackets are supplied for this purpose.
The flue must be connected to only one fireplace, and the flue must
not vent more than one appliance (i.e. not shared with a gas back
boiler). There must be no opening in the flue apart from the one that
the appliance is installed into, and the one venting the gases into the
air. A suitable terminal may be fitted, such as class GC1, as
regulations allow.
Any flue damper plates or flue restrictors shall be removed or fixed
permanently in the fully open position.
The chimney must be swept before the appliance is installed and a
flue test in accordance with national regulations carried out.
This appliance has been tested for use with circular flues of a
minimum internal diameter of 125mm (5”).
The flue termination (cowl) must be of a type suitable for use with an
inset Decorative Fuel Effect Fire BS5871 part 3 contains further
details.
Battery type (Remote Versions only)
Receiver: 4x AA, R6 size.
Transmitter: PP3 (Alkaline only).
INSTALLER INFORMATION
27
Servicing Instructions
Ensure that the fire is fully cold before attempting service. A
suggested procedure for servicing is detailed below.
1. Lay out the dust sheet and tools.
2. Inspect the area around the top of the fireplace opening for signs
of spillage.
3. Carefully remove the ceramic components. Use a soft brush to
clean off ceramics, the use of a vacuum cleaner directly on the
ceramics is not recommended. Replace any broken ceramics.
4. Carefully remove the Grate, clean the grate and the top of the
burner, a vacuum cleaner and brush may be used.
5. Isolate the gas supply at the appliance inlet, and disconnect the
gas supply pipe.
6. Remove the screws securing the burner to the hearth.
7. Remove the burner unit from the fireplace opening.
6. Check the base of the fireplace opening for rubble accumulation
and remove. If debris is excessive, initiate remedial work on the flue.
7. Check the flue with smoke pellet for correct operation.
8. Strip off the burner pipes and clean thoroughly.
9. Clean out the injector and pilot assembly. DO NOT attempt to
dismantle the pilot unit.
10. Ensure the injector is aligned squarely in the injector bracket. Re-
assemble and re-fit the burner tray.
11. Re fit and replace the ceramics, using genuine spares where
necessary.
12. Turn on the gas supply, and leak test.
13. Check any purpose provided ventilation is un-obstructed.
14. Light the fire and test for spillage.
15. Check setting pressure and safe operation of the appliance.

INSTALLER INFORMATION
26
Briefing The Customer
All instructions must be handed to the user for safekeeping. Show
the customer how to light and control the fire.
After commissioning the appliance, the customer should be
instructed on the safe use of the appliance and the need for regular
servicing. Frequency of service depends on usage, but MUST be
carried out at least once annually.
Operating The Appliance
If the Flame Supervision Device is extinguished either
intentionally or unintentionally, no attempt should be
made to re-light the gas until at least 3 minutes have
elapsed.
Mertik GV34 Manual Control
Igniting the Pilot Light
Turn the Right-hand knob
slightly anti-clockwise towards
the ignition position until
reaching stop, depress and
hold for five seconds (only
pilot gas flows).
Whilst still depressed, turn
further in an anti-clockwise
direction to activate the piezo. If the pilot does not light, repeated
immediately.
Continue to keep the knob depressed for a further 10 seconds, after
the pilot has been lit.
Upon releasing the knob, the permanent pilot will remain lit, if not
return to off position and repeat.
If under any circumstances the electric spark fails, the pilot may be lit
manually by proceeding with the ignition sequence as previously
described, and after turning the control knob through the spark
position, the knob should be held in and the pilot lit with a match or
other lighter.
Running the appliance at high output
Ignite permanent pilot as
shown in “Igniting the pilot
light”.
Turn the Right-hand control
knob (A) anti-clockwise to the
setting, which shows the
larger flame.
USER INFORMATION
7

USER INFORMATION
8
Turn the Left-hand control knob (B) anti-clockwise to the highest
setting (large flame).
The appliance is now burning at its highest operating output.
Running the appliance at lower setting
Ignite permanent pilot and run
appliance at “High” setting for
a minimum of 10 minutes as
shown previous.
With the Left-hand control
knob (B) at the highest setting,
rotate in a clock-wise direction
to the lower setting as
required.
The appliance is now operating at lower operating output.
Extinguishing the appliance back to permanent pilot
setting
From any heat setting, turn the
Right-hand knob (A) in a
clockwise direction to the
“Pilot” position (the smaller
flame).
Extinguishing the appliance fully
From any heat setting, turn to
“Pilot” as in “Extinguishing the
appliance back to permanent
pilot setting”.
Depress the same knob
slightly and turn clockwise to
“Off” position (filled circle).
INSTALLER INFORMATION
25
Flue Spillage Monitoring System
This fire is fitted with a flue spillage safety device (TTB). If the fire
shuts down during use for no apparent reason then several things
may be suspected. If a door or window has been opened creating a
draught, then pilot disturbance is the problem, and removal of the
draught should resolve this. The gas pressure reaching the fire must
also be checked. The thermocouple connection into the back of the
gas control valve may also have worked loose during installation,
simply tighten to remedy if this is the case.
If pilot disturbance is not the cause, then the TTB safety system may
be in operation. Switch the appliance OFF, check the flue and carry
out any remedial work required. Relight the fire and carry out a
spillage test. DO NOT allow the appliance to be used if it continues to
fail a spillage test.
The spillage monitoring system shall not be adjusted, modified, or put
out of operation by the installer. Any spare parts fitted MUST be of a
type supplied for the purpose by the appliance manufacturer.
If the fire is not spilling, then further guidance should be sought, using
the Troubleshooting section as a guide.

INSTALLER INFORMATION
24
Arranging The Ceramic Fire-bed
Only the ceramics supplied with this appliance are to be used. The
ceramics must be laid only as shown on the following pages.
Replacement parts including mat are available from your dealer, but
should only be installed by a qualified installation engineer.
Log Arrangements
Ensure that the Grate, is sitting firmly on the base of the fire.
Scatter the bag of Embers evenly over the burner and grate. Ensure
that none enter the Pilot shield.
Place the six logs as shown above.
Make sure that the Pilot Flame is not impinged, that it cross lights to
the main burner and is always visible.
The arrangement is now complete; recheck the lighting of the fire
(from cold).
1 23
4 5
6
USER INFORMATION
9
In the extent of a flue blockage or spillage, the monitoring system will
operate and turn off the fire. If this occurs extinguish the appliance
fully and re-light following the procedures as previously described.
If the fire repeatedly shuts down by the monitoring system, then a
specialist engineer should be informed.
REMOTE CONTROL (SIMPLE VERSION)
For the Remote control handsets to work, the receiver must be fitted.
See additional notes in the “Installer” section for fitting details. Please
note that no remote packages are available for the Single knob
control version.
Ignite the pilot as described
for the “Manual Control”
above. Turn Right-hand
control (A) anti-clockwise until
it is on the large flame setting.
You are now able to use the
remote control. To increase
the flame, the top button
should be depressed. Pressing the lower button on the handset will
reduce the flame. It is also possible to turn the main burner all the
way down so that it is effectively off, leaving only the pilot ignited.
When using the remote control system,
the appliance also maintains full manual
control. Hence the fire can be operated
using either the Manual Controls of the
Remote Handset.

USER INFORMATION
10
Mertik GV60 Fully Automatic System
Setting the Electronics Code
A code is selected automatically for all controls from among 65,000
random codes available.
The receiver has to learn the code of the handset:
- Power up Handset.
- Power up Receiver (LED flashes).
- Whilst flashing, press any button.
- When the Receiver LED stops flashing, the code is set.
- The remote defaults to Manual Mode on Start-up.
Setting °C/24 Hour or °F/12 Hour Clock.
Press OFF and (▼) until display changes from °F/12 hr to °/24/hr
clock or visa-versa.
Setting the time.
Simultaneously press the (▼) and (▲) buttons, the display now
flashes.
Press (▲) to set the hour and (▼) to set the minute.
Press OFF to return to manual mode.
Igniting the Appliance.
Simultaneously press the “ OFF” and “▲” buttons of the receiver
for ignition.
An acoustic signal indicates that the start sequence has begun.
The electronic system then checks that the main gas is flowing and
ignites the main burner; this may take up to 20 seconds.
(NOTE: During start-up, override knob cannot be in Manual position.)
Changing the Mode of Operation.
Briefly pressing the SET button changes the mode of operation in the
following order:
Man - Temp - Temp - Timer - back to Man
Man - Manual Flame Height Adjustment.
You are now able to use the remote control. To increase the flame,
the top button (▲) should be depressed. Pressing the lower button
(▼) on the handset will reduce the flame.
INSTALLER INFORMATION
23
The receiver unit should be located away under the fire, ensure that
the receiver is located on its special bracket that will keep the
receiver at a temperature below 60ºC, and that the customer knows
where the receiver is for future battery replacement.
Check the system.

INSTALLER INFORMATION
22
Micro Switch Installation
This procedure is to be followed for the installation of the Micro
Switch required for the “Climate Control System”, the micro switch
not being required for
the “Simple” version.
The Micro Switch fits
onto the Plastic Cover of
the valve, sitting on a
location lug moulded
into the cover a self
tapping screw is
provided to fix the
switch in location.
Assuming the motor has
already been fitted, as
shown above, the Control valve is now ready to be fitted with the
Climate Control System.
Climate Control System
This requires no external electrical power to operate. The receiver
unit has a unit that has only one lead. This lead has four plugs (two
larger plugs of different sizes and two plugs the same size). The two
larger plugs fit onto the two spade plugs on the top of the Gas
Control unit, the orientation of
these plugs are important. The two
smaller plugs fit on to the small
spade connectors on the side of
the control unit.
Install the batteries into the
receiver and the handset; these
will be 4 x 1,5V AA alkaline and 9V
PP3 alkaline respectively.
This Receiver/Handset works using sound waves, and as such no
direct line of sight is required between the two items. Provided that
the distance between the receiver and handset is less than 10m, the
system will work.
USER INFORMATION
11
It is also possible to turn the main burner all the way down so that it is
effectively off, leaving only the pilot ignited.
Extinguishing the Appliance Fully
From any heat setting, press the “ OFF” button for a few seconds.
This will cause the burner to fully extinguish.
The system has a safety interlock which will not allow the Ignition
until the Interlock rests (this may take a few minutes).
Temp - Daytime Temperature mode.
(appliance must be in standby mode; pilot ignited): The room
temperature is measured and compared to the set temperature. The
Flame height is then automatically adjusted to achieve the Daytime
set temperature.
Temp - Night time setback Temperature mode.
(appliance must be in standby mode; pilot ignited): The room
temperature is measured and compared to the Night time Setback
temperature. The Flame height is then automatically adjusted to
achieve the Night time Setback temperature.
Timer mode.
(appliance must be in standby mode; pilot ignited): The Timer setting
allows you to set 2 burner Temp times and 2 burner Temp times
every 24 hrs.
For Temp to operate as a thermostat, TEMP must be set at 4°C or
higher.
If the Temp setting is decreased to - -, the motor will turn the valve
to the standby position in the moon times and await the next burner
Temp cycle.
Setting the Temperature.
Select either the Temp MODE or the Temp MODE by briefly
pressing the SET button.
Hold the SET button until the TEMP display flashes.
Set the desired temperature with (▲) or (▼) .
Press OFF to complete program.
Setting the Timer.
Select Timer mode by briefly pressing the SET button.

USER INFORMATION
12
Press and hold the SET button until the P1is displayed, and the
time flashes. Set the hour by pressing the (▲) and set the minutes by
pressing the (▼) .
Briefly press SET button for the next burner cycle time.
Once all 4 times are set, press OFF to complete programming.
Manual Override
The system has a “Manual Override” feature that allows manual
operation without battery power. For manual operation, turn the
override knob to the “MAN” position. There is an opening that allows
access to the magnet stem, this should be pushed in to allow gas to
pass to the pilot. This stem must be held in whilst the Piezo igniter *
is depressed to spark the Pilot. The stem must be held in for a further
15 seconds until the pilot light establishes. If the Pilot does not hold
when the stem is released, repeat the process.
When the pilot is established, the “Override” Knob may be turned to
the “ON” position. Control of the gas is then possible using the
second control.
To turn the appliance off using the manual override, flip the “ON-
OFF” switch.
Please note * - The Manual Piezo Igniter is only available if
purchased as an optional Extra, however the manual “ON-OFF” and
Manual flame height setting is always available.
INSTALLER INFORMATION
21
Simple Version Up and Lower control only
This requires no external electrical power to operate. The receiver
unit has a unit that has only one lead. This lead has two plugs (of
different sizes), these will plug into the two spade plugs on the front
of the Gas Control
unit.
Install the batteries
into the receiver and
the handset; these
will be 4 x 1,5V AA
alkaline and 9V PP3
alkaline respectively.
This
Receiver/Handset
works using sound
waves, and as such
no direct line of sight
is required between
the two items. Provided that the distance between the receiver and
handset is less than 10m, the system will work.
The receiver unit can be hidden away under or behind the fire,
ensure that the receiver is located in an area that has a temperature
below 60ºC, and that the customer knows where the receiver is for
future battery replacement.
Check the system.
Batter
y
Cove
r
Receive
r
Lead

INSTALLER INFORMATION
20
Installing the Additional Controls (Remote Control)
Motor Installation
This procedure is to be followed for the installation of the Motor Unit,
which must be fitted to use all remote control options, except the
Fully Electronic Ignition System which has the motor built in.
Remove the retaining screw, (Figure 1) and by using the blade of a
small screwdriver, pry off the cover (opposite end of the cover to the
screw) (Figure 2).
Turn the geared knob fully counter clockwise to the end stop position.
Place the motor unit into position as shown in Figure 3. The motor
should fit into location and sit in place with the gear mating with the
teeth of the geared knob.
Replace the Plastic cover and replace
the retaining screw (without the metal
sleeve around the screw), this retains
both the cover and the motor.
The Control valve is now ready to be
fitted with the simple up/down control
system.
Fi
g
1 Fi
g
2
Fi
g
3
USER INFORMATION
13
Seagas Manual Control
Igniting the Pilot Light
Turn the Control knob slightly anti-
clockwise towards the ignition
position until reaching stop,
depress and hold for five seconds
(only pilot gas flows).
Whilst still depressed, turn further
in an anti-clockwise direction to
activate the piezo. If the pilot does
not light, repeated immediately.
Continue to keep the knob depressed for a further 10 seconds, after
the pilot has been lit.
Upon releasing the knob, the permanent pilot will remain lit, if not
return to off position and repeat.
If under any circumstances the electric spark fails, the pilot may be lit
manually by proceeding with the ignition sequence as previously
described, and after turning the control knob through the spark
position, the knob should be held in and the pilot lit with a match or
other lighter.
Running the appliance at high output
Ignite permanent pilot as shown in
“Igniting the pilot light”.
Turn the control knob fully anti-
clockwise to the High setting.
The appliance is now burning at its
highest operating output.
Running the appliance at lower setting
Ignite permanent pilot and run
appliance at “High” setting for a
minimum of 10 minutes as shown
previous.

USER INFORMATION
14
With the control knob at the highest setting, rotate in a clock-wise
direction towards the lower setting as required.
The appliance is now operating at lower operating output.
Extinguishing the appliance back to permanent pilot
setting
From any heat setting, turn the
Control knob in a clockwise
direction to the “Pilot” position.
Extinguishing the appliance fully
From any heat setting, turn to
“Pilot” as in “Extinguishing the
appliance back to permanent pilot
setting”.
Depress the control knob slightly
and turn clockwise to “Off” position.
In the extent of a flue blockage or spillage, the monitoring system will
operate and turn off the fire. If this occurs extinguish the appliance
fully and re-light following the procedures as previously described.
If the fire repeatedly shuts down by the monitoring system, then a
specialist engineer should be informed.
INSTALLER INFORMATION
19
Testing and Commissioning
Turn on and test the gas supply up to the fire for any leaks, in
accordance with current edition of BS6891.
Test the setting pressures as detailed on page **.
Perform a spillage test as detailed on page **.
When the appliance is first used, the coating of various parts may
cure. It is advisable to ventilate the room during this period for at
least one hour.

INSTALLER INFORMATION
18
Setting Pressure
Remove the screw from the pressure test point.
The pressure test point is situated on the side of the gas control.
The setting pressure should be in accordance with the figures stated
on page 32 of these instructions. The fire is factory set to achieve
these pressures, and any significant variation could indicate a supply
problem.
If the pressure is too high, the gas supply meter may be set
incorrectly. This should be checked with the fire running and if
necessary reset by the gas supplier.
If the pressure is too low, then check the meter governor pressure
with the appliance running. If this is incorrect it will need to be reset
by the gas supplier. If the setting pressure is too low, but the meter
pressure is acceptable, then a problem in the supply pipework is to
be suspected. This will be dirt and debris, kinked or inadequate size
pipes, restriction in a fitting or solder flashing across a joint. (NOTE:
you will not get an accurate reading of the inlet pressure with a
pressure gauge on the end of the supply pipe - this is the static
pressure in the system. You must use a T piece and measure the
supply pressure with the fire on High - the dynamic pressure). Refit
and tighten the screw into the pressure test point when the test is
complete.
Site Requirements
The fireplace opening should be inspected and repairs made where
necessary. It will usually be necessary to remove any chair brick that
may be in place.
The opening WIDTH dimension should have a minimum size of
685mm.
The opening HEIGHT dimensions should have a minimum size of
500mm.
Opening DEPTH should have a minimum size of 450mm.
This appliance requires a natural draught flue system which may be
one of the following;
225mm x 225mm (9in x 9in) brick or stone.
125mm (5in) minimum diameter lined brick or stone.
125mm (5in) minimum diameter twin wall flue conforming to BS 715.
Any existing under grate draught device must be sealed off.
The opening wall must be non-combustible.
The appliance requires a hearth with non-combustible surface of at
least 12mm thick. The top surface must be at least 50mm above the
surrounding floor level, or be surrounded by a raised edge or fender
50mm high.
A combustible shelf may be fixed to the wall above the fire, providing
that it is a minimum distance of 300mm above the fire.
A non-combustible shelf may be fitted to within 10mm of the top edge
of the fireplace opening.
Combustible materials, such as wood, may be fitted to within 100mm
(4in) of either side of the fireplace opening, providing the forward
projection does not exceed 100mm (4in).
Any combustible side walls must be at least 500mm to the side of the
radiant heat source.
INSTALLER INFORMATION
15

INSTALLER INFORMATION
16
As with all heating appliances, any decorations, soft furnishings, and
wall coverings (i.e. flock, blown vinyl and embossed paper)
positioned too close to the appliance may discolour or scorch.
Ventilation
This product is rated in excess of 7kW, and it is a legal requirement
to have 100cm² of ventilation if the input is in excess of 7kW. Thus
100cm² of ventilation is required.
If spillage is detected when commissioning the appliance then
amongst other problems there may be insufficient natural ventilation
for the correct operation of the flue. This is potentially a greater
problem should the property be of modern nature. If the appliance
does not spill with windows open but does with windows closed, this
proves that lack of ventilation is the problem, if not; it will be the flue
at fault. Installation of an air brick is the best solution. Any ventilation
fitted must comply with BS 5871 part 3 and BS 5440 part 2.
Ventilation located underneath or within the immediate vicinity of the
fire MUST NOT be used as it may adversely affect the performance
of the spillage detection system.
Spillage detected during commissioning is almost always a result of
poor flue performance, which cannot be corrected by any amount of
ventilation.
For Republic of Ireland ventilation may be required, see IS 813,
ICP3, IS 327, and any other rules in force.
INSTALLER INFORMATION
17
Installing the Appliance
Notes: Ensure that the gas supply is isolated before commencing
installation of the appliance.
Check that the thermocouple connection nut into the rear of
the valve is secure.
Smoke test the flue to ensure proper draw and that there are
no leaks present.
Locate the gas supply point. This appliance is suitable for all gas
connections, including those concealed behind
the opening.
An isolation valve (conforming to national regulations) must be fitted
adjacent to the appliance which, when closed, allows the burner
assembly and controls to be disconnected for maintenance or repair.
Using 8mm diameter pipe, connect the appliance to the gas supply
point. The appliance must be fitted with rigid or semi-rigid pipe of
8mm external diameter.
Keep the amount of 8mm pipe used in the supply to a minimum - less
than 1.2m where possible. A long run of pipe may cause an
unacceptable drop in the supply pressure.
Secure the Burner to the floor using the provided brackets; these
should be screwed to the floor using rawplugs and screws.
Position the grate on top of the burner, so that the slot locates over
the burner tube. Ensure that the Pilot Cut-out correctly aligns with the
pilot of the burner and that the burner can Cross Light without any
impingement.