AMBROGIO L15 Deluxe User manual

2020 Installation Guide

ambrogiorobot.com
VIDEO

Small and cplicated gdens
Please refer to an Ambrogio Robot professional installer to install your robot
Look for him on www.ambrogiorobot.com

ambrogiorobot.com READ THE
MANUAL
VIDEO

1.1 Carefully pull off the components and check their integrity.
WHAT’S IN THE BOX
1
Robot Docking station
Transmitter Fixing pegs for
the docking station
Power cord Cutting height
adjusting key Power supply User manual
Perimeter wire joint Perimeter wire coil Docking station roof*
Carefully read the user manual. (*optional)

ambrogiorobot.com READ THE
MANUAL
VIDEO

NEEDED PARTS FOR INSTALLATION
2
Wire pliers
for electric cables Universal pliers HammerScrewdriver
DO NOT MAKE AMBROGIO WORK NEXT TO:
People Children Pets
SAFETY INSTRUCTIONS

ambrogiorobot.com READ THE
MANUAL
VIDEO

NO
OK
power supply unit
charging station
min height 160 cm
/ 63 "
min. distance
200 cm
/ 78,74 "
perimeter wire
perimeter wire
transmitter
75cm / 21/2’
3.1 Position the charging station at the edge of the lawn, preferably in the widest area. The selected position should be
at and within 8 metres of a power outlet.
4.1 The selected position must be at. Make sure the
lawn to be mowed does not contain holes, stones
or other obstacles.
4.2 Start laying the perimeter wire from the back of
the docking station and move along the outer edge
of the garden in a clockwise direction until you
reach the charging station again.
4.3 The perimeter wire can be buried (max 5 cm deep)
or laid on the ground and secured with xing pegs
4.4 Install the perimeter wire in a counter-clockwise
direction around any obstacles or areas
(swimming-pool, owerbed) where you do not
want the robot to go (refer to the manual for
more details).
4.5 Carefully follow the distances specied in the
Manual to guarantee excellent installation.
4.6 In case of impact resistant obstacles, it is possible
to choose whether delimit them or not.
4.7 In case of lawns with more areas and/or separated
areas, please refer to the manual.
DOCKING STATION POSITIONING
PERIMETER WIRE POSITIONING
NO NO
OK OK
NO NO
3
4

ambrogiorobot.com READ THE
MANUAL
VIDEO

3
56
4
1 2
5.1 If more than one perimeter wire coil is needed, use
the original joint to connect the additional coils.
5.2 Follow the procedure shown in the gure.
6.1 Unhook the transmitter (T).
6.2 Insert and secure the perimeter wire along the guide in the docking station.
6.3 Cut the excess perimeter wire to about 2 cm above the connectors.
6.4 Connect the input wire to the red terminal of the transmitter (B). Connect the output wire to the black terminal of
the transmitter.
6.5 Secure the docking station to the ground.
6.6 Install the power supply (A) and connect the plug of the power supply unit to the electric outlet.
6.7 Connect the power supply to the power outlet.
6.8 If the transmitter led blinks, the connection is correct.
protection (L)
current power supply unit (A)
transmitter (B)
H. min.
160 cm
(63.00 ")
transmitter (T)
perimeter wire (M)
connect to
the black terminal
connect to
the red terminal
POSSIBLE PERIMETER WIRE JUNCTION
CONNECTING THE PERIMETER WIRE TO THE CHARGING STATION
5
6
Before any intervention, disable the master electricity switch

ambrogiorobot.com READ THE
MANUAL
VIDEO

7.1 Adjust the cutting height.
7.2 Open the Ambrogio Remote APP and insert the
PIN 0000.
7.3 Start-up of the robot in the middle of the lawn and
control of its functioning for about 15 minutes.
7.4 Check the return into the docking station starting
the robot up from a point just after the docking
station.
7.5 Check that the robot recognizes the charge by
checking that the battery led turns x orange for a
few seconds.
7.6 Pause the robot with the STOP button.
7.7 From the Ambrogio Remote APP set the working
time and working areas, including any secondary
areas.
7.8 Setting for changing the PIN CODE.
7.9 Make sure the robot properly detects the charging
by showing the message “in charge”.
auto home
start
pause
ON
OFF
auto ALERT
“ON” KEY
“PLAY/PAUSE” KEY
BATTERY LED
“STOP” KEY (A)
8.1 Press STOP button.
9.3 Adjust the settings
according to the size and
characteristics of the lawn.
9.4 Periodically perform
maintenance.
9.1 Carefully read the user
manual.
9.2 Change the PIN from 0000
as soon as possible.
START-UP
STOP
OTHER OPERATIONS
7
8
9

Zucchetti Centro Sistemi SpA
Via Lungarno, 305/A
52028 - Terranuova B.ni (AR) - Italy
Phone [phone] - Fax [phone] Ambrogio Robot
project design: settore8.it
ambrogiorobot.com